I have a noise at my place that comes on at night and is a random pulse type
noise. Essentially on a spec an it looks like a bunch of very narrow spikes
that jump all over the place. A peak hold trace draws a new noise floor by
connecting the spike peaks about 20dB over the actual floor.
In my
Hi David and other group members,
Thank you for all your replies.
I shall try to buy one of those 3.5AH battery first
and give you details later.
There are many many battery manufacturers in China
where we are so near. I shall see what I get.
There may be no weblink for manufacturers who are
Good investigation Scott, ties in with my findings.
Protem I have installed a relay to short the loop pre-amp output
on TX.
73
Stewart G3RXQ
On Sat, 2 Feb 2008 18:22:57 -0800, Scott Prather wrote:
When I read about this report from Stewart last night (as well
as the
responses indicating that
Note. The EWE needs good and consistent ground conditions to work
well.
Stewart G3RXQ
On Sat, 2 Feb 2008 16:19:56 -0800 (PST), WILLIS COOKE wrote:
-Rolf, the best antenna for receiving on 80 meters is
the Beverage if you have the room. Since you need to
stretch a wire for 500 to 1200 feet in
When carrying out the power calibration on the K3, I find that TXGN in
the Config[Tech] menu shows: Pr80 28 when doing the 50W calibration
on 80 metres. It is only on 80m the 50W calibration that I get the
Pr80. On all other bands the Pr80 is not shown and I just get a gain
figure.
Do I
This will change everything. Personally, I don't like the concept, as
it ends (or drastically reduces) a skill set that I highly value.
Technologywhen is it too much?
http://www.dxatlas.com/CwSkimmer/
de Doug KR2Q
PS. Tnx to CT1BOH for the heads-up alert.
They are busy in W6-land. I have received email responses from Lisa
with a 2 day turnaround just this last week.
Gooc luck.
Mike/aj9c
Dr. Werner Furlan wrote:
hello,
if someone from Elecraft staff reads this, I am trying to get an answer from
Lisa or someone in the sales department since
I recall marine transmitters that I sailed with having big resistors from
antenna to ground to prevent static build up. An old hand told me they got
warm when sailing the Indian Ocean.
David
G3UNA
I severely damaged (burned up!) the receive antenna input board of an
FT-1000D once due to
Hello Group,
This group is fantistic. Of course, I got all answers
such as:
1. go for a better antenna;
2. not much difference in dB so don't border the
increase;
3. work better on the compression for SSB.
Naturally, all the above are very good advice. The
most encouraging answer is that a ham
DOUGLAS ZWIEBEL wrote:
http://www.dxatlas.com/CwSkimmer/
Technologywhen is it too much?
Steroids in baseball come to mind.
--
73,
Vic, K2VCO
Fresno CA
http://www.qsl.net/k2vco
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
Hi Doug,
If that works as advertised the search and pounce
technique is now history. It will
be read and pounce . or maybe even read, read and pounce. One
could sit and read a
magazine and just periodically look up and read the screen.
The reality is that it
I just downloaded and installed CW Skimmer on my computer. It is a really nice
program. It easily decodes weak signals and it is obvious an awful lot of work
went into it. The program supports the K3. As a casual CW op I am very
impressed.
On another note, I just installed the KXV3 in my K3
When trying to display the PA or FP temp, the manual says to tap DISPLAY and
use VFO B knob to select PA xxC or FP xxC (pg 48) but when I try this I do
not see either as an option. How do I set these options.
Dave
--
View this message in context:
This will change everything. Personally, I don't like the concept, as
it ends (or drastically reduces) a skill set that I highly value.
Technologywhen is it too much?
http://www.dxatlas.com/CwSkimmer/
Another way of looking at this program is that if you had a Softrock on the
IF output
Dave
You need the tech mode to be on... Undocumented feature!
73 Dave, G4AON
K3/100 #80
When trying to display the PA or FP temp, the manual says to tap DISPLAY and
use VFO B knob to select PA xxC or FP xxC (pg 48) but when I try this I do
not see either as an option. How do I set these
DOUGLAS ZWIEBEL wrote:
This will change everything. Personally, I don't like the concept, as
it ends (or drastically reduces) a skill set that I highly value.
Technologywhen is it too much?
Personally I don't think it will have any impact at all, especially at $75.
-
Julian,
Nice sleuthing work, Scott. I noticed another issue with the KXV3. One
of the first things I did with my finished K3 kit was to look at the IF
output prior to connecting it to my panadapter project. I was mainly
looking to check the overall stage gain from antenna input to IF output.
