Show isdn status then use debug isdn q921 for more detailed information.
Best regards,
Dom Stocqueler
CTO - SysDom Technologies
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
Sent: 03 June 2003 10:33
To: [EMAIL PROTECTED]
Subject: Re: BRI [7:70059]
Hi ppl,
Hello,
Is it possible to convert a custom queueing example into a policy-map
config?
I have:
#queue-list 1 protocol ip 1
#queue-list 1 protocol ipx 2
#queue-list 1 protocol appletalk 3
#queue-list 1 protocol decnet 4
#queue-list 1 queue 1 byte-count 4000 limit 100
#queue-list 1 queue 2
Need to get your PHD first, right?? ;- before you can start doing your
presentations!!
The papers that they write usually are very simple because they break it
down for you...so dummies like me can become real good at it!!
But how about actually developing BGP itself, maybe BGP ver. 5 with
debug isdn q921 is for the layer 2 activity ( for the signalling between the
router and the swith, like TEI, SAPI...)
you can be using:
debug dialer
debug isdn q931 to watch what is going layer 3.
you can check
sh isdn stat -- and see the number of channels occupied
or
sh int bri 0 -- for the
as well as debu ppp multilink
-Original Message-
From: Dom [mailto:[EMAIL PROTECTED]
Sent: 03 June 2003 13:39
To: [EMAIL PROTECTED]
Subject: RE: BRI [7:70059]
Show isdn status then use debug isdn q921 for more detailed information.
Best regards,
Dom Stocqueler
CTO - SysDom
debug isdn q921 is for the layer 2 activity ( for the signalling between the
router and the swith, like TEI, SAPI...)
you can be using:
debug dialer
debug isdn q931 to watch what is going layer 3.
you can check
sh isdn stat -- and see the number of channels occupied
or
sh int bri 0 -- for the
There was only one appletalk quesiton on the NP recert probably from one of
old questions from the routing pool. As for the 700 series nothing like that
on the NP recert. The NP recert exam is one of the more updated newer exams
with ios simulation for hands on testing.
It is the DP recert exam
Sorry De.
Debug q931 is what is needed. It has been about 5 years since I last
touched ISDN thank God!
Best regards,
Dom Stocqueler
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of
Devrim Yener KUCUK
Sent: 03 June 2003 14:17
To: [EMAIL PROTECTED]
Extreme Novice Question
First I would like to say I know nothing about Cisco os, this project was
kind of dumped in my lap..
I have to change the static Nat table.. the one that assigns special
internal ip addresses to static external ip addresses..
Can anyone suggest a place to find easy to
Hi group,
I just got a cisco 3550 smi switch, could someone let me know how to
upgrade the switch to emi ?
Thank you very much...
Philip
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70072t=70072
--
FAQ, list archives, and
Actually a debug isdn q931 would be more pertinent, 921 is your
conection to the switch whereas 931 is call setup. A debug dialer could
also be useful.
Dave
Andrew Larkins wrote:
as well as debu ppp multilink
-Original Message-
From: Dom [mailto:[EMAIL PROTECTED]
Sent: 03
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70076t=70076
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
READ THE FOLLOWING BEFORE DOWNLOADING C3550 SOFTWARE
There are two software images for the Catalyst 3550-24 and 3550-48 - the
Standard Multilayer Software Image (SMI) and the Enhanced Multilayer
Software
Image (EMI). Catalyst 3550 switches
It might not be correct to convert directly from byte count to bandwidth.
You have 4000 + 3000 + 2 + 1000
Queue 1 has 4000/1 bandwidth, which is 40 %
Queue 2 has 3000/1, which is 30 %
You could use 'bandwidth percent 40' for queue 1; or you could use
'bandwidth 102' if your link
Team,
I understand that the 3550 switches at wire speed. Also, it routes up to
the Transport layer. What type of stand alone router could the intergrated
router be compared to?
Thank you,
JoeT (MCSE, CCNP)
Message Posted at:
Contact you salesdude, hand him a check for $1995 minus your discount
and buy CD-3550-EMI!!!
Dave
[EMAIL PROTECTED] wrote:
Hi group,
I just got a cisco 3550 smi switch, could someone let me know how to
upgrade the switch to emi ?
Thank you very much...
Philip
--
David Madland
I suggest u debug ISDN in its entirety.
use: debug isdn ? to see all options for debugging ISDN.
It seems your call setup is taking too long. so monitor the d channel as
well.
