Hi all,
while configuring the T1 CSU DSU card we use service-module commands.
Here when I have the following command
service-module t1 remote-loopback {full | payload} [alternate | v54]
The default option is Full and payload loopbacks with standard-loopup codes.
and its mentioned in documentation
Hi
reliability 255/255 means the link that this interface has is 100% reliable,
no problems on link.Ideally this value should be like this otherwise some
problem on link.
Calcualted on scale of 1-255 as percentage
txload 74/255(indicates transmit load on the link)
rxload 14/255(indicated recieve l
th command must
> reflrect the lowest
> cir of the pvc's used.)
> i'm sure others will comment on this
>
> hope the above helps
>
> ""Simmi Singla"" a icrit dans le
> message de news:
> [EMAIL PROTECTED]
> > Hi all,
> > G
Hi all,
Generally what are mostly used in customer scenarios point to point or
multipoint subinterfaces while confguring frame-relay.As U know all point
-to point sub interface consumes lot no.of addreses all different
subnets,although ip unnumbered is way to avoid this(ip unnumbered has the
limit
Thanx for replying back.
Confusion is cleared
Currently going through your book Top Down Design:)
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=61917&t=61829
--
FAQ, list archives, and subscription info: http://www.groupstudy
Hi all,
Generally what are mostly used in customer scenarios point to point or
multipoint subinterfaces while confguring frame-relay.As U know all point
-to point sub interface consumes lot no.of addreses all different
subnets,although ip unnumbered is way to avoid this(ip unnumbered has the
limita
cir]
> [ppp virtual-template-name]
>
> See the Command Reference here:
>
>
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fwan_r/frcmds/wrffr2.htm
>
> So, something is definitely squirelly if you are able to type
> in the broadcast keyword. I'
:
>
> Priscilla Oppenheimer wrote:
> >
> > Simmi Singla wrote:
> > >
> > > Hi all,
> > > Can anybody explain me when i use the broadcast keyword in
> sub
> > > interface(fram-relay interface-dlci 16 broadcast) then if i
> > >
Hi all,
Can anybody explain me when i use the broadcast keyword in sub
interface(fram-relay interface-dlci 16 broadcast) then if i have only static
routing will it affect that.I read that it is used only for OSPF to pass
broadcasts , if multicasting disabled.But In a scenario if I have no dynamic
r
's my 2 cents anyway. (Does that silly idiom translate to
> other languages/cultures? I hope! :-)
>
> Priscilla
>
> Simmi Singla wrote:
> >
> > Hi Dave,
> > Thanx for the reply,but I am still not clear > been revised in the new
LMI specifications that we
letting
> protcools behave in their intended way to hopefully not waste
> router resources.
>
> To be honest, I doubt that most people working in the field
> worry about such things, (not to say that operations types
> aren't graceful. :-)
> ___
I.
> 1-15 and 1008-1023 are reserved.
>
>Dave
>
> Simmi Singla wrote:
> > Hi all,
> > I have read in one of the books and internet also that dlci
> value range is
> > dependent on lmi type configured.
> > Example
> > The following DLCI ranges a
Hi all,
I have read in one of the books and internet also that dlci value range is
dependent on lmi type configured.
Example
The following DLCI ranges are based on LMI protocol:
ANSI: 16 - 991
CISCO: 16 - 1007
Q933a: 16 - 991
But when we configure LMI type as example take ansi so after t
to
> each other.
>
> if you change the encapsulation on the main interface, all
> subinterfaces
> that do not have a preset encapsulation type, will have their
> encapsulation
> type reflect to the changed one.
>
> hope the above helps,
> regards
>
>
>
> &qu
Hi all,
I have read in books that dlci value range is dependent on lmi type
configured.
Example
The following DLCI ranges are based on LMI protocol:
ANSI: 16 - 991
CISCO: 16 - 1007
Q933a: 16 - 991
But when we configure LMI type as example take ansi on cisco router so after
this when we co
Hi All,
Problem 1)
Can anybody explain me cofiguring IETF encap on the main interface and
confguring ietf per dlci on the sub interface,what coul be implications.
My Topology
centrral
router>switch--remote-ends(non cisco)(many cisco
& otherv
Hi all,
Can I make the router as hub too ,suppose my requirement is like that what
ever data comes on one port should come on other,Can we configure span on
router as we do on switch.
Regardsmlehr wrote:
>
> I have studied for and successfully tested CCNA & CCNP and now
> I am studying
> for the C
Hi all,
Can I make the router as hub too ,suppose my requirement is like that what
ever data comes on one port should come on other,Can we configure span on
router as we do on switch.
Regards
mlehr wrote:
>
> I have studied for and successfully tested CCNA & CCNP and now
> I am studying
> for the
Hi All,
a very simple baisc question I have.what is the basic differnce between copy
run start and write memory command(as it was supported in older versions)
Thanx in advance
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=60569&t=60569
-
Hi Priscilla/All,
Thanx for the reply.all are absolutely right when keepalives are exchanged
they are not compressed.i would like to mention here only keepalives.I debug
the o/p
again ,even the cdp frames are compressed.
Like to share the Debug O/P with u all for dummy setup
client-
ent issue.
> >
> > Let me step out on a limb here and postulate that in terms of
> > process, the
> > router first compresses the data, then attaches the HDLC
> frame.
> > Much the
> > same way that when compression is uese on the LAN, the data is
> > compressed,
> >
Hi All,
I have question regarding HDLC,a silly question but still a doubt.See I have
HDLC connection back to back.on one interface I configure compression and
other interface on other router no compression.Now when I debug the my seq
and mine seen no.s are in sync I mean same they inncrease ,that d
Hi Prasicilla
See the min IOS version required to support what i feel is 12.2(8).
It doesnot require enterprise image i think.Ip PLUS will work without any
encryption features and eneterprise features
Example for naming convention
sh ver C2600-ios-M
C2600 platform
ios is feature sets like I define
Hi ,
Wish u every body a happy new year.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59897&t=59897
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure viol
Hi,
inbound traffic has nothing to do with HSRP.It all depends how your isp is
routing back traffic through bgp.so it means u can load balance on the two
links.
Ivan Yip wrote:
>
> Hi,
>
> I have 2 routers configured with HSRP and running BGP with
> single ISP. For outbound traffic, it will go th
Hi,
inbound traffic has nothing to do with HSRP.It all depends how your isp is
routing back traffic through bgp.so it means u can load balance on the two
links.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59737&t=59735
--
FAQ,
Hi all,
How do I configure remote loopback for a E1 link on a cisco Router. I could
do it for T1 using the FDL. But for E1 I can't find any commands for remote
loopback configuration.
Moreover can any body tell me that what these options are
Can U explain me for what these loopback commands on D ch
Hi Greg,
Can U confirm for whom are u posting this .You have not mentioned name also
and who are u
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59643&t=59639
--
FAQ, list archives, and subscription info: http://www.groupstudy.com
28 matches
Mail list logo