Re: [AFMUG] From AnimalFarm - Cambium LTE

That slide was more of an example of the potential of separating the BBU from the RRH and wasn't meant to be a statement of roadmap. :) But that's a good catch, Chuck. As stated in other emails, its 2.5G first and unlicensed coming later. Aaron From: Af [mailto:af-boun...@afmug.com] On Behal

Re: [AFMUG] Firmware

We are tracking one last issue for the release related to multiple simultaneous SM session drops. We will have an open beta refresh build this week which should be 99.9% of the way to release. We are looking to have the official release within 2 weeks, but depends on this last issue. Regards,

Re: [AFMUG] High Priority Uplink / Downlink

There is a significant improvement in the application of MIR and burst coming in 14.2 for 450i. Historically we consumed data at the achievable rate and refilled at a fixed rate (once per second). So this lead to very bursty consumption of burst bucket and MIR and quiet link for remainder of t

Re: [AFMUG] High Priority Uplink / Downlink

That isn't quite true about all Hi Priority traffic going before Low Priority CIR... Leaving Hi Priority MIR at 0/0 is useful if you set a Low Priority CIR, in that case the LP CIR will be honored, then it will move to High Priority traffic. Recall that the priority order proceeds as follow:

Re: [AFMUG] 450 "silent watchdog reset" question

on Assuming the scanning caused it, then it wouldn't be a re-reg since that doesn't trigger a full scan. You could look at the session log for that SM and see if that shows any out-of-service (OOS) and/or reg attempts. Maybe Aaron can tell you exactly what that means. Bad frequency offs

Re: [AFMUG] 450 14.1.2 build 4

Yes, I was facetiously joking that a fix for the issue would be available around March 21st in the Northern Hemisphere without a SW upgrade. :) But, we were able to reproduce it at room temperature a lot during our investigation, so while colder temperatures do make it worse, it is not wholly t

[AFMUG] PMP 450 AP reset update WAS 14.1.1?

Absolutely that is the goal! Here is an update for all of you. It turns out this was not a “simple” timing issue as we originally had thought, which is why the investigation has been dragging on. We finally understand what is happening, have ideas on where/how it started, and are working on f

Re: [AFMUG] Cambium 450 Watchdog resets - was: To Cambium With Love- Replace the bad ePMP units.

spectrum coherency. So I looked it up. I think we used to have a different name for this... like asynchronous bus arbiter? From: Aaron Schneider<mailto:aaron.schnei...@cambiumnetworks.com> Sent: Thursday, January 21, 2016 5:50 PM To: af@afmug.com<mailto:af@afmug.com> Subject: Re: [AF

Re: [AFMUG] Cambium 450 Watchdog resets - was: To Cambium With Love- Replace the bad ePMP units.

ne St Suite 1337 Troy, OH 45373 On Jan 21, 2016 7:50 PM, "Aaron Schneider" mailto:aaron.schnei...@cambiumnetworks.com>> wrote: Hi Everyone – Sorry for the delay in response on this thread. I’d like to give an update of where we are with this issue. First off, I would like to apol

Re: [AFMUG] Cambium 450 Watchdog resets - was: To Cambium With Love- Replace the bad ePMP units.

Hi Everyone - Sorry for the delay in response on this thread. I'd like to give an update of where we are with this issue. First off, I would like to apologize for the issues that this is causing. We have heard reports for awhile in varying fashion, and Tushar had been talking about having t

Re: [AFMUG] Canopy 14.1.1

m: Af [mailto:af-boun...@afmug.com] On Behalf Of Aaron Schneider Sent: Tuesday, December 01, 2015 5:19 PM To: Darren Shea; af@afmug.com Subject: Re: [AFMUG] Canopy 14.1.1 Darren - We'll take a look but the external gain for 450D is locked because that is the property of the HW with the attached dish

Re: [AFMUG] Canopy 14.1.1

that some customers were having issues installing these in 5.4G band, but the tx power should be correct. Regards, -Aaron -Original Message- From: Darren Shea [mailto:darr...@ecpi.com] Sent: Tuesday, December 01, 2015 3:58 PM To: af@afmug.com Cc: Matt Mangriotis; Aaron Schneider Subject:

Re: [AFMUG] Canopy 14.1.1 Release and PTP

mailto:af-boun...@afmug.com>> on behalf of >> Mark Radabaugh mailto:m...@amplex.net>> >> Sent: Saturday, November 28, 2015 8:24 AM >> To: af@afmug.com<mailto:af@afmug.com> >> Subject: Re: [AFMUG] Canopy 14.1.1 Release and PTP >> >> How abou