What I
Simon Brown (HB9DRV) wrote:
2) For anyone thinking about a digital mode interface *please* look at the
usinterface.com Navigator, it is an excellent piece of hardware in every
respect, I just cannot criticise it at all.
What does this allow you to do that you can't with a serial cable
1) an excellent soundcard which is FCC approved,
2) just one cable connects the box to your PC, it provides:
Dual soundcard input
Two serial ports (including CI-V)
K1EL Winkeyer
Input for paddles
FSK via a UART
Monitor the audio
I was *very* sceptical - until it
A few days ago, I discovered some polycarbonate boxes in the camping
section of our local Wal-Mart. They are watertight, have an O ring
gasket around door fitting, clear (with a blue tint), and come in 2
sizes.
I couldn't find them on the WM website, but did find them on the
Outdoor Products
So not a lot, then, except it frees up your existing sound card. It sounds
pretty much the same as the RigExpert, which I sold a couple of weeks ago on
eBay. It was a nice piece of kit but it was useless under Linux, which I'm
the process of migrating to. I guess this box of yours is also
My guess it will appeal to some non-cw or slow cw operators to get on a
contest, so increasing the numbers having a go. More QRM so need for more
K3s amongst those not using it :o)
David
G3UNA
DOUGLAS ZWIEBEL wrote:
This will change everything. Personally, I don't like the concept, as
Brett wrote:
I have a noise at my place that comes on at night and is a random
pulse type noise...
In my Kenwood TS-450S both NB1 and NB2 seem to have about the same
effect on the noise and it does a pretty good job.
But the K1 seems to be completely ineffectual on this noise. Could
it be that
The good thing about a larger capacity battery is that you can operate
longer.
72,
Bill
K9YEQ
K2 #35, K2 # 5279, KX1 #35, Mini Modules, etc. (K3/100 on order!)
-Original Message-
From monetary terms, if K2 can be modified to deliver
25 watts at say US$50, it would be
The ones I bought (not from Wal-Mart) were good against light rain, but
leaked slightly in driving rain, yours might be different, be worth a try.
You could add some compound on the seal to help with this. On mine the O
ring is a bit too hard and the lip a bit too soft to make a really good
I was just chatting with another K3 owner about the merits (or not) of
the K3 tuner. I commented that I have resonant antennas on all bands
except for 75m where my ant is cut for the bottom end of 80m. I
noted that if I set the K3 to 5 watts power and the display and then
transmit (cw), I still
I believe this phenomenon was responsible for my Acom 2000A generating arc
fault errors if I ran 500W on 160M with rx connected to a Beverage that's
about 100ft away in its general direction.
It's still early to say, but the problem seems to have been cured by adding
an ICE 196 RF Limiter in the
Depends on drivers, good luck with Linux, I assume you have a lot of time to
waste.
Simon Brown, HB9DRV
- Original Message -
From: G4ILO [EMAIL PROTECTED]
So not a lot, then, except it frees up your existing sound card. It sounds
pretty much the same as the RigExpert, which I sold a
Technologywhen is it too much?
Not that this really apply to an Elecraft radio, but I couldnt resist to
comment;
First of all, interesting that no one complained about the K3 internal CW
decoder but found the time to question the functionality of this software :)
Technology evolves and
In a message dated 2/3/08 10:02:53 AM Eastern Standard Time, [EMAIL PROTECTED]
writes:
The reality is that it is just one step up from the DX
clusters.
Except that using clusters in many contests will put you in a different entry
class.
The trend towards such automation is not new.
Plus ca change
Some time back, W3FQB (SK) wrote a story called The Man Who Broke The
Bank
about a techno-ham who built a fully automated SS station and proceeded to
make an incredible score. The computer did everything - tuned across all
the
bands looking for new ones, called CQ, made the
Björn said:
First of all, interesting that no one complained about the K3
internal CW decoder but found the time to question the functionality
of this software :)
Well, Björn, the K3 decodes one signal at a time and the Skimmer
decodes and analyzes (identifies the callsign of who owns the
David, G4DMP wrote:
When carrying out the power calibration on the K3, I find that TXGN
in the Config[Tech] menu shows: Pr80 28 when doing the 50W
calibration on 80 metres. It is only on 80m the 50W calibration
that I get the Pr80. On all other bands the Pr80 is not shown
and I just get
I was able to duplicate your findings, Scott. My setup is a little
different though... K3 output to spectrum analyzer through 100W/50dB
attenuator. RX IN connected to signal generator with adjustable output.
I found the noise in the transmitted signal to appear at +20dBm as well,
although mine
If I add the KPA-100 to my K2 and then the KAT-100, what happens to the auto
tuner that's in my K2? - tnx - Bruce.