See how long it takes for call setup on initial establishment (1st channel).
Then check the time it takes to setup the
Ken,
PIM messages are sent multicast, either to 224.0.0.2 or 224.0.0.13
depending on the PIM version.
PIM Joins are sent periodically, every 60 seconds.
- Tom
[EMAIL PROTECTED] wrote:
Hello,
I have two questions here on the above.
Are PIM joins sent multicast or unicast. Some docs
I had installed a VPN client in home PC to connect to PIX in my company. It
can connect and get authenticated and login. But I can't ping and talk to
any PCs in my company. why?? I specify the IPPOOLS in my PIX config. It
means my VPN client will get these IP right? But how about subnet mask?
I think you are confusing ip policy routing with BGP policy routing. These
are
two DIFFERENT concepts. A BGP routing policy determines what networks a BGP
speaking router can receive or advertise to / from a neighboring BGP
speaking
router ( IBGP or EBGP ). You use BGP neighbor statements to
Watch for wrap:
http://www.cisco.com/en/US/customer/tech/
tk543/tk545/technologies_tech_note09186a0080114326.shtml
neil K wrote:
Can somebody tell me how to configure LLQ on Ethernet subinterfaces
connected to two VLAN's.
Will appreciate it.
Message Posted at:
interface TokenRing0
ip address 192.168.34.3 255.255.255.0
ring-speed 4
source-bridge 9 3 23 What do all these mean?
source-bridge spanning
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70090t=70090
--
FAQ, list
I am always suspicious of mtu differences, or mtu discovery via icmp being
blocked..
Brian
The path to a desireable destination
is often more difficult than the path to stay where you are.
On Tue, 3 Jun 2003, Steven shinnick wrote:
I had installed a VPN client in home PC to connect
interface TokenRing0
ip address 192.168.34.3 255.255.255.0
ring-speed 4
source-bridge 9 3 23 _-- What do all these mean?
source-bridge spanning
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70092t=70092
--
FAQ, list
Robert,
The local Token Ring number is 9. The interface will bridge traffic
from this ring to ring number 23. The Token Ring RIF will indicate the
router as bridge 3.
- Tom
Robert Perez wrote:
interface TokenRing0
ip address 192.168.34.3 255.255.255.0
ring-speed 4
source-bridge 9 3
I hope I don't embarrass my self here, but if I remember correctly:
..the 9 and 3 are the two Rings that you want to bridge, and the 23 is
the bridge id.
Hope my memory served me correctly today.
I'm sure Priscilla will tell us for sure. :)
-Mark
-Original Message-
From: Robert Perez
Interesting way to spend a couple of hours. After reading previous posts on
this topic, I entered the exam with a bit of trepidation. Never enough time
to study. I can't say as the feeling diminished as I took the test. 112
questions, 145 minutes ( including the time for the mandatory tutorial on
Mwalie W wrote in message
news:[EMAIL PROTECTED]
Hi All,
This is just a comment arising after I read a paper in the current IEEE
Communications Magazine.
I was a little surprised. The paper is, of course, a refereed paper and
was
written by three guys, one of them a PhD.
I was surprised
Robert
In your example, the ring number 9 ( int. token 0 of your router ) is
bridged to the ring number 23 ( attached to other int. token ) across the
bridge number 3.
Regards
Juan Carlos
Juan Carlos Ameneiro
IT Specialist
Softnet - Logical
Tel: 4344 0459
Cel: 15 5017 0459
No pudiendo hacer
jeff sicuranza wrote:
There was only one appletalk quesiton on the NP recert probably
from one of old questions from the routing pool.
I think the AppleTalk questions (if you get any) in the CCNP recert are from
the Support exam which hasn't been updated much.
As for the 700
series
Congrats Chuck and to continue the theme,
I have failed the exam enough to get my money back guarantee from Boson.
(in spades)
However, today I passed it - which was good 'cause my cert was to expire on
8 June 2003. Now I'm good for another 3 years.
I too am off to the CCDP recert. I'm due at
well... my experience is a bit different.
As I said in a previous post I've taken this exam a few times.
I encountered both Appletalk and the 700 Router on the NP recert and not
just one question.
I think the question pool is huge on this exam. Consider what it has to
cover.
The
H!!!
I erased my bootflash on my 7505 router...
What do I have to do!!??
Please help my, I will comit suicide
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70103t=70103
--
FAQ, list archives, and
Actually he just turned 100 this last week - so not yet late.
What was that song the late great Bob Hope used to sing?