Re: [AFMUG] Canopy 14.1.1 Release and PTP

It should work, but at the moment I can’t recall if/when we tried this with PTP mode. I’ll let you know. 450i - 450 isn’t really an “interop” situation like 430 - 450 was. 430 - 450 was quite a bit different, needing SISO to talk to MIMO with the way we did MIMO at first (MIMO-B using both

Re: [AFMUG] 450 AP on iGPS makes opposite AP invisible?

ou DO have an email filter that looks for your name :) >> >> And this sounds awesome. >> >> On 11/24/2015 10:00 PM, Aaron Schneider wrote: >>> Coming in 14.1.1 for 450/450i and 13.4.1 for 100/430 series, you’ll see >>> fixes for lining up the various s

Re: [AFMUG] Canopy 14.1.1

I can help if that is necessary. I’ll forward this on internally. On 11/25/15, 6:02 PM, "Af on behalf of George Skorup" wrote: >I see it made it to the support site today. How about putting up >13.2.1.3 for us with Lite APs that may want to go back?

Re: [AFMUG] PMP450i 900MHz

Yes, and the aforementioned sync pulse alignment updates may require you to run the 900 450i in a legacy mode until you can upgrade your FSK 900 sectors to the new load that makes them line up as well. This information is in the user guide and release notes. From: Af mailto:af-boun...@afmug.com

Re: [AFMUG] Cambium 450i

incorporated into your capacity planner so operators that do have bottlenecks could see what swapping to a 450i could actually improve over the 450? On Tue, Nov 24, 2015 at 10:09 PM, Aaron Schneider mailto:aaron.schnei...@cambiumnetworks.com>> wrote: 14.1.1 should hit the webpage tom

Re: [AFMUG] PMP450i 900MHz

The SM could survive the fish tank test, but not in the same manner as the AP, you’d have to insert it vertically due to the shroud cover, whereas the AP could be laid in there on its side. We might have to give this one a try next week. :) From: Af mailto:af-boun...@afmug.com>> on behalf of St

Re: [AFMUG] Cambium 450i

14.1.1 should hit the webpage tomorrow with formal release. 900M 450i AP / 450 SM should also start shipping very soon, with 14.1.1. Due to the timelines of our releases lining up, we skipped 14.1 for 450i/450 compatibility and went to 14.1.1. Just in time for Thanksgiving! :D Just swapping o

Re: [AFMUG] 450 AP on iGPS makes opposite AP invisible?

wonder if Cambium could give us a toggle between CMM3 and CMM4 for the >on-board GPS? Paging Aaron Schneider > >AFAIK, the stuck issue is/was only the FreeRun mode. AutoSync does not >go back to the timing port or power port if they return while it's >running on the on-boar

Re: [AFMUG] 450 SM corrupt flash?

. So if I upgrade this SM to 14.1.1, will it register to a 13.2.1 AP? And the other way around, how about 13.2.1 SMs on 14.1.1 APs? There's always that handful of customers that power off their radios when they're not using it. On 11/22/2015 1:45 AM, Aaron Schneider wrote: Hi George -

Re: [AFMUG] 450 SM corrupt flash?

Hi George - This is a bug where the event log gets corrupt and kind of locks itself in place. If you load the latest 14.1.1 open beta, it will recover the event log and also has a fix so that any future crash logs won’t be able to lead to this problem. Unfortunately there is no way for you to

Re: [AFMUG] 450 frame utilization and performance issues

The scheduler operates on-demand in the downlink, applying the priority rules covered many times before, and by request in the uplink - SMs need to request to the AP to be scheduled, and the AP schedules uplink based on the same priority rules. An external traffic shaping device operating on t

Re: [AFMUG] LTE Speeds

M To: af@afmug.com Subject: Re: [AFMUG] LTE Speeds I invoke the name of Aaron Schneider and he appears! I am the dungeon master of AFMUG! I see your point. In a nutshell the problem is that we are marketing bits per second, but what we actually have to hand out is air time. We can try to delive

Re: [AFMUG] LTE Speeds

in bps or "capacity" in time slots. I'm thinking it's the latter because I have observed that if you improve the data rate of an individual SM he'll get more, which makes sense if the SM's capacity allotment is measured in timeslots rather than bits. Where's

Re: [AFMUG] 13.4 QOS not working or is it better?

