Re: Thin Stock support block dimensions
Great job Mike, works just like it ought.DensonSent from Denson's iPhoneOn Feb 16, 2023, at 9:51 PM, Tim Ziegler wrote:Good deal, with a pc of stock that long you may want the second one in there too. Then also lighter cuts and you will have it made.Kind Regards,Timothy J. ZieglerZiegler WoodWork & Specialty14171 160th Ave.Foreston MN 56330320-294-5798 shop320-630-2243 cellOn Thu, Feb 16, 2023 at 7:54 PM Mike Newman <mrnewma...@outlook.com> wrote:I was able to sneak out to the shop tonight to try out the thin stock support. It worked almost perfect and much better than the first one I made. Turned down a poplar blank for my first tapered walking stick and there was limited chatter. Still a couple of things to pay attention to but definitely the way to go for me right now.<20230216_190339.jpg>On Wednesday, February 15, 2023 at 11:14:24 PM UTC-6 Curt George wrote: Very nice, Mike.I think it should work well for you.Best of luck.C.A.G. On Wednesday, February 15, 2023 at 06:44:51 PM EST, Mike Newman <mrnew...@outlook.com> wrote: I finished my new thin stock support earlier tonight based on the info you guys provided. I have not tried it yet but should work similar to the factory one. I will throw another walking stick blank up on the LOM this weekend and see how it works.On Monday, February 13, 2023 at 10:48:26 PM UTC-6 Denson Ingram wrote:Yes sir you are welcome.DensonSent from my iPadOn Feb 13, 2023, at 9:40 PM, Tim Ziegler <timjz...@gmail.com> wrote:Hey Denson thanks for jumping in on that. Great job.Kind Regards,Timothy J. ZieglerZiegler WoodWork & Specialty14171 160th Ave.Foreston MN 56330320-294-5798 shop320-630-2243 cellOn Mon, Feb 13, 2023 at 5:49 PM 'Denson Ingram' via Legacy Ornamental Mills <legacy-orna...@googlegroups.com> wrote:Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thickDensonSent from Denson's iPhoneOn Feb 13, 2023, at 5:20 PM, Mike Newman <mrnew...@outlook.com> wrote:Does anyone already have the dimension for the hdpe blocks used on the factory thin stock support? I finally found a block of the material that I can make my own, but wanted to get the dimensions. Overall dimensions and then size/position of the v-notch should be all I need. I will attach it to my cross member I used for my first trial design. If anyone has one of the actual factory take a few measurements and post them or email me direct. I can figure it out if nobody has a factory one, but thought I would quickly check before I go down that road? thanks -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGzZ8NYhZOBV-oos%2BmhbUAJonnDo7%3DNM-XX0xqyVBiwiA%40mail.gmail.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/640be98b-dc01-4a22-bbe5-f19a7c9a163dn%40googlegroups.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/93b9ab0c-db33-4070-b0fe-7e19733469bfn%40googlegroups.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-
Re: Thin Stock support block dimensions
Yes sir you are welcome.DensonSent from my iPadOn Feb 13, 2023, at 9:40 PM, Tim Ziegler wrote:Hey Denson thanks for jumping in on that. Great job.Kind Regards,Timothy J. ZieglerZiegler WoodWork & Specialty14171 160th Ave.Foreston MN 56330320-294-5798 shop320-630-2243 cellOn Mon, Feb 13, 2023 at 5:49 PM 'Denson Ingram' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com> wrote:Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thickDensonSent from Denson's iPhoneOn Feb 13, 2023, at 5:20 PM, Mike Newman <mrnewma...@outlook.com> wrote:Does anyone already have the dimension for the hdpe blocks used on the factory thin stock support? I finally found a block of the material that I can make my own, but wanted to get the dimensions. Overall dimensions and then size/position of the v-notch should be all I need. I will attach it to my cross member I used for my first trial design. If anyone has one of the actual factory take a few measurements and post them or email me direct. I can figure it out if nobody has a factory one, but thought I would quickly check before I go down that road? thanks -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGzZ8NYhZOBV-oos%2BmhbUAJonnDo7%3DNM-XX0xqyVBiwiA%40mail.gmail.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/9D120749-40C5-4613-826A-0E2254DD0EEB%40yahoo.com.
Re: Thin Stock support block dimensions
Hey Denson thanks for jumping in on that. Great job. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Mon, Feb 13, 2023 at 5:49 PM 'Denson Ingram' via Legacy Ornamental Mills wrote: > Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thick > Denson > Sent from Denson's iPhone > > On Feb 13, 2023, at 5:20 PM, Mike Newman wrote: > > Does anyone already have the dimension for the hdpe blocks used on the > factory thin stock support? I finally found a block of the material that I > can make my own, but wanted to get the dimensions. Overall dimensions and > then size/position of the v-notch should be all I need. I will attach it > to my cross member I used for my first trial design. If anyone has one of > the actual factory take a few measurements and post them or email me > direct. I can figure it out if nobody has a factory one, but thought I > would quickly check before I go down that road? thanks > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com?utm_medium=email_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com?utm_medium=email_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGzZ8NYhZOBV-oos%2BmhbUAJonnDo7%3DNM-XX0xqyVBiwiA%40mail.gmail.com.
Re: Thin Stock support block dimensions
I would have it but not until tomorrow for sure. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Mon, Feb 13, 2023 at 5:20 PM Mike Newman wrote: > Does anyone already have the dimension for the hdpe blocks used on the > factory thin stock support? I finally found a block of the material that I > can make my own, but wanted to get the dimensions. Overall dimensions and > then size/position of the v-notch should be all I need. I will attach it > to my cross member I used for my first trial design. If anyone has one of > the actual factory take a few measurements and post them or email me > direct. I can figure it out if nobody has a factory one, but thought I > would quickly check before I go down that road? thanks > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com?utm_medium=email_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFijhg2Sa%2ByTGTGgc0pAJpiCKRsqn45EwfDK2v4diZeXw%40mail.gmail.com.
Re: Thin Stock support block dimensions
thanks for the info both dim/tailstock reference. Makes perfect sense on using the tail stock as a reference to go with the overall dim provided by Denson. On Monday, February 13, 2023 at 6:30:36 PM UTC-6 Curt George wrote: > Mike. > A simple way to make your own steady rest is to make the cross members > first. then USING those mounted to the Legacy's rails, you can make your > blocks, By using your tailstock as a reference point, mark the steady > blocks so the center point of the tail stock is the middle of the V/ center > of the steady rest blocks. > > C.A.G. > > On Monday, February 13, 2023 at 06:49:27 PM EST, 'Denson Ingram' via > Legacy Ornamental Mills wrote: > > > Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thick > Denson > Sent from Denson's iPhone > > On Feb 13, 2023, at 5:20 PM, Mike Newman wrote: > > Does anyone already have the dimension for the hdpe blocks used on the > factory thin stock support? I finally found a block of the material that I > can make my own, but wanted to get the dimensions. Overall dimensions and > then size/position of the v-notch should be all I need. I will attach it > to my cross member I used for my first trial design. If anyone has one of > the actual factory take a few measurements and post them or email me > direct. I can figure it out if nobody has a factory one, but thought I > would quickly check before I go down that road? thanks > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com > > <https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com?utm_medium=email_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental...@googlegroups.com. > To view this discussion on the web visit > > https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com > > <https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com?utm_medium=email_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/f53d11c4-bbd8-43e3-b742-6c1f2d3b4538n%40googlegroups.com.
Re: Thin Stock support block dimensions
Mike.A simple way to make your own steady rest is to make the cross members first. then USING those mounted to the Legacy's rails, you can make your blocks, By using your tailstock as a reference point, mark the steady blocks so the center point of the tail stock is the middle of the V/ center of the steady rest blocks. C.A.G. On Monday, February 13, 2023 at 06:49:27 PM EST, 'Denson Ingram' via Legacy Ornamental Mills wrote: Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thick Denson Sent from Denson's iPhone On Feb 13, 2023, at 5:20 PM, Mike Newman wrote: Does anyone already have the dimension for the hdpe blocks used on the factory thin stock support? I finally found a block of the material that I can make my own, but wanted to get the dimensions. Overall dimensions and then size/position of the v-notch should be all I need. I will attach it to my cross member I used for my first trial design. If anyone has one of the actual factory take a few measurements and post them or email me direct. I can figure it out if nobody has a factory one, but thought I would quickly check before I go down that road? thanks -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/685657489.704049.1676334595002%40mail.yahoo.com.
Re: Thin Stock support block dimensions
Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thickDensonSent from Denson's iPhoneOn Feb 13, 2023, at 5:20 PM, Mike Newman wrote:Does anyone already have the dimension for the hdpe blocks used on the factory thin stock support? I finally found a block of the material that I can make my own, but wanted to get the dimensions. Overall dimensions and then size/position of the v-notch should be all I need. I will attach it to my cross member I used for my first trial design. If anyone has one of the actual factory take a few measurements and post them or email me direct. I can figure it out if nobody has a factory one, but thought I would quickly check before I go down that road? thanks -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com.
Thin Stock support block dimensions
Does anyone already have the dimension for the hdpe blocks used on the factory thin stock support? I finally found a block of the material that I can make my own, but wanted to get the dimensions. Overall dimensions and then size/position of the v-notch should be all I need. I will attach it to my cross member I used for my first trial design. If anyone has one of the actual factory take a few measurements and post them or email me direct. I can figure it out if nobody has a factory one, but thought I would quickly check before I go down that road? thanks -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com.
RE: revo thin stock support
Please forgive me but im not seeing a thin stock support in the pic that what we were talking about Or am I missing something? Bill From: legacy-ornamental-mills@googlegroups.com On Behalf Of 4 Jim Carpenter Sent: Wednesday, 31 March 2021 5:06 PM To: To: Subject: Re: revo thin stock support How would you compare them with those on my Steely Bill. On Tue, Mar 30, 2021 at 6:48 AM mailto:bulke...@mmnet.com.au> > wrote: Yes and yes very ridged Bill From: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> mailto:legacy-ornamental-mills@googlegroups.com> > On Behalf Of Tim Ziegler Sent: Tuesday, 30 March 2021 10:32 PM To: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> Subject: Re: revo thin stock support Hey Bill thanks for posting that. So its basically 1/2 or whats on the full size LOMs? Does it seem pretty ridgid? There is sure a lot of cool innovations went into these machines. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Tue, Mar 30, 2021 at 1:54 AM mailto:bulke...@mmnet.com.au> > wrote: Here is a pic of my revo thin stock support legacy to my knowledge never made one. Bill -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000101d72531%2434e977e0%249ebc67a0%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/000101d72531%2434e977e0%249ebc67a0%24%40mmnet.com.au?utm_medium=email_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLEk4p6C%2B4KmNhrBu4O_9fUUoprmh3hv5h%3DR32%3Dq2eKJLw%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLEk4p6C%2B4KmNhrBu4O_9fUUoprmh3hv5h%3DR32%3Dq2eKJLw%40mail.gmail.com?utm_medium=email_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000601d7255a%249a0ff3a0%24ce2fdae0%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/000601d7255a%249a0ff3a0%24ce2fdae0%24%40mmnet.com.au?utm_medium=email_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CA%2BTVV5vSNn1OoJGK0DU2pqFxovxgk_3G23NdSy0NdQz6yW2hrA%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CA%2BTVV5vSNn1OoJGK0DU2pqFxovxgk_3G23NdSy0NdQz6yW2hrA%40mail.gmail.com?utm_medium=email_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000401d72605%247e990b10%247bcb2130%24%40mmnet.com.au.
RE: revo thin stock support
Yes and yes very ridged Bill From: legacy-ornamental-mills@googlegroups.com On Behalf Of Tim Ziegler Sent: Tuesday, 30 March 2021 10:32 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: revo thin stock support Hey Bill thanks for posting that. So its basically 1/2 or whats on the full size LOMs? Does it seem pretty ridgid? There is sure a lot of cool innovations went into these machines. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Tue, Mar 30, 2021 at 1:54 AM mailto:bulke...@mmnet.com.au> > wrote: Here is a pic of my revo thin stock support legacy to my knowledge never made one. Bill -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000101d72531%2434e977e0%249ebc67a0%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/000101d72531%2434e977e0%249ebc67a0%24%40mmnet.com.au?utm_medium=email_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLEk4p6C%2B4KmNhrBu4O_9fUUoprmh3hv5h%3DR32%3Dq2eKJLw%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLEk4p6C%2B4KmNhrBu4O_9fUUoprmh3hv5h%3DR32%3Dq2eKJLw%40mail.gmail.com?utm_medium=email_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000601d7255a%249a0ff3a0%24ce2fdae0%24%40mmnet.com.au.
