Does any one know how many questions are on the foundations test. I have
looked on the cisco site but have had no luck.
Thanks in advance
G30RG3
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=24132t=24132
--
FAQ, list
not be on the
lab test.
Just my 2 cents
G30RG3
Louie Belt wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
Here is a quote directly from Cisco website about the CCIE RS Lab:
The Routing and Switching Lab exam tests any feature that can be
configured
on the equipment in the Equipm
You can do it with an external router if you have an 10/100 blade that
supports isl or dot1q trunking. or you gan get an rsm I believe or an nffc.
G30RG3
Thomas wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
Hi All,
I wonder if CAT 4006 switch support MLS? It does
if you have ios version 12.1 or newer then issue the following command
config terminal
interface ethernet 0
ip address dhcp
its that easy
George, Head Janitor, CCNA CCDA
Cisco Systems
KM Reynolds wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
Hello Everyone,
I have an 1605
Just passed my BSCN yesterday and wanted to say that reading over the
questions and replys has helped me gain that extra knowledge needed to pass
the test. As for what questions i got on the test, Without breaking the
NDA, I studied hard on the following subects (hint hint) BGP, Policy based
The reason you cant ping from the router itself is that when you specified
what traffic to encrypt and send to the tunnel you only specified the
subnets behind the firewall and router. If you try and ping the other side
it will not go through the tunnel because it is not a match on the
If no one knowsthe answer, Try sniffing your packets on that segment you
can probably find out.
George, Head Janitor, CCNA CCDA
Cisco Systems
Steve Roman wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
Does anyone know what ports Diablo II uses. Need to block it.
Message
If you read that article it gives the idea that this could stop the internet
from working. Let me just say that if there is an ISP or Tier 1 provider
out there that has http enabled on there router, then they should get hacked
and brought down for being stupid. They make it seem that you need
If you are in a hub and spoke environment and your hub is your as border
router that is getting external routes then by default it will forward all
external routes to its internal BGP neighbor routers. The purpose of route
reflectors is to have internal BGP routers that do not have a interior
You need an isdn simulator
George, Head Janitor, CCNA CCDA
Cisco Sytems
Andrew Lawrence wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
I'm in desperate need of information on how to connect 2 1600 routers
together over isdn.
The networks either side will be different IP
Use access class lists on the VTY terminals and that should work.
George, Head Janitor, CCNA CCDA
Cisco Systems
Steve Smith wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
Hey gang is there any way to lock down telnet to a specific node on a
network like you can a router or
For the 56k csu/dsu you can use a rollover cable(console cable). Make sure
that one router is getting clocking from line and one from internal.
Good Luck
George, Head Janitor, CCNA CCDA
Cisco Systems
Michelle Sanderson wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
I'm trying
Make sure you input the command terminal monitor so it will display the
output to the VTY session you are logged in on. otherwise it will only show
it to the console session.
Good Luck
George, Head Janitor, CCNA CCDA
Cisco Systems
cisco guru wrote in message
[EMAIL PROTECTED]">news:[EMAIL
Daniel
Maybe I am just misunderstanding your answer but you can alter the flash
when the router is booted up normally. If you type the command copy tftp
flash and go through the prompts it will ask you if you want to erase the
flash and put the new one in. By erasing the flash and writing the
What are you using for inter V-lan routing?
On your router use the ip helper command.
Hope this helps
George, Head Janitor, CCNA CCDA
Cisco Systems
Rich Chang wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
Does anyone have any ideas on how to integrate DHCP with VLAN. For
you can use acccess control lists as a starting point, but it would
ultimately depend on what ios you have. if you have the ip/fw ios you can
be more granular as to what to let out and in.
Hope this helps
George, Head Janitor, CCNA CCDA
Cisco Systems
Eric Waguespack wrote in message
[EMAIL
I am currently doing this with a client but i am using the IOS based vpn
Client (cisco secure vpn client) and my tunnel is terminating on a 3640 with
ios ipsec 56. I am using preshared keys. md5 hash and des. on the remote
side I am using nat overload and it does work. I can't attest it will
Priscilla,
The only reading I have done on the LLC2 standard is from a book written by
Roosevelt Giles. From reading the book I got the impression that LLC was a
subset of HDLC and it was based on HDLC standard not the other way around.
I would have to respectfully disagree with the statement
One should say fw1 and the other should say fw2. It is also printed on the
circuit board of your 2500. At least on mine it is. if you got 2 fw1 then
they sent you two of the same.
George Head Janitor, CCNA CCDA
Cisco Systems
Tim Rutherford wrote in message
[EMAIL PROTECTED]">news:[EMAIL
Instead of practicing isdn with a simulator, You can do exactly the same
labs using your async communications (aux Port)
No you cant setup spids but you can do DDR dialer profiles, ppp auth, and
even multilink with two phone lines. and you probably wont spend more than
$150 dollars. Everything
Jason
It depends on yoour clients need and budget. you can do Cisco IOS based VPN
if they have an existing router and use secure remote client to access the
network. That is probably going to be your least expensive route. You can
also go with a concentrator like vpn 3000 it is strictly for
brandon
You have to use DDR and dialer profiles and specify interesting traffic.
Here is a good link to get you started with some sample configs. Hope this
helps.
http://www.cisco.com/warp/public/471/index.shtml#ddr
http://www.cisco.com/warp/public/793/access_dial/async_backup_dp.html
Good
Does anyone know the pinouts or the connectors/cables you would use on the
older 1900 catalyst switch with the DB-9 connector as the console port. I
have been to the cisco site and it seems I can use regular DB-9 connectors
with a rollover cable but it doesnt work. Maybe there is a trick to
test please ignore
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=6957t=6957
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL
24 matches
Mail list logo