Also, there are different modes of Link Test. The only one that should bring MIR settings into the test is the “Link Test with Bridging and MIR”. If you don’t select that option, then there will be no MIR throttling of the Link Test packets. -Aaron From: Af on behalf of Matt Mangriotis Reply

Re: [AFMUG] OT BYU vs Nebraska

Nebraska is my alma mater. I saw that play in all of its glory live with a room full of Husker fans. You could hear a pin drop! My first thought was that now we know how Northwestern felt when Nebraska did that same thing to them 2 years ago from midfield. Which would you rather have? Won

Re: [AFMUG] Canopy 13.4 Watchdog Reset

not worse. It’s like a medicine ad on TV: Have you asked your doctor if Vunderpill is right for you? It may reduce the severity of flare-ups of heartburn. Possible side effects include jimmy leg, droopy face, thoughts of suicide, head explosions. From: Af [mailto:af-boun...@afmug.com] On Behalf

Re: [AFMUG] Canopy 13.4 Watchdog Reset

Hi Everyone – Sorry I’ve been in hibernation for the past several months! If you’d like to try the test load regarding the watchdog issue, please reply to me offline (aa...@cambiumnetworks.com). We’re working to gather information about sites that seem more

Re: [AFMUG] RM5AC-PMP Embargo lifted..

So do we. :D From: Af [mailto:af-boun...@afmug.com] On Behalf Of Ben Moore via Af Sent: Thursday, December 11, 2014 10:48 AM To: af@afmug.com Subject: Re: [AFMUG] RM5AC-PMP Embargo lifted.. We have a whole wall for you... ;) On Thu, Dec 11, 2014 at 9:46 AM, Josh Luthman via Af mailto:af@afmug.

Re: [AFMUG] 13.3 Open Beta

1100 Wayne St Suite 1337 Troy, OH 45373 On Dec 3, 2014 12:41 PM, "Aaron Schneider via Af" mailto:af@afmug.com>> wrote: It is definitely being considered and your voices are being heard. I just can’t comment on it just yet. :) From: Af [mailto:af-boun...@afmug.com<mailto:af-bou

Re: [AFMUG] 13.3 Open Beta

It is definitely being considered and your voices are being heard. I just can’t comment on it just yet. :) From: Af [mailto:af-boun...@afmug.com] On Behalf Of George Skorup (Cyber Broadcasting) via Af Sent: Wednesday, December 03, 2014 11:39 AM To: af@afmug.com Subject: Re: [AFMUG] 13.3 Open Be

Re: [AFMUG] 13.3 Open Beta

They are all told to run it simultaneously and while the SMs are doing it, the AP shuts itself up and runs a scan during that time. From: Af [mailto:af-boun...@afmug.com] On Behalf Of Gino Villarini via Af Sent: Wednesday, December 03, 2014 11:37 AM To: af@afmug.com Subject: Re: [AFMUG] 13.3 Op

Re: [AFMUG] 13.3 Open Beta

13.3 is for PMP450 and PTP450 only. ;) That being said, we are close to having a 13.2.1 ready that fixes the issues reported with 13.2 including the PTP230 reboot issue. We have found that the problem is VLAN related and only affects PTP230. Regards, -Aaron -Original Message- From: A

Re: [AFMUG] 13.3 Open Beta

Eric – We are looking at our options for bringing another release to FSK but I can’t comment on that just yet. -Aaron From: Af [mailto:af-boun...@afmug.com] On Behalf Of Eric Muehleisen via Af Sent: Wednesday, December 03, 2014 11:25 AM To: af@afmug.com Subject: Re: [AFMUG] 13.3 Open Beta *

Re: [AFMUG] 13.3 Open Beta

When running Sector Spectrum Analyzer (SA), once the sector is done, you'll be able to go through the scan results for the AP as well as all of the SMs (via the Remote SA page). For the PTP Map removal, Jonathan is correct in the throughput improvement. But be aware that you MUST upgrade the "

Re: [AFMUG] v13.2 - ptp230

Mathieu - have you sent these into anyone yet? if not, please send to me off list. Thanks, -Aaron aa...@cambiumnetworks.com -Original Message- From: Af [mailto:af-boun...@afmug.com] On Behalf Of Mathieu via Af Sent: Wednesday, November 19, 2014 9:53 AM To: af@afmug.com Subject: Re: [AF