Re: revo thin stock support
Hey Bill thanks for posting that. So its basically 1/2 or whats on the full size LOMs? Does it seem pretty ridgid? There is sure a lot of cool innovations went into these machines. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Tue, Mar 30, 2021 at 1:54 AM wrote: > Here is a pic of my revo thin stock support legacy to my knowledge never > made one. > > > > Bill > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/000101d72531%2434e977e0%249ebc67a0%24%40mmnet.com.au > <https://groups.google.com/d/msgid/legacy-ornamental-mills/000101d72531%2434e977e0%249ebc67a0%24%40mmnet.com.au?utm_medium=email_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLEk4p6C%2B4KmNhrBu4O_9fUUoprmh3hv5h%3DR32%3Dq2eKJLw%40mail.gmail.com.
Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
for sure a big help. I have welders and a torch but most machining I have my Brother do. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sun, Nov 29, 2020 at 9:10 PM Ray Leaman wrote: > I was originally trained as a wood and metal patternmaker. Along the way > somewhere I moved more into woodworking and did not include metalworking in > my shop planning. Metal fabrication with these mills would definitely be a > plus. I may need to develop a relationship with a local machine shop. > > On Sun, Nov 29, 2020 at 9:16 PM Tim Ziegler wrote: > >> Where there's a will there's a way right. >> What I can't make my Brother can do. He's big into metal work of all >> kinds. >> >> Kind Regards, >> >> Timothy J. Ziegler >> Ziegler WoodWork & Specialty >> 14171 160th Ave. >> Foreston MN 56330 >> >> 320-294-5798 shop >> 320-630-2243 cell >> >> >> On Sun, Nov 29, 2020 at 8:13 PM Ray Leaman wrote: >> >>> I know. Sounds like you got the talent to make one yourself. >>> >>> On Sun, Nov 29, 2020 at 8:37 PM Tim Ziegler >>> wrote: >>> >>>> Yea just kidding around Ray. >>>> I will find one. or make one. >>>> Kind Regards, >>>> >>>> Timothy J. Ziegler >>>> Ziegler WoodWork & Specialty >>>> 14171 160th Ave. >>>> Foreston MN 56330 >>>> >>>> 320-294-5798 shop >>>> 320-630-2243 cell >>>> >>>> >>>> On Sun, Nov 29, 2020 at 4:59 PM Ray Leaman wrote: >>>> >>>>> Will do but don't hold your breath too long Tim. As you say, this >>>>> stuff is hard to come by. >>>>> >>>>> On Sun, Nov 29, 2020 at 1:55 PM Tim Ziegler >>>>> wrote: >>>>> >>>>>> wow you ever decide you don't have a use for that I've been looking >>>>>> for since I bought my LOM. >>>>>> The thin Stock Follower that is. >>>>>> >>>>>> Kind Regards, >>>>>> >>>>>> Timothy J. Ziegler >>>>>> Ziegler WoodWork & Specialty >>>>>> 14171 160th Ave. >>>>>> Foreston MN 56330 >>>>>> >>>>>> 320-294-5798 shop >>>>>> 320-630-2243 cell >>>>>> >>>>>> >>>>>> On Sun, Nov 29, 2020 at 11:15 AM Ray Leaman >>>>>> wrote: >>>>>> >>>>>>> New in the box (NIB) >>>>>>> >>>>>>> Thin Stock Support: Mounts to the underside of the adjustable bed >>>>>>> rail with 2 - 90 degree mounting brackets, and supports material while >>>>>>> milling thin stock between 5/8" and 1 7/8 " thick. >>>>>>> >>>>>>> Thin Stock Follower: Mounts to the router carriage. The vinyl dust >>>>>>> shields need to be removed to mount the follower. >>>>>>> Can only be used on straight round pieces (no tapers or curves). >>>>>>> Adjustable bed must be set level. Position support following behind the >>>>>>> cutter when milling stock round. Position support in front of the cutter >>>>>>> when milling spirals. >>>>>>> >>>>>>> Ray >>>>>>> >>>>>>> -- >>>>>>> You received this message because you are subscribed to the Google >>>>>>> Groups "Legacy Ornamental Mills" group. >>>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>>> send an email to >>>>>>> legacy-ornamental-mills+unsubscr...@googlegroups.com. >>>>>>> To view this discussion on the web visit >>>>>>> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com >>>>>>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com?utm_medium=email_source=footer> >>>>>>> . >>>>>>> >>>>>> -- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "Legacy Ornamental Mills" group. >>>>>> To u
Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
Any pics? On Sun, Nov 29, 2020 at 9:31 PM wrote: > No I made my own styles > > > > Bill > > > > *From:* legacy-ornamental-mills@googlegroups.com < > legacy-ornamental-mills@googlegroups.com> *On Behalf Of *Tim Ziegler > *Sent:* Monday, 30 November 2020 1:26 PM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: My 1200 - Accessories: Thin Stock Support and Thin Stock > Follower > > > > Did you make your own Bill? Angle bracket style Vertical vise. > > Or are you referring to the sylus's > > > Kind Regards, > > > > Timothy J. Ziegler > > Ziegler WoodWork & Specialty > > 14171 160th Ave. > > Foreston MN 56330 > > > > 320-294-5798 shop > > 320-630-2243 cell > > > > > > On Sun, Nov 29, 2020 at 8:24 PM wrote: > > I was an engineer machinist for over 20 years > > > > Bill > > > > *From:* legacy-ornamental-mills@googlegroups.com < > legacy-ornamental-mills@googlegroups.com> *On Behalf Of *Ray Leaman > *Sent:* Monday, 30 November 2020 1:13 PM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: My 1200 - Accessories: Thin Stock Support and Thin Stock > Follower > > > > I know. Sounds like you got the talent to make one yourself. > > > > On Sun, Nov 29, 2020 at 8:37 PM Tim Ziegler wrote: > > Yea just kidding around Ray. > > I will find one. or make one. > > Kind Regards, > > > > Timothy J. Ziegler > > Ziegler WoodWork & Specialty > > 14171 160th Ave. > > Foreston MN 56330 > > > > 320-294-5798 shop > > 320-630-2243 cell > > > > > > On Sun, Nov 29, 2020 at 4:59 PM Ray Leaman wrote: > > Will do but don't hold your breath too long Tim. As you say, this stuff > is hard to come by. > > > > On Sun, Nov 29, 2020 at 1:55 PM Tim Ziegler wrote: > > wow you ever decide you don't have a use for that I've been looking for > since I bought my LOM. > > The thin Stock Follower that is. > > > Kind Regards, > > > > Timothy J. Ziegler > > Ziegler WoodWork & Specialty > > 14171 160th Ave. > > Foreston MN 56330 > > > > 320-294-5798 shop > > 320-630-2243 cell > > > > > > On Sun, Nov 29, 2020 at 11:15 AM Ray Leaman wrote: > > New in the box (NIB) > > > > Thin Stock Support: Mounts to the underside of the adjustable bed rail > with 2 - 90 degree mounting brackets, and supports material while milling > thin stock between 5/8" and 1 7/8 " thick. > > > > Thin Stock Follower: Mounts to the router carriage. The vinyl dust > shields need to be removed to mount the follower. > > Can only be used on straight round pieces (no tapers or curves). > Adjustable bed must be set level. Position support following behind the > cutter when milling stock round. Position support in front of the cutter > when milling spirals. > > > > Ray > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com?utm_medium=email_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com?utm_medium=email_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamenta
Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
So, where are located? LOL On Sun, Nov 29, 2020 at 9:24 PM wrote: > I was an engineer machinist for over 20 years > > > > Bill > > > > *From:* legacy-ornamental-mills@googlegroups.com < > legacy-ornamental-mills@googlegroups.com> *On Behalf Of *Ray Leaman > *Sent:* Monday, 30 November 2020 1:13 PM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: My 1200 - Accessories: Thin Stock Support and Thin Stock > Follower > > > > I know. Sounds like you got the talent to make one yourself. > > > > On Sun, Nov 29, 2020 at 8:37 PM Tim Ziegler wrote: > > Yea just kidding around Ray. > > I will find one. or make one. > > Kind Regards, > > > > Timothy J. Ziegler > > Ziegler WoodWork & Specialty > > 14171 160th Ave. > > Foreston MN 56330 > > > > 320-294-5798 shop > > 320-630-2243 cell > > > > > > On Sun, Nov 29, 2020 at 4:59 PM Ray Leaman wrote: > > Will do but don't hold your breath too long Tim. As you say, this stuff > is hard to come by. > > > > On Sun, Nov 29, 2020 at 1:55 PM Tim Ziegler wrote: > > wow you ever decide you don't have a use for that I've been looking for > since I bought my LOM. > > The thin Stock Follower that is. > > > Kind Regards, > > > > Timothy J. Ziegler > > Ziegler WoodWork & Specialty > > 14171 160th Ave. > > Foreston MN 56330 > > > > 320-294-5798 shop > > 320-630-2243 cell > > > > > > On Sun, Nov 29, 2020 at 11:15 AM Ray Leaman wrote: > > New in the box (NIB) > > > > Thin Stock Support: Mounts to the underside of the adjustable bed rail > with 2 - 90 degree mounting brackets, and supports material while milling > thin stock between 5/8" and 1 7/8 " thick. > > > > Thin Stock Follower: Mounts to the router carriage. The vinyl dust > shields need to be removed to mount the follower. > > Can only be used on straight round pieces (no tapers or curves). > Adjustable bed must be set level. Position support following behind the > cutter when milling stock round. Position support in front of the cutter > when milling spirals. > > > > Ray > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com?utm_medium=email_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com?utm_medium=email_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com?utm_medium=email_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLF2PKTCHTq7y-uSCi1AaaPx813cGx8Pt7b%2BwMpMdsQzLw%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLF2PKTCHTq7y-uSCi1AaaPx813cGx8Pt7b%2BwMpMdsQzLw%40mail.gmail.com?utm_medium=email_source=footer> > . > > -- > You received this message
Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
I was originally trained as a wood and metal patternmaker. Along the way somewhere I moved more into woodworking and did not include metalworking in my shop planning. Metal fabrication with these mills would definitely be a plus. I may need to develop a relationship with a local machine shop. On Sun, Nov 29, 2020 at 9:16 PM Tim Ziegler wrote: > Where there's a will there's a way right. > What I can't make my Brother can do. He's big into metal work of all > kinds. > > Kind Regards, > > Timothy J. Ziegler > Ziegler WoodWork & Specialty > 14171 160th Ave. > Foreston MN 56330 > > 320-294-5798 shop > 320-630-2243 cell > > > On Sun, Nov 29, 2020 at 8:13 PM Ray Leaman wrote: > >> I know. Sounds like you got the talent to make one yourself. >> >> On Sun, Nov 29, 2020 at 8:37 PM Tim Ziegler >> wrote: >> >>> Yea just kidding around Ray. >>> I will find one. or make one. >>> Kind Regards, >>> >>> Timothy J. Ziegler >>> Ziegler WoodWork & Specialty >>> 14171 160th Ave. >>> Foreston MN 56330 >>> >>> 320-294-5798 shop >>> 320-630-2243 cell >>> >>> >>> On Sun, Nov 29, 2020 at 4:59 PM Ray Leaman wrote: >>> >>>> Will do but don't hold your breath too long Tim. As you say, this >>>> stuff is hard to come by. >>>> >>>> On Sun, Nov 29, 2020 at 1:55 PM Tim Ziegler >>>> wrote: >>>> >>>>> wow you ever decide you don't have a use for that I've been looking >>>>> for since I bought my LOM. >>>>> The thin Stock Follower that is. >>>>> >>>>> Kind Regards, >>>>> >>>>> Timothy J. Ziegler >>>>> Ziegler WoodWork & Specialty >>>>> 14171 160th Ave. >>>>> Foreston MN 56330 >>>>> >>>>> 320-294-5798 shop >>>>> 320-630-2243 cell >>>>> >>>>> >>>>> On Sun, Nov 29, 2020 at 11:15 AM Ray Leaman wrote: >>>>> >>>>>> New in the box (NIB) >>>>>> >>>>>> Thin Stock Support: Mounts to the underside of the adjustable bed >>>>>> rail with 2 - 90 degree mounting brackets, and supports material while >>>>>> milling thin stock between 5/8" and 1 7/8 " thick. >>>>>> >>>>>> Thin Stock Follower: Mounts to the router carriage. The vinyl dust >>>>>> shields need to be removed to mount the follower. >>>>>> Can only be used on straight round pieces (no tapers or curves). >>>>>> Adjustable bed must be set level. Position support following behind the >>>>>> cutter when milling stock round. Position support in front of the cutter >>>>>> when milling spirals. >>>>>> >>>>>> Ray >>>>>> >>>>>> -- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "Legacy Ornamental Mills" group. >>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>> send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com >>>>>> . >>>>>> To view this discussion on the web visit >>>>>> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com >>>>>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com?utm_medium=email_source=footer> >>>>>> . >>>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "Legacy Ornamental Mills" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >>>>> To view this discussion on the web visit >>>>> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com >>>>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com?utm_medium=email_source=footer> >>>>> . >>>>> >>>> -- >>>> You received this message because you are subscribed to the Google &g