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change,
When fitting the KPA100, any of the items normally fitted in the QRP version
lid (KI02, KAT2,
battery) are removed (including the lid). The KPA100 occupies the space they
formerly resided
in. The normal layout is to fold the K2's tilt bail and stand it on top of the
KAT100.
You end up with
Bruce Rattray wrote:
If I add the KPA-100 to my K2 and then the KAT-100, what happens to the auto
tuner that's in my K2? - tnx - Bruce.
You keep the QRP lid with the tuner in it so you can switch them if you
want to take your K2 camping.
--
73,
Vic, K2VCO
Fresno CA
http://www.qsl.net/k2vco
Johnny Siu wrote:
Again, thanks for all your answers. Now, I need to do
one thing - buy a 3.5AH battery and come back to this
group again for more details of the battery.
If you could get double the power out with the same battery voltage you would
be increasing your current draw from the
Hi all,
I'll address both of these issues.
1. RX ANT input signal handling during TX
The KXV3's ANT IN jack includes a carrier-operated relay circuit (COR).
If the COR kicks in too soon, they relay will switch off/on during
keying. So its threshold is set high. It will still serve its
Actually it is documented on pg 34, but it doesn't say explicitly that PA
FP temps are shown only in tech mode, it just says additional displays will
be available.
On 3/2/08 15:55, Dave G4AON [EMAIL PROTECTED] sent:
You need the tech mode to be on... Undocumented feature!
73 Dave, G4AON
I was interested to read recent comments on 160M receive antennas. As it
happens, I just completed a coaxial loop antenna for my K2 this weekend, as
described by KN4LF and KC2TX, and combined it with their recommended preamp.
It's the antenna design that's been in the handbook for years. I've
Hi Parker
I think it depends on the noise source. If it comes from one
direction, a loop antenna can be rotated to place its null on the
noise source, improving the signal to noise ratio for the signals
coming from other directions.
On the other hand, if your noise is more pervasive, and turning
Its a shame you had to go there Simon. My experience with Linux and
Unix is, it just works. Completely different from my experience with
windows. Obviously biased, but well said.
http://www.vanwensveen.nl/rants/microsoft/IhateMS.html
Haven't heard of any Linux Botnets out there...
Bruce,
If you mount the KPA100 and/or the KAT100 in an external enclosure, the
KAT2 will be locked to ANT1.
If you place the KPA100 in place of the QRP K2 top cover, the KAT2 will
not be present.
73,
Don W3FPR
Bruce Rattray wrote:
If I add the KPA-100 to my K2 and then the KAT-100, what
I received my invoice today from Lisa. Once again,
it's a Sunday afternoon in Aptos and she's working
away. The order to be shipped is as follows:
K3/10
KPA3 - 100 Watt Upgrade
KFL3A-200 200Hz - 5 Pole
KFL3A-500 500Hz - 5 Pole
KXV3 - Xvtr Interface w/RX Antenna In/Out Jacks
I ordered on May
K2 folks,
I am getting to start building my K2. (I was putting the errata notes
into my manual tonight.)
As I am looking around I don't seem to notice any AF audio out
connection. That seems a little odd given all of the features and
functionality that this system has. Am I missing
UPDATE
Funeral Details :
Morris and Morris Funeral Directors
199 Kamo Road
Whangarei
Thursday 1.30 pm 7th February (NZDT)
Any messages and cards should be sent to:
Willcocks family
35 Puriri St,
Kamo
Whangarei 0112
NEW ZEALAND
Peter ZL1PWD
On Sun, 03 Feb 2008 21:26:32 -0600, John Hoaglun wrote:
As I am looking around I don't seem to notice any AF audio out
connection. That seems a little odd given all of the features
and functionality that this system has. Am I missing something
obvious here because I am new to this radio and
Good Evening,
Another fine set of nets. Until Pete mentioned there was a game about to
start I had totally forgotten the event. However, since Green Bay was not
participating it could not be much of a game ;) One of the teams is trying to
beat the perfect record of the Miami Dolphins but
I believe a similar article appeared in QST in the late 1960's.
Steve Brandt N7VS ex: WB6VVS, WN6QYP Portland, Oregon
Some time back, W3FQB (SK) wrote a story called The Man Who Broke The
Bank
about a techno-ham who built a fully automated SS station and proceeded to
make an incredible
In a recent message, wayne burdick [EMAIL PROTECTED] wrote ...
I asked about
When carrying out the power calibration on the K3, I find that TXGN
in the Config[Tech] menu shows: Pr80 28 when doing the 50W
calibration on 80 metres.
You said
PR80 means preamp in use for 80 m transmit
51 matches
Mail list logo