Re: [AFMUG] System Release 13.2 is Official

Hi Matt This is what most customers use the primary/secondary/tertiary color codes for. That in conjunction with the rescan timers will automatically make the sms rescan to try to get back on a primary color code if they had to use a backup to register. Regards, Aaron Sent from my Verizon

Re: [AFMUG] System Release 13.2 is Official

13.2 final on SM with beta on AP the SM will reboot it self when you do a cap test this is the same bug I reported on build 35 — Sent from Mailbox<https://www.dropbox.com/mailbox> On Fri, Nov 14, 2014 at 4:46 PM, Aaron Schneider via Af mailto:af@afmug.com>> wrote: There was a decisi

Re: [AFMUG] Issue with SNMP OID .1.3.6.1.4.1.161.19.3.2.1.1.0

Hi John – The complete list of OIDs affected by this problem are: 1.3.6.1.4.1.161.19.3.2.1.1 rfScanListDisplayString 1.3.6.1.4.1.161.19.3.2.1.79 pppoeAccessConcentrator DisplayString 1.3.6.1.4.1.161.19.3.2.1.80 pppoeServiceName DisplayString 1.3.6.1.4.1.

Re: [AFMUG] System Release 13.2 is Official

There was a decision made when we added 2.5 center channels that on upgrade we wouldn’t automatically check the 2.5 centers unless the scan list was in a default (all checked) state. We didn’t want to add a ton of new scan options on an upgrade which increased the scanning time. When setting

Re: [AFMUG] System Release 13.2 is Official

Hi Eric – Yes, there were great improvements to the hysteresis of the rate adapt and improving the backoff algorithms. You will no longer see a penalty when not being able to get to the next higher tier rate as you did with previous releases. Also, MIMO-A is just another Rate Adapt level tha

Re: [AFMUG] 13.2 Issue (Removing frequency checkboxes)

.3 to 13.2. Has anyone else upgraded a 2.4 GHz sector and run into this issue (or did not run into this issue)? Rajesh Vijayakumar Cambium Networks On Thu, Nov 13, 2014 at 10:45 PM, Aaron Schneider via Af mailto:af@afmug.com>> wrote: We are investigating the other issues, but with respect

Re: [AFMUG] 13.2 Issue (Removing frequency checkboxes)

We are investigating the other issues, but with respect to 5767.5 and 5807.5, those two were affected by a bug fix, in that pre-13.2, 5767.5 was actually enabling 5767.20, due to an obvious typo in the scan list code, and 5807.5 was actually enabling 5807.00, due to another typo bug in the code.

Re: [AFMUG] System Release 13.2 is Official

Thank you very much for all of you that helped with Open Beta. It was a very long release, but there were lots of things found and fixed as a result of having you helping us with access to your systems. I’d like to highlight here, for those of you that don’t read the release notes, due to the

Re: [AFMUG] 13.2(Build 35) Open Beta

Sean – I do see a reply there from Jonathan that was posted yesterday afternoon. Hit me offlist if you can, he is requesting some more information. Thanks, -Aaron From: Af [mailto:af-boun...@afmug.com] On Behalf Of Aaron Schneider via Af Sent: Thursday, October 30, 2014 6:56 PM To: af@afmug.com

Re: [AFMUG] 13.2(Build 35) Open Beta

that dose a continuas link capacity test at the same time showing you real time signal so we can properly install antenna's? Thanks, — Sent from Mailbox<https://www.dropbox.com/mailbox> On Thu, Oct 30, 2014 at 5:54 PM, Aaron Schneider via Af mailto:af@afmug.com>> wrote: Buil

Re: [AFMUG] 13.2(Build 35) Open Beta

...@afmug.com] On Behalf Of Sean Heskett via Af Sent: Thursday, October 30, 2014 5:15 PM To: af@afmug.com Subject: Re: [AFMUG] 13.2(Build 35) Open Beta Aaron, I submitted a sessions status page bug on the beta forum but never saw any reply??? On Thursday, October 30, 2014, Aaron Schneider via Af

Re: [AFMUG] 13.2(Build 35) Open Beta

Build 35 took care of the AP Ethernet hangup, which was the main one being worked during Wispapalooza. There will be a Build 36 put on Open Beta probably tomorrow in which we were able to fix for some of the old nagging rare and random crashes that have been seen in previous releases. Our curr