RE: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
No I made my own styles Bill From: legacy-ornamental-mills@googlegroups.com On Behalf Of Tim Ziegler Sent: Monday, 30 November 2020 1:26 PM To: legacy-ornamental-mills@googlegroups.com Subject: Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower Did you make your own Bill? Angle bracket style Vertical vise. Or are you referring to the sylus's Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sun, Nov 29, 2020 at 8:24 PM mailto:bulke...@mmnet.com.au> > wrote: I was an engineer machinist for over 20 years Bill From: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> mailto:legacy-ornamental-mills@googlegroups.com> > On Behalf Of Ray Leaman Sent: Monday, 30 November 2020 1:13 PM To: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> Subject: Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower I know. Sounds like you got the talent to make one yourself. On Sun, Nov 29, 2020 at 8:37 PM Tim Ziegler mailto:timjzieg...@gmail.com> > wrote: Yea just kidding around Ray. I will find one. or make one. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sun, Nov 29, 2020 at 4:59 PM Ray Leaman mailto:view...@gmail.com> > wrote: Will do but don't hold your breath too long Tim. As you say, this stuff is hard to come by. On Sun, Nov 29, 2020 at 1:55 PM Tim Ziegler mailto:timjzieg...@gmail.com> > wrote: wow you ever decide you don't have a use for that I've been looking for since I bought my LOM. The thin Stock Follower that is. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sun, Nov 29, 2020 at 11:15 AM Ray Leaman mailto:view...@gmail.com> > wrote: New in the box (NIB) Thin Stock Support: Mounts to the underside of the adjustable bed rail with 2 - 90 degree mounting brackets, and supports material while milling thin stock between 5/8" and 1 7/8 " thick. Thin Stock Follower: Mounts to the router carriage. The vinyl dust shields need to be removed to mount the follower. Can only be used on straight round pieces (no tapers or curves). Adjustable bed must be set level. Position support following behind the cutter when milling stock round. Position support in front of the cutter when milling spirals. Ray -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com?utm_medium=email_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com?utm_medium=email_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com?utm_medium=email_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroup
Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
Did you make your own Bill? Angle bracket style Vertical vise. Or are you referring to the sylus's Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sun, Nov 29, 2020 at 8:24 PM wrote: > I was an engineer machinist for over 20 years > > > > Bill > > > > *From:* legacy-ornamental-mills@googlegroups.com < > legacy-ornamental-mills@googlegroups.com> *On Behalf Of *Ray Leaman > *Sent:* Monday, 30 November 2020 1:13 PM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: My 1200 - Accessories: Thin Stock Support and Thin Stock > Follower > > > > I know. Sounds like you got the talent to make one yourself. > > > > On Sun, Nov 29, 2020 at 8:37 PM Tim Ziegler wrote: > > Yea just kidding around Ray. > > I will find one. or make one. > > Kind Regards, > > > > Timothy J. Ziegler > > Ziegler WoodWork & Specialty > > 14171 160th Ave. > > Foreston MN 56330 > > > > 320-294-5798 shop > > 320-630-2243 cell > > > > > > On Sun, Nov 29, 2020 at 4:59 PM Ray Leaman wrote: > > Will do but don't hold your breath too long Tim. As you say, this stuff > is hard to come by. > > > > On Sun, Nov 29, 2020 at 1:55 PM Tim Ziegler wrote: > > wow you ever decide you don't have a use for that I've been looking for > since I bought my LOM. > > The thin Stock Follower that is. > > > Kind Regards, > > > > Timothy J. Ziegler > > Ziegler WoodWork & Specialty > > 14171 160th Ave. > > Foreston MN 56330 > > > > 320-294-5798 shop > > 320-630-2243 cell > > > > > > On Sun, Nov 29, 2020 at 11:15 AM Ray Leaman wrote: > > New in the box (NIB) > > > > Thin Stock Support: Mounts to the underside of the adjustable bed rail > with 2 - 90 degree mounting brackets, and supports material while milling > thin stock between 5/8" and 1 7/8 " thick. > > > > Thin Stock Follower: Mounts to the router carriage. The vinyl dust > shields need to be removed to mount the follower. > > Can only be used on straight round pieces (no tapers or curves). > Adjustable bed must be set level. Position support following behind the > cutter when milling stock round. Position support in front of the cutter > when milling spirals. > > > > Ray > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com?utm_medium=email_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com?utm_medium=email_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com?utm_medium=email_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLF2PKTCHTq7y-uSCi1AaaPx813cGx8Pt7b%2BwMpMdsQzLw%40mail.gmail.com &g
Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
I know. Sounds like you got the talent to make one yourself. On Sun, Nov 29, 2020 at 8:37 PM Tim Ziegler wrote: > Yea just kidding around Ray. > I will find one. or make one. > Kind Regards, > > Timothy J. Ziegler > Ziegler WoodWork & Specialty > 14171 160th Ave. > Foreston MN 56330 > > 320-294-5798 shop > 320-630-2243 cell > > > On Sun, Nov 29, 2020 at 4:59 PM Ray Leaman wrote: > >> Will do but don't hold your breath too long Tim. As you say, this stuff >> is hard to come by. >> >> On Sun, Nov 29, 2020 at 1:55 PM Tim Ziegler >> wrote: >> >>> wow you ever decide you don't have a use for that I've been looking for >>> since I bought my LOM. >>> The thin Stock Follower that is. >>> >>> Kind Regards, >>> >>> Timothy J. Ziegler >>> Ziegler WoodWork & Specialty >>> 14171 160th Ave. >>> Foreston MN 56330 >>> >>> 320-294-5798 shop >>> 320-630-2243 cell >>> >>> >>> On Sun, Nov 29, 2020 at 11:15 AM Ray Leaman wrote: >>> >>>> New in the box (NIB) >>>> >>>> Thin Stock Support: Mounts to the underside of the adjustable bed rail >>>> with 2 - 90 degree mounting brackets, and supports material while milling >>>> thin stock between 5/8" and 1 7/8 " thick. >>>> >>>> Thin Stock Follower: Mounts to the router carriage. The vinyl dust >>>> shields need to be removed to mount the follower. >>>> Can only be used on straight round pieces (no tapers or curves). >>>> Adjustable bed must be set level. Position support following behind the >>>> cutter when milling stock round. Position support in front of the cutter >>>> when milling spirals. >>>> >>>> Ray >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "Legacy Ornamental Mills" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >>>> To view this discussion on the web visit >>>> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com >>>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com?utm_medium=email_source=footer> >>>> . >>>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com >>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com?utm_medium=email_source=footer> >>> . >>> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com >> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com?utm_medium=email_source=footer> >> . >> > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLF2PKTCHTq7y-uSCi1AaaPx813cGx8Pt7b%2BwMpMdsQzLw%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLF2PKTCHTq7y-uSCi1AaaPx813cGx8Pt7b%2BwMpMdsQzLw%40mail.gmail.com?utm_medium=email_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdLq3mJ1JehNOTt2ueVBOSc%2BwOr-txB0gMYqMJqC%2BUSGKQ%40mail.gmail.com.
Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
Yea just kidding around Ray. I will find one. or make one. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sun, Nov 29, 2020 at 4:59 PM Ray Leaman wrote: > Will do but don't hold your breath too long Tim. As you say, this stuff > is hard to come by. > > On Sun, Nov 29, 2020 at 1:55 PM Tim Ziegler wrote: > >> wow you ever decide you don't have a use for that I've been looking for >> since I bought my LOM. >> The thin Stock Follower that is. >> >> Kind Regards, >> >> Timothy J. Ziegler >> Ziegler WoodWork & Specialty >> 14171 160th Ave. >> Foreston MN 56330 >> >> 320-294-5798 shop >> 320-630-2243 cell >> >> >> On Sun, Nov 29, 2020 at 11:15 AM Ray Leaman wrote: >> >>> New in the box (NIB) >>> >>> Thin Stock Support: Mounts to the underside of the adjustable bed rail >>> with 2 - 90 degree mounting brackets, and supports material while milling >>> thin stock between 5/8" and 1 7/8 " thick. >>> >>> Thin Stock Follower: Mounts to the router carriage. The vinyl dust >>> shields need to be removed to mount the follower. >>> Can only be used on straight round pieces (no tapers or curves). >>> Adjustable bed must be set level. Position support following behind the >>> cutter when milling stock round. Position support in front of the cutter >>> when milling spirals. >>> >>> Ray >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com >>> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com?utm_medium=email_source=footer> >>> . >>> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com >> <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com?utm_medium=email_source=footer> >> . >> > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdK67LPHMqhw7jfZ1GzbbAEDPtMRzJ21f%2B%3DruLyn%2BRexjA%40mail.gmail.com?utm_medium=email_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLF2PKTCHTq7y-uSCi1AaaPx813cGx8Pt7b%2BwMpMdsQzLw%40mail.gmail.com.
Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
Seems someone on this site raised an objection question about copying
materials for broad distribution. Doing it as an individual seems o.k. so
that 's what I did.
On Sun, Nov 29, 2020 at 12:34 PM M.W.Foscue wrote:
> Ray,
> The gift that keeps on giving! Can't wait for the next thing you post!
> Since all these are NIB - you seem to have all the paperwork that they
> came with - instruction sheet(s), etc.
> When you get the chance, would you please scan all of them and put them in
> an email to The Group?
> Scanned, they will not be as big of a file vs photos would; and their
> clarity should be as good as the originals.
> I imagine many of us have acquired our Mills like you did - buying them
> from the original (or follow-on) owners. Probably in many cases, the
> Instruction sheets were not included in that purchase. They were probably
> filed in binders by owner - but since binders were elsewhere in the shop or
> house, did not go out the door with the Mill. {:-(
>
> Thanks again.
> Mac
> --
>
> -Original Message-
> From: Ray Leaman
> Sent: Nov 29, 2020 12:14 PM
> To: legacy-ornamental-mills@googlegroups.com
> Subject: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
>
> New in the box (NIB)
>
> Thin Stock Support: Mounts to the underside of the adjustable bed rail
> with 2 - 90 degree mounting brackets, and supports material while milling
> thin stock between 5/8" and 1 7/8 " thick.
>
> Thin Stock Follower: Mounts to the router carriage. The vinyl dust
> shields need to be removed to mount the follower.
> Can only be used on straight round pieces (no tapers or curves).
> Adjustable bed must be set level. Position support following behind the
> cutter when milling stock round. Position support in front of the cutter
> when milling spirals.
