Hi Krishna,
sounds good so far. But as I said when COS 5 is the only COS in Queue 1,
which Traffic/COS could fill T1 and T2 up to 100% when COS 5 is only mapped
to T3?
Regards
Steffen
2012/10/21 Krishna
> steffen,
>
> your approach is not right way of doing it because when u look the
> thresh
steffen,
your approach is not right way of doing it because when u look the threshold
values of the queues you have allocated max threshold is 100 and reserved
threshold is 100, guess what both threshold i.e. t1 and t2 takes up to 100%
value when desired and that being said after t1 and t2 were
Dan & Cory,
thanks for your feedback.. i thought the same but i was triggered by looking at
the ipexpert solutions guide for 5 lab handbook and so taking second thought
from expertise guys like you..
thank you
krishna.
From: Dan Quinlan (daquinla)
To: Cory
yes cory you're correct about understanding the question exactly.
thank you
krishna.
From: Cory Gray
To: Rrcrumm
Cc: Krishna ; Online Study
Sent: Saturday, October 20, 2012 8:23 PM
Subject: Re: [OSL | CCIE_Voice] cme ip add or loopback ip in CUE??
Rand
Cory, I read the question the same way you did. Krishna- either will work if
you're not using "strict match" in telephony service; however, I'd always match
whatever address you use in telephony service. Chances are the lab is going to
specify what address cme phones should use - I'd stay consis
Randall,
I believe the question is when going through the GUI initialization and it ask
for the IP address of CME, what IP address do you use?
Krishna,
Please correct me if I am wrong.
Sent from my iPhone
On Oct 20, 2012, at 9:06 PM, "Rrcrumm" wrote:
> The labs say to use an IP address if 1
The labs say to use an IP address if 10.10.115.2. So under the lo1 you need to
add ip unnumbered lo1(also make sure to add the OSPG statement if needed and
clear the ip OSPG process$
Then add the IP address and default gateway.
Then make sure to add the static route
Hth
Randall
On Oct 20, 201
I have this seen this also, to be honest I think it shouldn't matter
whether it is in threshold 1 or 3 as long as no other COS is in same
Threshold of queue 1 of queset 2. When you leave in in threshold 3 I think
you should be fine with:
mls qos queue-set output *2* threshold 1 100* *100* 75 *100
Hi Cory,
that's the trick. Thanks a lot.
2012/10/20 Cory Gray
> Do you have g729r8 on the transcoder? It is not their by default so you
> would have to add it to the list. I always add it to conferencing and
> transcoder just to get in the habit.
>
> Sent from my iPhone
>
> On Oct 20, 2012, a
I noticed this and I believe it is a typo further evidenced by the note next to
the command that says something to the effect that that command moves it to q1t1
Sent from my iPhone
On Oct 20, 2012, at 2:17 AM, "Pixar Perfect" wrote:
> The requirement is as follows on Lab 2 QOS section of the 5
when using loopback address for CUE setup, does it matter whether what ip
address we put it for cme in cue .i.e. for example loopback 10.10.115.1 or
10.10.202.1(cme ip address)... it works in both the cases but just want to make
sure which one is the right way of doing it..
thank you
krishna
Do you have g729r8 on the transcoder? It is not their by default so you would
have to add it to the list. I always add it to conferencing and transcoder
just to get in the habit.
Sent from my iPhone
On Oct 20, 2012, at 4:32 PM, "Steffen Bruening" wrote:
> Hi,
>
> I have 3 Sites, all of th
Hi,
I have 3 Sites, all of them configured on the CUCM, Site C has Voicemail
with local CUE. When I am dialing from Site B to C codec g279 will be used
and I can reach the voicemail, so I know When I am dialing from Site A to C
through an RSVP CAC Location I get a fast busy when reaching the VM Pi
Voice View is not supported on the AIM Module.
Michael Sears
-Original Message-
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of
ccie_voice-requ...@onlinestudylist.com
Sent: Saturday, October 20, 2012 10:00 AM
To: ccie_voice@online
Kevin,
This is on my lab here at home.
I've trawled the bug toolkit briefly for anything obvious, but didn't
find anything immediately that jumped out at me.
These are the versions.
Phones: 7965Gs Phone load SCCP45.8-4-1S
CUCM Version: 7.0.1.11000-2
AIM CUE Version: 7.0.6
Router: 2811 IOS
Is this on proctorlabs or your own kit? If your own kit maybe a bug in the
specific version, did you check.bug toolkit. Also, which model phones are
you using?
On 20 Oct 2012 08:48, "Peter Simmons" wrote:
> Dan,
>
> I appreciate you coming back to me on this.
>
> I've done that already as part
Dan,
I appreciate you coming back to me on this.
I've done that already as part of the testing (Sorry, this got missed
off in the original message).
I've tried adding ALL the various CTI permissions to the cue jtapi user,
adding all possible permissions, and just leaving it at the "required"
17 matches
Mail list logo