Re: [AFMUG] 13.2(Build 35) Open Beta

If you aren't seeing it on build 34, you are unlikely to need the fix, but you are still at risk. The customer who was seeing it readily would see it mostly occur during the CNUT upgrade phase when using AP as the file server. Once the upgrade was done, the event log recovery message very rare

Re: [AFMUG] 13.2(Build 35) Open Beta

All – Changes in this build include an updated fix for the remaining 13.2 release blocker. As I discussed with many of you at Wispapalooza, that issue was related to the “Ethernet Tx Ring stall” message that may show up in the event log, where very rarely, the recovery didn’t recover. Because

Re: [AFMUG] ptp 450

Hi Ryan - This version was only used for shipping devices and we don't plan on making it available. It is actually based on a branch from 13.2 (Build 27) on a PTP branch so that we could get the product shipping. Please contact me offlist (aa...@cambiumnetworks.com

Re: [AFMUG] 13.2 (Build32) Beta Software is Now Available!‏‏

Since the last Open Beta load (Build 30), this also contains: * Fix for negative VC count on home page * New OID to see NAT table size in use * Fix for Active FTP with NAT * PPPoE Control Message High Priority with VLAN Enabled ·Added missing OIDs for IPv6 packet filterin

Re: [AFMUG] PMP450 AP stopped responding

. Program will exit. Exception in thread "main" Tool Complete with exit status:1 End Time: September 26, 2014 2:04:35 PM He also said I would be getting an email with information about submitting the dump and I haven't got that either. On Fri, Sep 26, 2014 at 1:44 PM, Aaron Schneider vi

Re: [AFMUG] PMP450 AP stopped responding

stopped responding Seeing -237 and such VC counts on the first page of 5.4 450 APs. Other types seem to count correctly. 13.2B30 Allen Sent from my Ranch Phone On Sep 26, 2014, at 3:44 PM, Aaron Schneider via Af mailto:af@afmug.com>> wrote: Hi Ryan – While I can’t say for certain what caus

Re: [AFMUG] PMP450 AP stopped responding

Hi Ryan – While I can’t say for certain what caused the Ethernet Core to get stuck, there are two things in 13.2 that will help with this. First off, there was a bug in this reporting mechanism that wasn’t allowing a recovery to take place. That recovery should have been an AP reboot but the

Re: [AFMUG] Dear Cambium

--- [ Aaron Schneider wrote ]: --- Hmm, this is odd - yours and Sean's messages came in as an attachment to an empty message... Anyways, yes, we are well aware that FSK is never going away, we've been the ones keeping it going for this long! We to

Re: [AFMUG] Dear Cambium

ew ESN. So if this is not the way the option 66 mechanism will function, then yeah, RADIUS VSA for the URL will be the only other way. I think it would be easier to just do RADIUS attributes for all of the config, but we've had that discussion before. Off my rocker now? :) On 9/18/2014

Re: [AFMUG] Dear Cambium

the config, but we've had that discussion before. Off my rocker now? :) On 9/18/2014 8:46 PM, Aaron Schneider via Af wrote: You are securely attached to your rocker and very comfortable. That's pretty much how it will go but the dhcp server will provide the filename via option66 str

Re: [AFMUG] Dear Cambium

f mailto:af@afmug.com>> wrote: That is freakin awesome! I think Matt said something about a RADIUS VSA option too. RADIUS and DHCP option 66. Both are good with me. On 9/18/2014 4:41 PM, Aaron Schneider via Af wrote: Hi George - I know this was a long time ago (and has been an even l

Re: [AFMUG] Dear Cambium

: [AFMUG] Dear Cambium but wouldnt you have to turn on dhcp through the gui for this to pull down? On Thu, Sep 18, 2014 at 4:41 PM, Aaron Schneider via Af mailto:af@afmug.com>> wrote: Hi George - I know this was a long time ago (and has been an even longer time coming), but attached is what

Re: [AFMUG] Dear Cambium

be nice if we could manually apply a config template file directly through the SM GUI, so I can have the guys get new or recovered radios set up without having to mess with too many things (AP, TFTP server, etc), just upload file.. apply, reboot, whatever. On 9/18/2014 10:00 AM, Aaron Schnei

Re: [AFMUG] Dear Cambium

Hi Bill - 1) coming in 13.2 2) coming in 13.2, NAT table size is configurable from 1024 - 8192 entries, there is a configuration OID, and will be a current table size oid 3) possibly coming in 13.3, can't promise that yet 4) coming in 13.3, planning to have something at WISPAPALOOZA to demo, mor