>
> Ray
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/legacy-ornamental-mills/197161389.1410.1606671273194%40wamui-charming.atl.sa.earthlink.net
> <https://groups.google.com/d/msgid/legacy-ornamental-mills/197161389.1410.1606671273194%40wamui-charming.atl.sa.earthlink.net?utm_medium=email_source=footer>
> .
>
--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCdJtCiitvZA0UO9WQYr5%2BcEaetX4HKgxtB4GwfR%2B5p_FKQ%40mail.gmail.com.
RE: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
You really lucked out ray you got it all some of us it took years to accumulate all those extras some are still looking congrats Bill From: legacy-ornamental-mills@googlegroups.com On Behalf Of Ray Leaman Sent: Monday, 30 November 2020 4:15 AM To: legacy-ornamental-mills@googlegroups.com Subject: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower New in the box (NIB) Thin Stock Support: Mounts to the underside of the adjustable bed rail with 2 - 90 degree mounting brackets, and supports material while milling thin stock between 5/8" and 1 7/8 " thick. Thin Stock Follower: Mounts to the router carriage. The vinyl dust shields need to be removed to mount the follower. Can only be used on straight round pieces (no tapers or curves). Adjustable bed must be set level. Position support following behind the cutter when milling stock round. Position support in front of the cutter when milling spirals. Ray -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com?utm_medium=email_source=footer> . -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/001301d6c693%24b9ceac70%242d6c0550%24%40mmnet.com.au.
Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
wow you ever decide you don't have a use for that I've been looking for since I bought my LOM. The thin Stock Follower that is. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sun, Nov 29, 2020 at 11:15 AM Ray Leaman wrote: > New in the box (NIB) > > Thin Stock Support: Mounts to the underside of the adjustable bed rail > with 2 - 90 degree mounting brackets, and supports material while milling > thin stock between 5/8" and 1 7/8 " thick. > > Thin Stock Follower: Mounts to the router carriage. The vinyl dust > shields need to be removed to mount the follower. > Can only be used on straight round pieces (no tapers or curves). > Adjustable bed must be set level. Position support following behind the > cutter when milling stock round. Position support in front of the cutter > when milling spirals. > > Ray > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAEnRCd%2BKUpdBNTHPpNTa5YL9H6r86Xp4UYKUC6DcZQVDCTaLQw%40mail.gmail.com?utm_medium=email_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqrFoLdg8b5uwoSSPcaCWvE2c0bg5eQHZhQjVFsYTpMg%40mail.gmail.com.
Re: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
Ray,The gift that keeps on giving! Can't wait for the next thing you post!Since all these are NIB - you seem to have all the paperwork that they came with - instruction sheet(s), etc.When you get the chance, would you please scan all of them and put them in an email to The Group?Scanned, they will not be as big of a file vs photos would; and their clarity should be as good as the originals.I imagine many of us have acquired our Mills like you did - buying them from the original (or follow-on) owners. Probably in many cases, the Instruction sheets were not included in that purchase. They were probably filed in binders by owner - but since binders were elsewhere in the shop or house, did not go out the door with the Mill. {:-(Thanks again.Mac-Original Message-
From: Ray Leaman
Sent: Nov 29, 2020 12:14 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: My 1200 - Accessories: Thin Stock Support and Thin Stock Follower
New in the box (NIB)Thin Stock Support: Mounts to the underside of the adjustable bed rail with 2 - 90 degree mounting brackets, and supports material while milling thin stock between 5/8" and 1 7/8 " thick.Thin Stock Follower: Mounts to the router carriage. The vinyl dust shields need to be removed to mount the follower.Can only be used on straight round pieces (no tapers or curves). Adjustable bed must be set level. Position support following behind the cutter when milling stock round. Position support in front of the cutter when milling spirals.Ray
--
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/197161389.1410.1606671273194%40wamui-charming.atl.sa.earthlink.net.
Re: Thin Stock support-thin stock follower-vertical Bench Vise
I wish you Luck Tim. I will keep my eyes open for you...Take care. C.A.G. On Tuesday, June 4, 2019, 8:12:23 AM EDT, Tim Ziegler wrote: STILL LOOKING! For any of you out there that have these parts and are possibly thinking you don't use them, I'd be interested in them.I know I posted this before, but I really could use the: Thin Stock SupportThin Stock FollowerVertical Bench Vise Wouldn't mind finding a 4X Gear Upgrade too. I am really trying to zero in on more uses for my LOM 1200 for my business and of course to play a bit too. Thanks Kind regards, Tim of ZWW -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/6c9d9dd4-1ed5-4661-bee6-0e883a8a0455%40googlegroups.com. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/391277082.1315833.1559650711791%40mail.yahoo.com. For more options, visit https://groups.google.com/d/optout.
Thin Stock support-thin stock follower-vertical Bench Vise
STILL LOOKING! For any of you out there that have these parts and are possibly thinking you don't use them, I'd be interested in them. I know I posted this before, but I really could use the: Thin Stock Support Thin Stock Follower Vertical Bench Vise Wouldn't mind finding a 4X Gear Upgrade too. I am really trying to zero in on more uses for my LOM 1200 for my business and of course to play a bit too. Thanks Kind regards, Tim of ZWW -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/6c9d9dd4-1ed5-4661-bee6-0e883a8a0455%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
Re: Thin-stock follower & Thin Stock Support HOT
That would be great! Thanks Bill Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Thu, May 2, 2019 at 7:36 AM Bill Bulkeley wrote: > I can take a few measurements for you if it helps if you can’t find one > > > > Bill > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Tim Ziegler > *Sent:* Thursday, 2 May 2019 9:30 PM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: Thin-stock follower & Thin Stock Support HOT > > > > Thanks Bill. Yea I did start on one and then messed it up. I had some nice > UHMF or UHMW or what ever abbreviations are. Its that self healing white > plastic. > > Awesome stuff and I only had so much of it. I think I was in to big of > hurry to complete it. But we never do stuff like that do we. lol > > No neither of the parts look to hard to make. I have a brother with a full > machining shop and I'd guess I may just have him chuck it up on his mill if > I don't find one. > > thanks Bill. > > > Kind Regards, > > > > Timothy J. Ziegler > > Ziegler WoodWork & Specialty > > 14171 160th Ave. > > Foreston MN 56330 > > > > 320-294-5798 shop > > 320-630-2243 cell > > > > > > On Wed, May 1, 2019 at 11:25 PM Bill Bulkeley > wrote: > > I wish you luck with your search Tim I have the thin stock support not for > sale before you ask I too would like the legacy thin stock follower but I > will most likely have to make it. > > If you have some rail the rest of the thin stock support is just 2 blocks > of delrin with a 90 degree v cut in it > > > > Bill > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Tim Ziegler > *Sent:* Thursday, 2 May 2019 1:04 PM > *To:* Legacy Ornamental Mills > *Subject:* Re: Thin-stock follower & Thin Stock Support HOT > > > > I'm still looking for these parts. > > > > Kind regards, > > > > Tim of ZWW > > On Monday, February 11, 2019 at 8:06:00 AM UTC-6, Tim Ziegler wrote: > > Good morning fellow LOM & WC people. > > > > Now that I found the Rotary table I was looking for I am looking for the > Thin-Stock follower and Thin Stock Support. > > > > I know selling parts from units is not always easy but I bought my LOM > 1200 to further my business opportunities and need to move forward. > > Does anyone have these items for sale or has anyone made after market > parts for them? I did see an idea on the "Turn Around" site. But I want the > > real thing. this is not a part I can get through Legacy. I've tried. > > > > Thanks everyone. > > > > Kind regards, > > > > Tim of ZWW > > > > Tim J. Ziegler > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > > > > <http://www.avg.com/email-signature?utm_medium=email_source=link_campaign=sig-email_content=emailclient> > > Virus-free. www.avg.com > <http://www.avg.com/email-signature?utm_medium=email_source=link_campaign=sig-email_content=emailclient> > > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. >
Re: Thin-stock follower & Thin Stock Support HOT
Thanks Bill. Yea I did start on one and then messed it up. I had some nice UHMF or UHMW or what ever abbreviations are. Its that self healing white plastic. Awesome stuff and I only had so much of it. I think I was in to big of hurry to complete it. But we never do stuff like that do we. lol No neither of the parts look to hard to make. I have a brother with a full machining shop and I'd guess I may just have him chuck it up on his mill if I don't find one. thanks Bill. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Wed, May 1, 2019 at 11:25 PM Bill Bulkeley wrote: > I wish you luck with your search Tim I have the thin stock support not for > sale before you ask I too would like the legacy thin stock follower but I > will most likely have to make it. > > If you have some rail the rest of the thin stock support is just 2 blocks > of delrin with a 90 degree v cut in it > > > > Bill > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Tim Ziegler > *Sent:* Thursday, 2 May 2019 1:04 PM > *To:* Legacy Ornamental Mills > *Subject:* Re: Thin-stock follower & Thin Stock Support HOT > > > > I'm still looking for these parts. > > > > Kind regards, > > > > Tim of ZWW > > On Monday, February 11, 2019 at 8:06:00 AM UTC-6, Tim Ziegler wrote: > > Good morning fellow LOM & WC people. > > > > Now that I found the Rotary table I was looking for I am looking for the > Thin-Stock follower and Thin Stock Support. > > > > I know selling parts from units is not always easy but I bought my LOM > 1200 to further my business opportunities and need to move forward. > > Does anyone have these items for sale or has anyone made after market > parts for them? I did see an idea on the "Turn Around" site. But I want the > > real thing. this is not a part I can get through Legacy. I've tried. > > > > Thanks everyone. > > > > Kind regards, > > > > Tim of ZWW > > > > Tim J. Ziegler > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > > > > <http://www.avg.com/email-signature?utm_medium=email_source=link_campaign=sig-email_content=emailclient> > > Virus-free. www.avg.com > <http://www.avg.com/email-signature?utm_medium=email_source=link_campaign=sig-email_content=emailclient> > > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Thin-stock follower & Thin Stock Support HOT
Thank you Sir that should help a lot. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Wed, May 1, 2019 at 11:17 PM 'Curt George' via Legacy Ornamental Mills < legacy-ornamental-mills@googlegroups.com> wrote: > Hello Tim > I wish you luck finding those parts you are looking for. > Perhaps it would be a better question for the group ,being , if anyone > could make the parts in question? Or, > If any one owns these parts, can you post them to the group. > I have only seen the photo's in Legacy catalog, No first hand experiences > with this parts.(for me.) > Perhaps a few photo's could help clear out some of the cob-webs on this > topic ? ;-) > > Here are some pictures that Tim is looking for... > > C.A.G. > > > > > > <https://web.archive.org/web/20061017023530/http://www.legacywoodworking.com/products.cfm?product=78> > [image: Thin Stock Follower] > Thin Stock Follower > <https://web.archive.org/web/20061017023530/http://www.legacywoodworking.com/products.cfm?product=99> > > Home > <https://web.archive.org/web/20050303233255/http://www.legacywoodworking.com/index.cfm> > > Products > <https://web.archive.org/web/20050303233255/http://www.legacywoodworking.com/productList.cfm> > > Mill Accessories > <https://web.archive.org/web/20050303233255/http://www.legacywoodworking.com/productList.cfm?type=2> > > > Thin Stock Support > > Thin Stock Support > (part no. LTHINSTK) > > > [image: Thin Stock Support] > > *$89.00* > > Supports round stock less than 2" diameter to eliminate chatter when > milling spirals, flutes etc. > > > On Wednesday, May 1, 2019, 11:03:43 PM EDT, Tim Ziegler < > timjzieg...@gmail.com> wrote: > > > I'm still looking for these parts. > > Kind regards, > > Tim of ZWW > > On Monday, February 11, 2019 at 8:06:00 AM UTC-6, Tim Ziegler wrote: > > Good morning fellow LOM & WC people. > > Now that I found the Rotary table I was looking for I am looking for the > Thin-Stock follower and Thin Stock Support. > > I know selling parts from units is not always easy but I bought my LOM > 1200 to further my business opportunities and need to move forward. > Does anyone have these items for sale or has anyone made after market > parts for them? I did see an idea on the "Turn Around" site. But I want the > real thing. this is not a part I can get through Legacy. I've tried. > > Thanks everyone. > > Kind regards, > > Tim of ZWW > > Tim J. Ziegler > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
