Re: 2501 and ISDN

I have never hung an isdn modem off the back of a router. I have used a BRI before...so my first suggestion is to do that...tyou also have to make sure your serial port is the same on the router and the TA. I dont know if the 2501's serial port is sync/async or not... John Neiberger wrote:

Re: Free Book(let)

HI KELLY, CANT GET THE PAGE YOU HAVE MENTIONED BELOW. PLEASE CHECK IT UP. AMIT Kelly Scroggins wrote: http://www.cisco.com/pcgi-bin/lm/show_form.pl?95910771478430175781251140TEST-100XA ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ,

EOL FOR 25.....

Guys, Tell me boyz, is Cisco about to give a EOL to its 2500 series routers? Amit ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure

Re: 2501 and ISDN

2501's serial port is just sync.. On Fri, 26 May 2000, Blake Traister wrote: I have never hung an isdn modem off the back of a router. I have used a BRI before...so my first suggestion is to do that...tyou also have to make sure your serial port is the same on the router and the TA. I dont

Re: certifications zone

Joe, I've been a member of the group for sometime now and as long as I can remember you've always contributed to this list in more ways than one. Tomorrow is your day in the sun and like everyone else we await your proclamation of success, after all this make me and so many others feel as

Dumb Question

How do I get the router to prompt me for a password when connecting through the Console. It would allow me access to the user prompt without any password. Setting password on Console doesn't seems to work. Thks. ___ UPDATED Posting Guidelines:

Re: EOL FOR 25.....

I don't think so! Bharat Suneja "Amit Mohanty" [EMAIL PROTECTED] wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Guys, Tell me boyz, is Cisco about to give a EOL to its 2500 series routers? Amit ___ UPDATED Posting Guidelines:

Re: Dumb Question

On Sat, 27 May 2000, Jason wrote: How do I get the router to prompt me for a password when connecting through the Console. It would allow me access to the user prompt without any password. Setting password on Console doesn't seems to work. Thks. You also need to set login. en # conf t

Fw: CCNP and chances of finding a job

- Original Message - From: "TyRhon144000" [EMAIL PROTECTED] To: "ken" [EMAIL PROTECTED] Sent: Thursday, May 25, 2000 5:21 PM Subject: Re: CCNP and chances of finding a job Don't feel bad. You just have to persevere that's all. When you try for a job, you should list your skills, what

Re: EOL FOR 25.....

no, but they just announced the 4500, and 4700's are going EOS on Nov 25, 2000. Amit Mohanty wrote: Guys, Tell me boyz, is Cisco about to give a EOL to its 2500 series routers? Amit ___ UPDATED Posting Guidelines:

BCRAN Official Cisco Student Manual

I am looking for the official BCRAN Cisco student manual. I am willing to trade it for either of the Voice class student manuals or the ATM student manuals from Cisco. Please let me know if anyone is interested. Thanks, Dave

Re: EOL FOR 25.....

I've the url at work, not home. It requires Partner CCO access, but i'd be more than happy to attach the html document. it will be monday before i go in. ElephantChild wrote: On Sat, 27 May 2000, Nick Brooks wrote: no, but they just announced the 4500, and 4700's are going EOS on Nov

Re: Calculating bandwidth utilization

One of industry's best bandwidth utilization tools is freeware! Its called MRTG, runs in NT or Solaris. I used it for a few years now. Works great and most ISP's and NAPs use it check out http://www.mrtg.org -Ryan [EMAIL PROTECTED] wrote in message 8gkdfg$uuj$[EMAIL

Re: CCNA 1.0 vs. 2.0

Thanks Ben, I'll check it out ""Benjamin Walling"" [EMAIL PROTECTED] wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... I sat the new course, ICND, and took the old test. There were things like VLANs and switching in the course that were not on the 1.0 test or in the 1.0

Re: Percentage to success

I work with numerous CCIE's and I am one exam (switching) away from my CCNP and CCDP. I would say that the CCNP is not directly comparable to the 'complete' CCIE qualification, rather just the drake test (the first bit). I think it is as follows - CCNA - 5% CCNP or CCDP - 55% CCNP and CCDP -

Re: command to know what type of router or switch it is

Try show ver, show diag, show environment or show controllers - some commands only work on certain platforms... "Stull, Cory" [EMAIL PROTECTED] wrote in message 0D7A05A19CE4D211BD050008C7330FE7098385@CCUPDC">news:0D7A05A19CE4D211BD050008C7330FE7098385@CCUPDC... try show ver.. thats gives some

Re: cannot ping over frame relay

If hte routers can ping each other, thenmy first guess is that your hosts dont have their default gateways set properly. Blake Josh wrote: heres my setup. Host-+R1+--+Frame Switch+--+R2+Host from r1 and r2 i can ping anywhere but from either host i am unable to ping

RE: CCNA 1.0 vs. 2.0

I took the CCNA 2.0 beta (passed) and used Todd Lammle's study guide for 640-407. A couple of months ago Lammle was on brainbuzz.com and suggested a few extra subjects that were on the test. -brainbuzz transcripts- Q: wl1516 Hey Todd,when is you new CCNA book coming out and what is

Any knowledge about this book...

If you read the reviews on the Amazon website, Cisco: A Beginner's Guide by Tom Shaughnessy and Toby J. Velte sounds excellent. I was considering buying it, but would value the opinion of those here if you happen to have read it or know something about it. If it's as good as it seems, it

routing protocol

can someone tell me which port the routing protocols are using ? where can I get the details of all the protocols ? Thanks in advance

Todd's Virtual Trainer

I bought the virutal trainer AFTER passing the CCNA. Although I get to look at 250+ routers everyday at work, I don't have too much to do with configuring them. I've found the simulator to be pretty good, and from what I've seen so far works just like the real thing. I don't know if routersim has

Re: ATM Info

Rik, I think I can help you a bit here as I have a Cat5000 w/ a WS-X5155 and a Sup I (5009 copper) connected to an 8 port MMF LS100 in my lab, so it does work just fine. If you have not purchased them yet, make sure you get newer Sup 1's (there is a difference) as the older boards use a custom

An OSPF toy ???

http://carnap.ss.uci.edu/java/dijkstra/DijkstraText.html check this little puppy out have fun Oz http://www.mcseco-op.com/CiscoStuff.htm ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info:

ppp callback confusion

I'm a little confused about ppp callback, given several key sources of information. Fatkid.com includes a username and callback dial-string global command, however, Cisco docs do not. As well, I have configured dial callback without this global command and it seemed to work fine. Any ideas?

Re: Todd's trainer

WWW.lammle.com oz you were singing the praises of Todd's trainer but neglected to give a URL on where to purchase this item. Can you give me a hand at locating it? ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives,

OFF TOPIC: 3com Switch

Has anyone had any experiance with 3com Superstack 1000 switches? I'm getting a post error: POST error = NET_receive timeout on port 0 Does anyone know what this means? [EMAIL PROTECTED] ___ UPDATED Posting Guidelines:

Re: EOL FOR 25.....

Nick Brooks wrote: no, but they just announced the 4500, and 4700's are going EOS on Nov 25, 2000. Does that include the 4500M as well? Jeff Kell [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives,

Re: Foundry ServerIron

The company I work for has formed a strategic partnership with Foundry, so I am a little biased when it comes to their product line, but.the ServerIron is an excellent product. How many firewalls do you want to load balance?? Jonathan L. CCDA, CCNA, FCNE(Foundry Certified Network Engineer)