Thanks for the memories!
Let's see if this post gets through.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70105t=70095
Use a TFTP server with tripwire installed.
All you need is an old PC, a basic linux install and a free version of
tripwire.
Cost is next to nothing.
Erik Mintz
--
From: Stevo
To: [EMAIL PROTECTED]
Subject: Router Configuration Backups?? [7:70009]
Date: Mon, Jun 2, 2003, 12:37 PM
I am a genius,
I copied the rsp-boot on the simm flash on my 2611
I put the simm flash 2600 on my 7505
I put the simm flash 7505 on my 2600
I downloaded a IOS on rommon on my 2600
pppfff, is not documented solutionCisco says to ship in RMA
I dont going suicide... ;-p
Message Posted
Is there a reason that you can't copy from a tftp server to bootflash:?
Geoff Mossburg
-Original Message-
From: Lamy Alexandre [mailto:[EMAIL PROTECTED]
Sent: Tuesday, June 03, 2003 8:51 PM
To: [EMAIL PROTECTED]
Subject: N [7:70103]
H!!!
I erased my bootflash on
Guys,
Is there a way to configure a 10/100 port on a Cat switch as MDI X (cross
connect). So that we can use straight cable to connect two switches...
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70109t=70109
--
FAQ, list
What are you trying to do? You could get a CCNA book or go to www.cisco.com
That would probably do best for you.
Cheers
Shane Lieberg wrote in message
news:[EMAIL PROTECTED]
Extreme Novice Question
First I would like to say I know nothing about Cisco os, this project was
kind of dumped in my
Priscilla Oppenheimer wrote in message
news:[EMAIL PROTECTED]
jeff sicuranza wrote:
There was only one appletalk quesiton on the NP recert probably
from one of old questions from the routing pool.
I think the AppleTalk questions (if you get any) in the CCNP recert are
from
the Support
Ring #s and Bridge #s
Robert Perez wrote in message
news:[EMAIL PROTECTED]
interface TokenRing0
ip address 192.168.34.3 255.255.255.0
ring-speed 4
source-bridge 9 3 23 source-bridge spanning
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70115t=70115
Sure, open up the case on the switch and resolder some connectors. Just
kidding, no you can not do it via softeware. Just make a crossover cable to
do the job.
Cheers
sumitsood wrote in message
news:[EMAIL PROTECTED]
Guys,
Is there a way to configure a 10/100 port on a Cat switch as MDI X
A GSR series router maybe? Is this a test? Did I get it right?
Cheers
Joseph R. Taylor wrote in message
news:[EMAIL PROTECTED]
Team,
I understand that the 3550 switches at wire speed. Also, it routes up
to
the Transport layer. What type of stand alone router could the intergrated
router
Okay gang, what should I study last minute? Anyone give any pointers? I need
to lay the smack down on this next week. Can anyone hook a brutha up?
Cheers
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70117t=70117
--
FAQ, list
Kevin Wigle wrote in message
news:[EMAIL PROTECTED]
Congrats Chuck and to continue the theme,
I have failed the exam enough to get my money back guarantee from Boson.
(in spades)
However, today I passed it - which was good 'cause my cert was to expire
on
8 June 2003. Now I'm good for
Hey!! Do you know where can I download older version VPN 3000 client (ver
2.5) ? I can't find it in cisco website anymore
Thanks!!
Greg
-
Do you Yahoo!?
Free online calendar with sync to Outlook(TM).
Message Posted at:
Priscilla wrote:
One would think it would be easy to use the same pool of questions for
CCDP, but they don't. No BGP or IS-IS for example. SNA and StrataCom
though! Oh boy! :-)
I had quite a few BGP questions in my CCDP-recert exam on Monday.
I am really happy that I am now certified for
Because is not possible in ROMMON on 7505, the router boot only in bootflash.
this command: tftpdnld, xmodem, ymodem and b myimage ipaddress it doesnt
work.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70120t=70103
--
FAQ,
Hi
Can someone clarify why you would use a route-map instead of distribute list?
Thanks in advance,
-DJ
-
Yahoo! Plus - For a better Internet experience
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=70121t=70121
Token Ring uses non-canonical addresses. There shouldn't be a need to swap
addresses if both hosts are on Ethernet.
Priscilla
Azhar Teza wrote:
There is a lot of confusion about running dlsw+ between two
routers. For example, If a there is a peer relationship between
r1 and r2. r1 config,
50 matches
Mail list logo