RE: Thin-stock follower & Thin Stock Support HOT
I wish you luck with your search Tim I have the thin stock support not for sale before you ask I too would like the legacy thin stock follower but I will most likely have to make it. If you have some rail the rest of the thin stock support is just 2 blocks of delrin with a 90 degree v cut in it Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Tim Ziegler Sent: Thursday, 2 May 2019 1:04 PM To: Legacy Ornamental Mills Subject: Re: Thin-stock follower & Thin Stock Support HOT I'm still looking for these parts. Kind regards, Tim of ZWW On Monday, February 11, 2019 at 8:06:00 AM UTC-6, Tim Ziegler wrote: Good morning fellow LOM & WC people. Now that I found the Rotary table I was looking for I am looking for the Thin-Stock follower and Thin Stock Support. I know selling parts from units is not always easy but I bought my LOM 1200 to further my business opportunities and need to move forward. Does anyone have these items for sale or has anyone made after market parts for them? I did see an idea on the "Turn Around" site. But I want the real thing. this is not a part I can get through Legacy. I've tried. Thanks everyone. Kind regards, Tim of ZWW Tim J. Ziegler -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. <http://www.avg.com/email-signature?utm_medium=email_source=link_campaign=sig-email_content=emailclient> Virus-free. <http://www.avg.com/email-signature?utm_medium=email_source=link_campaign=sig-email_content=emailclient> www.avg.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Thin-stock follower & Thin Stock Support HOT
Hello TimI wish you luck finding those parts you are looking for. Perhaps it would be a better question for the group ,being , if anyone could make the parts in question? Or,If any one owns these parts, can you post them to the group. I have only seen the photo's in Legacy catalog, No first hand experiences with this parts.(for me.) Perhaps a few photo's could help clear out some of the cob-webs on this topic ? ;-) Here are some pictures that Tim is looking for... C.A.G. | | | | | | Thin Stock Follower | | Home > Products > Mill Accessories > Thin Stock Support | Thin Stock Support (part no. LTHINSTK) $89.00 Supports round stock less than 2" diameter to eliminate chatter when milling spirals, flutes etc. | | On Wednesday, May 1, 2019, 11:03:43 PM EDT, Tim Ziegler wrote: I'm still looking for these parts. Kind regards, Tim of ZWW On Monday, February 11, 2019 at 8:06:00 AM UTC-6, Tim Ziegler wrote: Good morning fellow LOM & WC people. Now that I found the Rotary table I was looking for I am looking for the Thin-Stock follower and Thin Stock Support. I know selling parts from units is not always easy but I bought my LOM 1200 to further my business opportunities and need to move forward.Does anyone have these items for sale or has anyone made after market parts for them? I did see an idea on the "Turn Around" site. But I want the real thing. this is not a part I can get through Legacy. I've tried. Thanks everyone. Kind regards, Tim of ZWW Tim J. Ziegler -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Thin-stock follower & Thin Stock Support HOT
I'm still looking for these parts. Kind regards, Tim of ZWW On Monday, February 11, 2019 at 8:06:00 AM UTC-6, Tim Ziegler wrote: > > Good morning fellow LOM & WC people. > > Now that I found the Rotary table I was looking for I am looking for the > Thin-Stock follower and Thin Stock Support. > > I know selling parts from units is not always easy but I bought my LOM > 1200 to further my business opportunities and need to move forward. > Does anyone have these items for sale or has anyone made after market > parts for them? I did see an idea on the "Turn Around" site. But I want the > real thing. this is not a part I can get through Legacy. I've tried. > > Thanks everyone. > > Kind regards, > > Tim of ZWW > > Tim J. Ziegler > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Prices on thin stock follower,thin stock support and vertical Bench vise
Call and ask for Cindy, she takes care of the parts of these machines. Not everything is available and it takes a bit. But I just received my brand new sets last week. So give her a call and see where it goes. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Wed, Mar 20, 2019 at 10:12 AM Ryan Hellmer wrote: > I thought LOM was no longer supporting any of the manual machines. Where > could I order a set? The LWMCNC site pretty clearly says they no longer > support. - Ryan > > Sent from my iPhone > > On Mar 20, 2019, at 10:01 AM, Tim Ziegler wrote: > > Ok Bill I will ck on that as well. > Kind Regards, > > Timothy J. Ziegler > Ziegler WoodWork & Specialty > 14171 160th Ave. > Foreston MN 56330 > > 320-294-5798 shop > 320-630-2243 cell > > > On Wed, Mar 20, 2019 at 9:49 AM Bill Bulkeley > wrote: > >> Tim i would be interested in a Linear Drive Motor if not too expensive >> >> >> >> Bill >> >> >> >> *From:* legacy-ornamental-mills@googlegroups.com [mailto: >> legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Tim Ziegler >> *Sent:* Thursday, 21 March 2019 12:39 AM >> *To:* legacy-ornamental-mills@googlegroups.com >> *Subject:* Re: Prices on thin stock follower,thin stock support and >> vertical Bench vise >> >> >> >> I'll let him know Ryan. If not these can still be ordered from LOM too >> >> >> >> >> >> On Wed, Mar 20, 2019, 7:46 AM Ryan Hellmer >> wrote: >> >> I’d be interested in a 2x multiplier gear set. - Ryan >> >> Sent from my iPhone >> >> >> On Mar 20, 2019, at 7:13 AM, Tim Ziegler wrote: >> >> Curtis I have a guy that is parting out a 1000 steely. >> >> Can you send me copies of all the prices you have like you sent me >> earlier? >> >> >> >> >> Kind Regards, >> >> >> >> Timothy J. Ziegler >> >> Ziegler WoodWork & Specialty >> >> 14171 160th Ave. >> >> Foreston MN 56330 >> >> >> >> 320-294-5798 shop >> >> 320-630-2243 cell >> >> >> >> >> >> On Mon, Mar 18, 2019 at 7:22 AM 'Curt George' via Legacy Ornamental Mills >> wrote: >> >> Hello Tim >> >> This is what I found. >> >> I hope it helps? >> >> >> >> C.A.G. >> >> >> >> >> >> >> >> Thin Stock Support >> >> (part no. LTHINSTK) >> >> >> >> [image: Thin Stock Support] >> >> >> >> *$99.00* [image: Add To Cart] >> <https://web.archive.org/web/20120505180504/http:/legacywoodworking.com/cart.cfm?add=15> >> >> >> >> *Projects* >> >> * featuring the Vertical Vise*: >> >>- Table >> >> <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/galleryItem.cfm?project=90> >> >> Home >> <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/index.cfm> >> > Products >> <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/productList.cfm> >> > Mill Accessories >> <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/productList.cfm?type=2> >> > >> Vertical Vise >> >> Cart : 1 items - $89.00 View >> <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/cart.cfm> >> >> >> >> Vertical Vise >> >> (part no. LVISEVERT10) >> >> >> >> [image: Vertical Vise] >> >> >> >> *$119.00* [image: Add To Cart] >> <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/cart.cfm?add=17> >> >> >> >> >> >> [image: Thin Stock Follower] >> Thin Stock Follower >> <https://web.archive.org/web/20101009040546/http:/legacywoodworking.com/products.cfm?product=99> >> >> ???$$$??? There is not price on this, It only shows up on three catolog >> listings and none have a price on them. >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> On Monday, March 18, 2019, 7:23:43 AM EDT, Tim Ziegler < >> timjzieg...@gmail.com> wrote: >> >> >> >> >> >> Good morning All, >> >> >> >> Does any
Re: Prices on thin stock follower,thin stock support and vertical Bench vise
I thought LOM was no longer supporting any of the manual machines. Where could I order a set? The LWMCNC site pretty clearly says they no longer support. - Ryan Sent from my iPhone > On Mar 20, 2019, at 10:01 AM, Tim Ziegler wrote: > > Ok Bill I will ck on that as well. > Kind Regards, > > Timothy J. Ziegler > Ziegler WoodWork & Specialty > 14171 160th Ave. > Foreston MN 56330 > > 320-294-5798 shop > 320-630-2243 cell > > >> On Wed, Mar 20, 2019 at 9:49 AM Bill Bulkeley wrote: >> Tim i would be interested in a Linear Drive Motor if not too expensive >> >> >> >> Bill >> >> >> >> From: legacy-ornamental-mills@googlegroups.com >> [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Tim Ziegler >> Sent: Thursday, 21 March 2019 12:39 AM >> To: legacy-ornamental-mills@googlegroups.com >> Subject: Re: Prices on thin stock follower,thin stock support and vertical >> Bench vise >> >> >> >> I'll let him know Ryan. If not these can still be ordered from LOM too >> >> >> >> >> >> On Wed, Mar 20, 2019, 7:46 AM Ryan Hellmer wrote: >> >> I’d be interested in a 2x multiplier gear set. - Ryan >> >> Sent from my iPhone >> >> >> On Mar 20, 2019, at 7:13 AM, Tim Ziegler wrote: >> >> Curtis I have a guy that is parting out a 1000 steely. >> >> Can you send me copies of all the prices you have like you sent me earlier? >> >> >> >> >> >> Kind Regards, >> >> >> >> Timothy J. Ziegler >> >> Ziegler WoodWork & Specialty >> >> 14171 160th Ave. >> >> Foreston MN 56330 >> >> >> >> 320-294-5798 shop >> >> 320-630-2243 cell >> >> >> >> >> >> On Mon, Mar 18, 2019 at 7:22 AM 'Curt George' via Legacy Ornamental Mills >> wrote: >> >> Hello Tim >> >> This is what I found. >> >> I hope it helps? >> >> >> >> C.A.G. >> >> >> >> >> >> >> >> Thin Stock Support >> >> (part no. LTHINSTK) >> >> >> >> >> >> >> $99.00 >> >> >> >> >> Projects >> featuring the >> Vertical Vise: >> >> Table >> Home > Products > Mill Accessories > Vertical Vise >> >> Cart : 1 items - $89.00 View >> >> >> >> Vertical Vise >> >> (part no. LVISEVERT10) >> >> >> >> >> >> >> $119.00 >> >> >> >> >> >> >> Thin Stock Follower >> >> ???$$$??? There is not price on this, It only shows up on three catolog >> listings and none have a price on them. >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> On Monday, March 18, 2019, 7:23:43 AM EDT, Tim Ziegler >> wrote: >> >> >> >> >> >> Good morning All, >> >> >> >> Does anyone have a price list of the parts that were available for the LOM's >> besides what is listed in the back of the manual. >> >> >> >> I have a lead on some parts I have been looking to purchase for my 1200 LOM >> and need to know what they cost originally to may a fair offer. >> >> >> >> 1. Thin stock follower >> >> >> >> 2. Thin Stock Support >> >> >> >> 3. Vertical Bench Vise >> >> >> >> >> >> Kind regards, >> >> >> >> >> >> Tim of ZWW >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To post to this group, send email to >> legacy-ornamental-mills@googlegroups.com. >> Visit this group at https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this
Re: Prices on thin stock follower,thin stock support and vertical Bench vise
Ok Bill I will ck on that as well. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Wed, Mar 20, 2019 at 9:49 AM Bill Bulkeley wrote: > Tim i would be interested in a Linear Drive Motor if not too expensive > > > > Bill > > > > *From:* legacy-ornamental-mills@googlegroups.com [mailto: > legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Tim Ziegler > *Sent:* Thursday, 21 March 2019 12:39 AM > *To:* legacy-ornamental-mills@googlegroups.com > *Subject:* Re: Prices on thin stock follower,thin stock support and > vertical Bench vise > > > > I'll let him know Ryan. If not these can still be ordered from LOM too > > > > > > On Wed, Mar 20, 2019, 7:46 AM Ryan Hellmer > wrote: > > I’d be interested in a 2x multiplier gear set. - Ryan > > Sent from my iPhone > > > On Mar 20, 2019, at 7:13 AM, Tim Ziegler wrote: > > Curtis I have a guy that is parting out a 1000 steely. > > Can you send me copies of all the prices you have like you sent me earlier? > > > > > Kind Regards, > > > > Timothy J. Ziegler > > Ziegler WoodWork & Specialty > > 14171 160th Ave. > > Foreston MN 56330 > > > > 320-294-5798 shop > > 320-630-2243 cell > > > > > > On Mon, Mar 18, 2019 at 7:22 AM 'Curt George' via Legacy Ornamental Mills < > legacy-ornamental-mills@googlegroups.com> wrote: > > Hello Tim > > This is what I found. > > I hope it helps? > > > > C.A.G. > > > > > > > > Thin Stock Support > > (part no. LTHINSTK) > > > > [image: Thin Stock Support] > > > > *$99.00* [image: Add To Cart] > <https://web.archive.org/web/20120505180504/http:/legacywoodworking.com/cart.cfm?add=15> > > > > *Projects* > > * featuring the Vertical Vise*: > >- Table > > <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/galleryItem.cfm?project=90> > > Home > <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/index.cfm> > > Products > <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/productList.cfm> > > Mill Accessories > <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/productList.cfm?type=2> > > > Vertical Vise > > Cart : 1 items - $89.00 View > <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/cart.cfm> > > > > Vertical Vise > > (part no. LVISEVERT10) > > > > [image: Vertical Vise] > > > > *$119.00* [image: Add To Cart] > <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/cart.cfm?add=17> > > > > > > [image: Thin Stock Follower] > Thin Stock Follower > <https://web.archive.org/web/20101009040546/http:/legacywoodworking.com/products.cfm?product=99> > > ???$$$??? There is not price on this, It only shows up on three catolog > listings and none have a price on them. > > > > > > > > > > > > > > > > > > > > On Monday, March 18, 2019, 7:23:43 AM EDT, Tim Ziegler < > timjzieg...@gmail.com> wrote: > > > > > > Good morning All, > > > > Does anyone have a price list of the parts that were available for the > LOM's besides what is listed in the back of the manual. > > > > I have a lead on some parts I have been looking to purchase for my 1200 > LOM and need to know what they cost originally to may a fair offer. > > > > 1. Thin stock follower > > > > 2. Thin Stock Support > > > > 3. Vertical Bench Vise > > > > > > Kind regards, > > > > > > Tim of ZWW > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. &g
RE: Prices on thin stock follower,thin stock support and vertical Bench vise
Tim i would be interested in a Linear Drive Motor if not too expensive Bill From: legacy-ornamental-mills@googlegroups.com [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Tim Ziegler Sent: Thursday, 21 March 2019 12:39 AM To: legacy-ornamental-mills@googlegroups.com Subject: Re: Prices on thin stock follower,thin stock support and vertical Bench vise I'll let him know Ryan. If not these can still be ordered from LOM too On Wed, Mar 20, 2019, 7:46 AM Ryan Hellmer wrote: I’d be interested in a 2x multiplier gear set. - Ryan Sent from my iPhone On Mar 20, 2019, at 7:13 AM, Tim Ziegler wrote: Curtis I have a guy that is parting out a 1000 steely. Can you send me copies of all the prices you have like you sent me earlier? Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Mon, Mar 18, 2019 at 7:22 AM 'Curt George' via Legacy Ornamental Mills wrote: Hello Tim This is what I found. I hope it helps? C.A.G. Thin Stock Support (part no. LTHINSTK) Thin Stock Support <https://web.archive.org/web/20120505180504im_/http:/legacywoodworking.com/images/product/15.jpg> $99.00 <https://web.archive.org/web/20120505180504/http:/legacywoodworking.com/cart.cfm?add=15> Add To Cart Projects featuring the Vertical Vise: * <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/galleryItem.cfm?project=90> Table <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/index.cfm> Home > <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/productList.cfm> Products > <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/productList.cfm?type=2> Mill Accessories > Vertical Vise Cart : 1 items - $89.00 <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/cart.cfm> View Vertical Vise (part no. LVISEVERT10) Vertical Vise <https://web.archive.org/web/20061017023815im_/http:/www.legacywoodworking.com/images/product/17.jpg> $119.00 <https://web.archive.org/web/20061017023815/http:/www.legacywoodworking.com/cart.cfm?add=17> Add To Cart <https://web.archive.org/web/20101009040546/http:/legacywoodworking.com/products.cfm?product=99> Thin Stock Follower Thin Stock Follower ???$$$??? There is not price on this, It only shows up on three catolog listings and none have a price on them. On Monday, March 18, 2019, 7:23:43 AM EDT, Tim Ziegler wrote: Good morning All, Does anyone have a price list of the parts that were available for the LOM's besides what is listed in the back of the manual. I have a lead on some parts I have been looking to purchase for my 1200 LOM and need to know what they cost originally to may a fair offer. 1. Thin stock follower 2. Thin Stock Support 3. Vertical Bench Vise Kind regards, Tim of ZWW -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options,
Re: Prices on thin stock follower,thin stock support and vertical Bench vise
Hello Timhttps://web.archive.org/web/20041205143900/http://www.legacywoodworking.com/productList.cfm?type=2 OR this one. https://web.archive.org/web/20051025222338/http://www.legacywoodworking.com/productList.cfm?type=2 I hope these help might help? C.A.G. On Wednesday, March 20, 2019, 9:39:42 AM EDT, Tim Ziegler wrote: I'll let him know Ryan. If not these can still be ordered from LOM too On Wed, Mar 20, 2019, 7:46 AM Ryan Hellmer wrote: I’d be interested in a 2x multiplier gear set. - Ryan Sent from my iPhone On Mar 20, 2019, at 7:13 AM, Tim Ziegler wrote: Curtis I have a guy that is parting out a 1000 steely.Can you send me copies of all the prices you have like you sent me earlier? Kind Regards, Timothy J. ZieglerZiegler WoodWork & Specialty14171 160th Ave.Foreston MN 56330 320-294-5798 shop320-630-2243 cell On Mon, Mar 18, 2019 at 7:22 AM 'Curt George' via Legacy Ornamental Mills wrote: Hello TimThis is what I found.I hope it helps? C.A.G. Thin Stock Support (part no. LTHINSTK) $99.00 | Projects featuring the Vertical Vise: - Table | Home > Products > Mill Accessories > Vertical ViseCart : 1 items - $89.00 View | Vertical Vise (part no. LVISEVERT10) $119.00 Thin Stock Follower ???$$$??? There is not price on this, It only shows up on three catolog listings and none have a price on them. | | On Monday, March 18, 2019, 7:23:43 AM EDT, Tim Ziegler wrote: Good morning All, Does anyone have a price list of the parts that were available for the LOM's besides what is listed in the back of the manual. I have a lead on some parts I have been looking to purchase for my 1200 LOM and need to know what they cost originally to may a fair offer. 1. Thin stock follower 2. Thin Stock Support 3. Vertical Bench Vise Kind regards, Tim of ZWW -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Prices on thin stock follower,thin stock support and vertical Bench vise
I’d be interested in a 2x multiplier gear set. - Ryan Sent from my iPhone > On Mar 20, 2019, at 7:13 AM, Tim Ziegler wrote: > > Curtis I have a guy that is parting out a 1000 steely. > Can you send me copies of all the prices you have like you sent me earlier? > > > Kind Regards, > > Timothy J. Ziegler > Ziegler WoodWork & Specialty > 14171 160th Ave. > Foreston MN 56330 > > 320-294-5798 shop > 320-630-2243 cell > > >> On Mon, Mar 18, 2019 at 7:22 AM 'Curt George' via Legacy Ornamental Mills >> wrote: >> Hello Tim >> This is what I found. >> I hope it helps? >> >> C.A.G. >> >> >> >> Thin Stock Support >> >> (part no. LTHINSTK) >> >> >> >> $99.00 >> >> >> >> Projects >> featuring the >> Vertical Vise: >> Table >> Home > Products > Mill Accessories > Vertical Vise >> Cart : 1 items - $89.00 View >> >> Vertical Vise >> >> (part no. LVISEVERT10) >> >> >> >> $119.00 >> >> >> >> Thin Stock Follower >> ???$$$??? There is not price on this, It only shows up on three catolog >> listings and none have a price on them. >> >> >> >> >> >> >> >> >> >> >> On Monday, March 18, 2019, 7:23:43 AM EDT, Tim Ziegler >> wrote: >> >> >> Good morning All, >> >> Does anyone have a price list of the parts that were available for the LOM's >> besides what is listed in the back of the manual. >> >> I have a lead on some parts I have been looking to purchase for my 1200 LOM >> and need to know what they cost originally to may a fair offer. >> >> 1. Thin stock follower >> >> 2. Thin Stock Support >> >> 3. Vertical Bench Vise >> >> >> Kind regards, >> >> >> Tim of ZWW >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To post to this group, send email to >> legacy-ornamental-mills@googlegroups.com. >> Visit this group at https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >> To post to this group, send email to >> legacy-ornamental-mills@googlegroups.com. >> Visit this group at https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to legacy-ornamental-mills@googlegroups.com. > Visit this group at https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Prices on thin stock follower,thin stock support and vertical Bench vise
exactly what I needed thanks Curtis Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Mon, Mar 18, 2019 at 7:22 AM 'Curt George' via Legacy Ornamental Mills < legacy-ornamental-mills@googlegroups.com> wrote: > Hello Tim > This is what I found. > I hope it helps? > > C.A.G. > > > > Thin Stock Support > (part no. LTHINSTK) > > > [image: Thin Stock Support] > > *$99.00* [image: Add To Cart] > <https://web.archive.org/web/20120505180504/http://legacywoodworking.com/cart.cfm?add=15> > > > > > > *Projectsfeaturing theVertical Vise*: > >- Table > > <https://web.archive.org/web/20061017023815/http://www.legacywoodworking.com/galleryItem.cfm?project=90> > > Home > <https://web.archive.org/web/20061017023815/http://www.legacywoodworking.com/index.cfm> > > Products > <https://web.archive.org/web/20061017023815/http://www.legacywoodworking.com/productList.cfm> > > Mill Accessories > <https://web.archive.org/web/20061017023815/http://www.legacywoodworking.com/productList.cfm?type=2> > > > Vertical Vise > Cart : 1 items - $89.00 View > <https://web.archive.org/web/20061017023815/http://www.legacywoodworking.com/cart.cfm> > > Vertical Vise > (part no. LVISEVERT10) > > > [image: Vertical Vise] > > *$119.00* [image: Add To Cart] > <https://web.archive.org/web/20061017023815/http://www.legacywoodworking.com/cart.cfm?add=17> > > > [image: Thin Stock Follower] > Thin Stock Follower > <https://web.archive.org/web/20101009040546/http://legacywoodworking.com/products.cfm?product=99> > ???$$$??? There is not price on this, It only shows up on three catolog > listings and none have a price on them. > > > > > > > > > > > On Monday, March 18, 2019, 7:23:43 AM EDT, Tim Ziegler < > timjzieg...@gmail.com> wrote: > > > Good morning All, > > Does anyone have a price list of the parts that were available for the > LOM's besides what is listed in the back of the manual. > > I have a lead on some parts I have been looking to purchase for my 1200 > LOM and need to know what they cost originally to may a fair offer. > > 1. Thin stock follower > > 2. Thin Stock Support > > 3. Vertical Bench Vise > > > Kind regards, > > > Tim of ZWW > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To post to this group, send email to > legacy-ornamental-mills@googlegroups.com. > Visit this group at > https://groups.google.com/group/legacy-ornamental-mills. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Prices on thin stock follower,thin stock support and vertical Bench vise
Hello TimThis is what I found.I hope it helps? C.A.G. Thin Stock Support (part no. LTHINSTK) $99.00 | Projects featuring the Vertical Vise: - Table | Home > Products > Mill Accessories > Vertical ViseCart : 1 items - $89.00 View | Vertical Vise (part no. LVISEVERT10) $119.00 Thin Stock Follower ???$$$??? There is not price on this, It only shows up on three catolog listings and none have a price on them. | | On Monday, March 18, 2019, 7:23:43 AM EDT, Tim Ziegler wrote: Good morning All, Does anyone have a price list of the parts that were available for the LOM's besides what is listed in the back of the manual. I have a lead on some parts I have been looking to purchase for my 1200 LOM and need to know what they cost originally to may a fair offer. 1. Thin stock follower 2. Thin Stock Support 3. Vertical Bench Vise Kind regards, Tim of ZWW -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Prices on thin stock follower,thin stock support and vertical Bench vise
Good morning All, Does anyone have a price list of the parts that were available for the LOM's besides what is listed in the back of the manual. I have a lead on some parts I have been looking to purchase for my 1200 LOM and need to know what they cost originally to may a fair offer. 1. Thin stock follower 2. Thin Stock Support 3. Vertical Bench Vise Kind regards, Tim of ZWW -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Thin-stock follower & Thin Stock Support HOT
Good morning fellow LOM & WC people. Now that I found the Rotary table I was looking for I am looking for the Thin-Stock follower and Thin Stock Support. I know selling parts from units is not always easy but I bought my LOM 1200 to further my business opportunities and need to move forward. Does anyone have these items for sale or has anyone made after market parts for them? I did see an idea on the "Turn Around" site. But I want the real thing. this is not a part I can get through Legacy. I've tried. Thanks everyone. Kind regards, Tim of ZWW Tim J. Ziegler -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
Re: Thin Stock Support
Curt: I saw a bit I thank on U tube regarding this problem. I will try to find it again. anyway the gentlemen made a holder like the one Tim is writing about. Differance being the holder is mounted to the front of the router table. About 2 or 3 from the bit. It moves with the table so no vibration will get to the bit before it is cut. Nice thing about this is it is always out of the way as you mill a long project. Gene On Wednesday, October 17, 2012 11:28:48 PM UTC-4, Tim wrote: I saw this tonight over on Legacy's cnc forum from Dan1931. He said it was ok to share this idea with others. -- http://legacycncforum.com/report.php?f=17p=4345 Here is a center rest I designed and use canes and other thin work. The cane in the picture is 1.5 in dia. by 32 long. Done with a barley twist with along spiral. I used a 1 barley bit set for a 4 bit twist so it would not have a lot of spring. I then cut thru wiht a .375 Dia end mill. I made the carrier from 1/2 Baltic Birch with reinforced corners. I cut the adjustment slots on my Artisan mill. The white plastic is HDPE. It is available from Tap Plastics. Cost only $5.00. The plastic parts are 7 long so there would not be any vibration or bumping. It is always in contact with the part. I cut small V in the Plastic to hold the part and have 1.25 in spacing between the blocks. This allowed me to cut with the 1 barley twist bit while still supporting the Cane. I provides both lateral and vertical support. Please excuse the quality of the picture. I had to reduce the pixels to get the system to accept it. This looks like an affordable flexible solution. What do you guys think? -Tim -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. Visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. For more options, visit https://groups.google.com/groups/opt_out.
Re: Thin Stock Support
Thanks Gene It sounds pretty good, If you can find it, please copy and post the video to the group? I too will look for it as well. I have some ideas that I will be also tiring ,( Lets see if I can make a better mouse trap?) (so to speak.) ;-) . What I was attempting to do was make a ribbon twist turning.I've done this type of turning before but not on the length ( 5' ) and it was a years ago since I last tried this type of cutting. To cut the ribbon twist you cut from the side of the spindle with a long cutter/router bit, I went form 2 1/4 to something close to 3/4 on a taper before I stopped.although I was taking light cuts, the vibration was to much. I know this was an extreme turning but ... it was just for fun. (in this case No Fun. since it did not turn out.) ;-( Any ideas on making a better steady rest Please let me know? I will let you all know how everything works out latter. Have a good night all. C.A.G. - Original Message - From: Gene To: legacy-ornamental-mills@googlegroups.com Cc: Legacy-Ornamental-Mills@googlegroups.com Sent: Sunday, December 02, 2012 8:17 PM Subject: Re: Thin Stock Support Curt: I saw a bit I thank on U tube regarding this problem. I will try to find it again. anyway the gentlemen made a holder like the one Tim is writing about. Differance being the holder is mounted to the front of the router table. About 2 or 3 from the bit. It moves with the table so no vibration will get to the bit before it is cut. Nice thing about this is it is always out of the way as you mill a long project. Gene On Wednesday, October 17, 2012 11:28:48 PM UTC-4, Tim wrote: I saw this tonight over on Legacy's cnc forum from Dan1931. He said it was ok to share this idea with others. -- Here is a center rest I designed and use canes and other thin work. The cane in the picture is 1.5 in dia. by 32 long. Done with a barley twist with along spiral. I used a 1 barley bit set for a 4 bit twist so it would not have a lot of spring. I then cut thru wiht a .375 Dia end mill. I made the carrier from 1/2 Baltic Birch with reinforced corners. I cut the adjustment slots on my Artisan mill. The white plastic is HDPE. It is available from Tap Plastics. Cost only $5.00. The plastic parts are 7 long so there would not be any vibration or bumping. It is always in contact with the part. I cut small V in the Plastic to hold the part and have 1.25 in spacing between the blocks. This allowed me to cut with the 1 barley twist bit while still supporting the Cane. I provides both lateral and vertical support. Please excuse the quality of the picture. I had to reduce the pixels to get the system to accept it. This looks like an affordable flexible solution. What do you guys think? -Tim -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. Visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. For more options, visit https://groups.google.com/groups/opt_out. -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. Visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. For more options, visit https://groups.google.com/groups/opt_out.
Re: Thin Stock Support
I will try to post some pictures if I can get my computer to work. On Dec 2, 2012 9:29 PM, curt george curtgeo...@wowway.com wrote: Thanks Gene It sounds pretty good, If you can find it, please copy and post the video to the group? I too will look for it as well. I have some ideas that I will be also tiring ,( Lets see if I can make a better mouse trap?) (so to speak.) ;-) . What I was attempting to do was make a ribbon twist turning.I've done this type of turning before but not on the length ( 5' ) and it was a years ago since I last tried this type of cutting. To cut the ribbon twist you cut from the side of the spindle with a long cutter/router bit, I went form 2 1/4 to something close to 3/4 on a taper before I stopped.although I was taking light cuts, the vibration was to much. I know this was an extreme turning but ... it was just for fun. (in this case No Fun. since it did not turn out.) ;-( Any ideas on making a better steady rest Please let me know? I will let you all know how everything works out latter. Have a good night all. C.A.G. - Original Message - From: Gene To: legacy-ornamental-mills@googlegroups.com Cc: Legacy-Ornamental-Mills@googlegroups.com Sent: Sunday, December 02, 2012 8:17 PM Subject: Re: Thin Stock Support Curt: I saw a bit I thank on U tube regarding this problem. I will try to find it again. anyway the gentlemen made a holder like the one Tim is writing about. Differance being the holder is mounted to the front of the router table. About 2 or 3 from the bit. It moves with the table so no vibration will get to the bit before it is cut. Nice thing about this is it is always out of the way as you mill a long project. Gene On Wednesday, October 17, 2012 11:28:48 PM UTC-4, Tim wrote: I saw this tonight over on Legacy's cnc forum from Dan1931. He said it was ok to share this idea with others. -- Here is a center rest I designed and use canes and other thin work. The cane in the picture is 1.5 in dia. by 32 long. Done with a barley twist with along spiral. I used a 1 barley bit set for a 4 bit twist so it would not have a lot of spring. I then cut thru wiht a .375 Dia end mill. I made the carrier from 1/2 Baltic Birch with reinforced corners. I cut the adjustment slots on my Artisan mill. The white plastic is HDPE. It is available from Tap Plastics. Cost only $5.00. The plastic parts are 7 long so there would not be any vibration or bumping. It is always in contact with the part. I cut small V in the Plastic to hold the part and have 1.25 in spacing between the blocks. This allowed me to cut with the 1 barley twist bit while still supporting the Cane. I provides both lateral and vertical support. Please excuse the quality of the picture. I had to reduce the pixels to get the system to accept it. This looks like an affordable flexible solution. What do you guys think? -Tim -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. Visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. For more options, visit https://groups.google.com/groups/opt_out. -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. Visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. For more options, visit https://groups.google.com/groups/opt_out. -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. Visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. For more options, visit https://groups.google.com/groups/opt_out.
Re: Thin Stock Support
Good morning everyone, ;-) this is an old topic, But nicely done, this stock support can be made easily by anyone who owns a Legacy, My hat is off to Dan1931. he did a good job. This is a good reminder to everyone,that we all can use our machines better,and we do not need to spend an arm and a leg to buy things that we need. We can make much of what is needed. Very Nice! Thank you Tim, for posting this one. it is a good find. and a Great Reminder. Look what you can do! Its a good way to start the day! ;-) . C.A.G. - Original Message - From: Tim Krause To: Legacy-Ornamental-Mills@googlegroups.com Sent: Wednesday, October 17, 2012 11:30 PM Subject: Thin Stock Support I saw this tonight over on Legacy's cnc forum from Dan1931. He said it was ok to share this idea with others. -- Here is a center rest I designed and use canes and other thin work. The cane in the picture is 1.5 in dia. by 32 long. Done with a barley twist with along spiral. I used a 1 barley bit set for a 4 bit twist so it would not have a lot of spring. I then cut thru wiht a .375 Dia end mill. I made the carrier from 1/2 Baltic Birch with reinforced corners. I cut the adjustment slots on my Artisan mill. The white plastic is HDPE. It is available from Tap Plastics. Cost only $5.00. The plastic parts are 7 long so there would not be any vibration or bumping. It is always in contact with the part. I cut small V in the Plastic to hold the part and have 1.25 in spacing between the blocks. This allowed me to cut with the 1 barley twist bit while still supporting the Cane. I provides both lateral and vertical support. Please excuse the quality of the picture. I had to reduce the pixels to get the system to accept it. This looks like an affordable flexible solution. What do you guys think? -Tim -- -- center rest mail3.jpg
Re: Thin Stock Support
looks good to me can you post a bigger clearer pic or is that the bes one there is Bill B - Original Message - From: Tim Krause To: Legacy-Ornamental-Mills@googlegroups.com Sent: Thursday, October 18, 2012 2:30 PM Subject: Thin Stock Support I saw this tonight over on Legacy's cnc forum from Dan1931. He said it was ok to share this idea with others. -- Here is a center rest I designed and use canes and other thin work. The cane in the picture is 1.5 in dia. by 32 long. Done with a barley twist with along spiral. I used a 1 barley bit set for a 4 bit twist so it would not have a lot of spring. I then cut thru wiht a .375 Dia end mill. I made the carrier from 1/2 Baltic Birch with reinforced corners. I cut the adjustment slots on my Artisan mill. The white plastic is HDPE. It is available from Tap Plastics. Cost only $5.00. The plastic parts are 7 long so there would not be any vibration or bumping. It is always in contact with the part. I cut small V in the Plastic to hold the part and have 1.25 in spacing between the blocks. This allowed me to cut with the 1 barley twist bit while still supporting the Cane. I provides both lateral and vertical support. Please excuse the quality of the picture. I had to reduce the pixels to get the system to accept it. This looks like an affordable flexible solution. What do you guys think? -Tim -- -- center rest mail3.jpg
Re: Thin Stock Support
That plastic is really common. Cutting boards are made out of the same material. You are correct on your assumption. -Tim --
Re: Thin Stock Support
Thank You On 2012-10-18, at 8:22 PM, Tim Krause artmarb...@comcast.net wrote: That plastic is really common. Cutting boards are made out of the same material. You are correct on your assumption. -Tim -- --
Re: thin stock support
Very Nice Bill Where did you get those brackets? They look factory made. If you made those by hand, I take my hat off to you. (WoW! Nice job.) When not in use as a stock support, you can also us them and the new Legacy mobility kit. (Need to move your Legacy? No problem, not with the Big Bill's mobility kit!) ;-) Awesome job Bill. thanks for sharing. C.A.G. - Original Message - From: Bill Bulkeley bulke...@mmnet.com.au To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 2:40 AM Subject: Re: thin stock support I just made this I havent even tryed it out it looks as if it will hold work 7/8 inch to a bit over 3 inches I will give it a try when i do another karate stick my new piece of purple heart arrived today. Bill - Original Message - From: aussiman bulke...@mmnet.com.au To: Legacy Ornamental Mills legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 4:36 PM Subject: thin stock support some rail a few legacy bolts and brackets 2 scooter wheels from the local toy shop and a simple thin stock support is born. I found these wheels in out local toy shop and i knew i could put them to some good woodwork use. some pics to follow Bill -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. - No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1388 / Virus Database: 1516/3734 - Release Date: 06/29/11 -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en.
Re: thin stock support
all the brackets are legacy's all I bought and added was the wheels and 2 bolts Bill - Original Message - From: curt george curtgeo...@wowway.com To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 10:13 PM Subject: Re: thin stock support Very Nice Bill Where did you get those brackets? They look factory made. If you made those by hand, I take my hat off to you. (WoW! Nice job.) When not in use as a stock support, you can also us them and the new Legacy mobility kit. (Need to move your Legacy? No problem, not with the Big Bill's mobility kit!) ;-) Awesome job Bill. thanks for sharing. C.A.G. - Original Message - From: Bill Bulkeley bulke...@mmnet.com.au To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 2:40 AM Subject: Re: thin stock support I just made this I havent even tryed it out it looks as if it will hold work 7/8 inch to a bit over 3 inches I will give it a try when i do another karate stick my new piece of purple heart arrived today. Bill - Original Message - From: aussiman bulke...@mmnet.com.au To: Legacy Ornamental Mills legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 4:36 PM Subject: thin stock support some rail a few legacy bolts and brackets 2 scooter wheels from the local toy shop and a simple thin stock support is born. I found these wheels in out local toy shop and i knew i could put them to some good woodwork use. some pics to follow Bill -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. - No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1388 / Virus Database: 1516/3734 - Release Date: 06/29/11 -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. - No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1388 / Virus Database: 1516/3734 - Release Date: 06/29/11 -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en.
RE: thin stock support
Did you buy them or did they come with you machine? I don't have any that look like that and defiantly no extras that look like it. Thanks Greg -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en.
Re: thin stock support
Hello Bill in my manual it states that I can up-grade my machine with longer rail but there are not pictures or anything other than the statement. It looks like you got everything that you've got, right off the shelf, so to speak. Even if the parts are still available its hard to order parts with out seeing if they are the same as what you have. (In short no order no. No part number.No names,or ??? Makes it very hard to get what you want.) I will do some home work and see if I can come up with something. ;-) Thanks for sharing with us. C.A.G. - Original Message - From: Bill Bulkeley bulke...@mmnet.com.au To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 12:40 PM Subject: Re: thin stock support the 90 degree brackets I ordered from legacy they were used on a older model machine the 200 I believe it was. and the strait brackets are from the template rail mounting kit an extra legacy used to sell, I don't know if they would still have any I bought several of them once, it was the cheapest way of getting some extra rail at the time to lengthen my model 900. each one came with the brackets so I ended up with several of them, there should be pictures of the kit in your legacy manual that came with the machine.I'm sure you guys over there would have a lot easier job getting these parts now if available than I would way over here in Australia Bill - Original Message - From: Groovy Wood LLC groovyw...@gmail.com To: legacy-ornamental-mills@googlegroups.com Sent: Friday, July 01, 2011 2:20 AM Subject: RE: thin stock support Did you buy them or did they come with you machine? I don't have any that look like that and defiantly no extras that look like it. Thanks Greg -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. - No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1388 / Virus Database: 1516/3734 - Release Date: 06/29/11 -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en.
Re: thin stock support
knowing legacy as i do good luck Bill - Original Message - From: curt george curtgeo...@wowway.com To: legacy-ornamental-mills@googlegroups.com Sent: Friday, July 01, 2011 4:16 AM Subject: Re: thin stock support Hello Bill in my manual it states that I can up-grade my machine with longer rail but there are not pictures or anything other than the statement. It looks like you got everything that you've got, right off the shelf, so to speak. Even if the parts are still available its hard to order parts with out seeing if they are the same as what you have. (In short no order no. No part number.No names,or ??? Makes it very hard to get what you want.) I will do some home work and see if I can come up with something. ;-) Thanks for sharing with us. C.A.G. - Original Message - From: Bill Bulkeley bulke...@mmnet.com.au To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 12:40 PM Subject: Re: thin stock support the 90 degree brackets I ordered from legacy they were used on a older model machine the 200 I believe it was. and the strait brackets are from the template rail mounting kit an extra legacy used to sell, I don't know if they would still have any I bought several of them once, it was the cheapest way of getting some extra rail at the time to lengthen my model 900. each one came with the brackets so I ended up with several of them, there should be pictures of the kit in your legacy manual that came with the machine.I'm sure you guys over there would have a lot easier job getting these parts now if available than I would way over here in Australia Bill - Original Message - From: Groovy Wood LLC groovyw...@gmail.com To: legacy-ornamental-mills@googlegroups.com Sent: Friday, July 01, 2011 2:20 AM Subject: RE: thin stock support Did you buy them or did they come with you machine? I don't have any that look like that and defiantly no extras that look like it. Thanks Greg -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. - No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1388 / Virus Database: 1516/3734 - Release Date: 06/29/11 -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. - No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1388 / Virus Database: 1516/3734 - Release Date: 06/29/11 -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en.
Re: thin stock support
if legacy doesn't make them any more then maybe Tim can or similar. sounds like a few out there might like some what do you think Bill - Original Message - From: curt george curtgeo...@wowway.com To: legacy-ornamental-mills@googlegroups.com Sent: Friday, July 01, 2011 11:28 AM Subject: Re: thin stock support Thanks Tim Those brackets are the real trick to making this stock support work.(Not trying to take anything away from you Bill, Great job on this one.) But Having those two little tangs hold the brackets in place with only one mounting screw to mount it on the Legacy rails are A Real SLICK Idea! I have no idea who came up with that! But who ever did is one pretty smart Cookie in my books. Legacy did not have anything like that when I bought my unit. Those brackets alone would have taken up much of the slop with in the rails, that the earlier Legacy's had. Man Just think about it, with those brackets alone, we might have been able to keep many of our Fast Eddies Happy Legacy customer back then. OWell that's water under the bridge now! Just my two cents worth of it. I like it! Its ESP (Efficient,Simple, and Practical.) You cant ask for anything more. That alone makes it an A+ in my book. ;-) C.A.G. - Original Message - From: Tim Krause artmarb...@comcast.net To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 7:39 PM Subject: Re: thin stock support The tall bracket that holds the wheels are from the template upgrade kit like Bill said. The other angle bracket with two tabs are used to hold the vertical and horizontal vises in place. The wheels look like roller blade wheels that can be bought at sporting goods stores, or you can get them off a used pair of skates at most thrift stores. The bearings are typically 8mm which mount very easily to some 5/16 all- thread or bolt. It should take very little time to make a bracket to hold the wheels. I would think you could get away with only one bracket to hold the wheels. -Tim - Original Message - From: curt george curtgeo...@wowway.com To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 11:16 AM Subject: Re: thin stock support Hello Bill in my manual it states that I can up-grade my machine with longer rail but there are not pictures or anything other than the statement. It looks like you got everything that you've got, right off the shelf, so to speak. Even if the parts are still available its hard to order parts with out seeing if they are the same as what you have. (In short no order no. No part number.No names,or ??? Makes it very hard to get what you want.) I will do some home work and see if I can come up with something. ;-) Thanks for sharing with us. C.A.G. - Original Message - From: Bill Bulkeley bulke...@mmnet.com.au To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 12:40 PM Subject: Re: thin stock support the 90 degree brackets I ordered from legacy they were used on a older model machine the 200 I believe it was. and the strait brackets are from the template rail mounting kit an extra legacy used to sell, I don't know if they would still have any I bought several of them once, it was the cheapest way of getting some extra rail at the time to lengthen my model 900. each one came with the brackets so I ended up with several of them, there should be pictures of the kit in your legacy manual that came with the machine.I'm sure you guys over there would have a lot easier job getting these parts now if available than I would way over here in Australia Bill - Original Message - From: Groovy Wood LLC groovyw...@gmail.com To: legacy-ornamental-mills@googlegroups.com Sent: Friday, July 01, 2011 2:20 AM Subject: RE: thin stock support Did you buy them or did they come with you machine? I don't have any that look like that and defiantly no extras that look like it. Thanks Greg -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. - No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1388 / Virus Database: 1516/3734 - Release Date: 06/29/11 -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. -- You received this message
Re: thin stock support
You know, I can make any bracket that comes to mind. Anyone can contact me off list and lets see if we can make a deal. I offer drafting services, fabrication and ideas to get your project moving in the right direction. Your only limitation is communication :-) -Tim - Original Message - From: Bill Bulkeley bulke...@mmnet.com.au To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 7:30 PM Subject: Re: thin stock support if legacy doesn't make them any more then maybe Tim can or similar. sounds like a few out there might like some what do you think Bill - Original Message - From: curt george curtgeo...@wowway.com To: legacy-ornamental-mills@googlegroups.com Sent: Friday, July 01, 2011 11:28 AM Subject: Re: thin stock support Thanks Tim Those brackets are the real trick to making this stock support work.(Not trying to take anything away from you Bill, Great job on this one.) But Having those two little tangs hold the brackets in place with only one mounting screw to mount it on the Legacy rails are A Real SLICK Idea! I have no idea who came up with that! But who ever did is one pretty smart Cookie in my books. Legacy did not have anything like that when I bought my unit. Those brackets alone would have taken up much of the slop with in the rails, that the earlier Legacy's had. Man Just think about it, with those brackets alone, we might have been able to keep many of our Fast Eddies Happy Legacy customer back then. OWell that's water under the bridge now! Just my two cents worth of it. I like it! Its ESP (Efficient,Simple, and Practical.) You cant ask for anything more. That alone makes it an A+ in my book. ;-) C.A.G. - Original Message - From: Tim Krause artmarb...@comcast.net To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 7:39 PM Subject: Re: thin stock support The tall bracket that holds the wheels are from the template upgrade kit like Bill said. The other angle bracket with two tabs are used to hold the vertical and horizontal vises in place. The wheels look like roller blade wheels that can be bought at sporting goods stores, or you can get them off a used pair of skates at most thrift stores. The bearings are typically 8mm which mount very easily to some 5/16 all- thread or bolt. It should take very little time to make a bracket to hold the wheels. I would think you could get away with only one bracket to hold the wheels. -Tim - Original Message - From: curt george curtgeo...@wowway.com To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 11:16 AM Subject: Re: thin stock support Hello Bill in my manual it states that I can up-grade my machine with longer rail but there are not pictures or anything other than the statement. It looks like you got everything that you've got, right off the shelf, so to speak. Even if the parts are still available its hard to order parts with out seeing if they are the same as what you have. (In short no order no. No part number.No names,or ??? Makes it very hard to get what you want.) I will do some home work and see if I can come up with something. ;-) Thanks for sharing with us. C.A.G. - Original Message - From: Bill Bulkeley bulke...@mmnet.com.au To: legacy-ornamental-mills@googlegroups.com Sent: Thursday, June 30, 2011 12:40 PM Subject: Re: thin stock support the 90 degree brackets I ordered from legacy they were used on a older model machine the 200 I believe it was. and the strait brackets are from the template rail mounting kit an extra legacy used to sell, I don't know if they would still have any I bought several of them once, it was the cheapest way of getting some extra rail at the time to lengthen my model 900. each one came with the brackets so I ended up with several of them, there should be pictures of the kit in your legacy manual that came with the machine.I'm sure you guys over there would have a lot easier job getting these parts now if available than I would way over here in Australia Bill - Original Message - From: Groovy Wood LLC groovyw...@gmail.com To: legacy-ornamental-mills@googlegroups.com Sent: Friday, July 01, 2011 2:20 AM Subject: RE: thin stock support Did you buy them or did they come with you machine? I don't have any that look like that and defiantly no extras that look like it. Thanks Greg -- You received this message because you are subscribed to the Google Groups Legacy Ornamental Mills group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http
