Sometime soon I mean to program my K3's Pig Knob to do what I'd like, rather
than the factory defaults. If someone who is adept with using ASCII on the K3
is willing to help, I would appreciate meeting you off-list.
Requirements - the patience to put up with someone (me) who knows niente about
The weekly Elecraft SSB net meets Sunday at 1800Z on 14.3035 MHz. See you
there.
73,
Phil, NS7P (Oregon)
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
OK what did I do ? Been working on cw and external noise canceller for
couple days - and just tried to listen for the TI9 on SSB - both main and
sub rx are dead. All other modes fine , Just USB or USB dead - all bands
absolutely not a trace of audio - did a couple on -off cycles no joy .
The
For Sale KX3 with accessories. I haven't used my KX3 as much as I thought I
would, so it is for sale. I have a K2 and a k3 which I use more.
KX3
power cable
usb cable
KXFL3 Roofing filter
KXAT3 Antenna tuner
KXBC3 Internal battery charger and realtime clock
MH3 Hand mike
KXPD3 CW key
end panels
Thank you Joe. That is a good suggestion. However I have checked and as far
as I can tell there is no conflicting PTT actions. I also use DATA A as the
recommended mode in the KX3 and do not use VOX. I believe that PTT is either
via RigCAT or Hamlib, and no PTT port is provided in the Fldigi
This is easily repeatable on CW.
I have the 2.8 in slot 4 and a 400 hz filter in slot 2.
If I turn the bw down into the 400hz slot 2 position and Xmit. The amp
will fault out with an error 6.
I noticed this in the RTTY contest too but never figured it out.
I wonder if I should try a
Fault #6 appears to be 'Excessive Driving Power' so it probably wouldn't
hurt to run the TX Gain Calibration again, make sure PWR SET in the menu
is set for Per Band, then check the power settings with the KPA500 on
each band in operate mode.
Although I'm not sure why it would only do it
Is it necessary to remove the KRX3 to install both synthesizer boards and
their corresponding TMP cables? Thanks. Roy Morris W4WFB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I am pretty sure that the question about ASCII programming was about the ASCII
protocol to Elecraft rigs. That truly is ASCII, complete with control
characters.
And yes, I know about Unicode and UTF-8. I was doing multibyte character set
programming before Unicode.
I’ve done some Elecraft
I have the 2.8 in slot 2 and the 400 in slot 4...
Sorry about the mixup.
Mike W0MU
On 2/21/2015 2:56 PM, W0MU Mike Fatchett wrote:
This is easily repeatable on CW.
I have the 2.8 in slot 4 and a 400 hz filter in slot 2.
If I turn the bw down into the 400hz slot 2 position and Xmit.
No it is not
I just installed mine today
From: Roy Morris w4...@carolina.rr.com
To: elecraft@mailman.qth.net
Sent: Saturday, February 21, 2015 11:48 PM
Subject: [Elecraft] Installing New Synthesizer Boards
Is it necessary to remove the KRX3 to install both synthesizer boards and
ASCII? That is a character set that is a subset of Unicode, which is now used
on all modern computers. It isn’t something you program with, it simply
represents characters. On the Mac we do not use ASCII coded characters, but
rather Unicode characters, usually coded in UTF-8.
What is it that
ASCII...
Well, the UTF-8 character set is indeed designed to be backward compatible with
ASCII but it is far more than that -- and even these days many programmers do
have trouble with UTF-8. Why? Because UTF-8 is a multi-byte, variable length
character encoding system. Sure, the backward
Another customer who just did the installation tested transmit close-in phase
noise before/after
and saw pretty dramatic results. At ± 0.5 kHz from the carrier, the new synth
was down about -133 dBc,
while the old was down about -115 dBc.
Does the new synth use the same chip as the KX3? It's
When I attempt to update my rig I receive a message does not appear to be an
elecraft. I have updated to the newest config utility. I have updated
successfully many times since I have had the unit. This message appears with
every attempt. I would really appreciate help with this problem.
All the talk about split has made me want to build a quick split macro
or memory button.
I started to read the manual but its not making sense to me. I guess
some stuff I just need some help to learn.
Anyway what I think I want is to set up a macro button that would do the
AB double tap
HI Wayne
Anyway, a useful indication could be the split (i.e +1.50) offset instead of
the VFO B frequency (user choice based on the DISP status). This is rarely
done by manufacturers (I know the TS-990 which does this) but this is very
useful in practice and avoids mental calculations.
73,
What is the message you are seeing?
73,
Jim KA2RVO
On Sat, Feb 21, 2015 at 12:41 PM, Larry McCreary lrmccre...@earthlink.net
wrote:
When I attempt to update my rig I receive a message does not appear to be
an elecraft. I have updated to the newest config utility. I have updated
message is does not appear to be an elecraft.
On Feb 21, 2015, at 12:49 PM, James Austin ka2...@gmail.com wrote:
What is the message you are seeing?
73,
Jim KA2RVO
On Sat, Feb 21, 2015 at 12:41 PM, Larry McCreary lrmccre...@earthlink.net
wrote:
When I attempt to update my rig I receive
Go to the manual and do the hard reset, then try to reload the firmware. I
had to do this to my KX3 recently when it locked up completely. Involves
removing power, removing one battery, re-installing battery, etc. It's in
the manual.
Good Luck
73, Bill, WD8JWJ
--
View this message in context:
And in order to make the user interface properly user friendly, we could have a
CONFIG item to set the shock voltage so that the operator suffers unbearable
pain rather than death :-)
73, Quin G3WRR
From: Mitch Wolfson DJØQN dj...@gmx.net
To: Joe
From the K3 Owner's Manual ver D10 pg 29:
SSB/CW VFO Offset
The K3 can automatically offset the VFO frequency when you switch
from SSB to CW mode, so other stations will hear the correct CW
pitch. See CONFIG:CW WGHT for details.
For CONFIG:CW WGHT See page 55 of the Owner's Manual
73,
Guys,
with new synt there is any advantage other than better ppm to use external OCXO
source, I was thinking if anybody tested and external 10MHz super clean source
maybe with a Wenzel or a Morion and got any better phasenoise than default
TXCO... is a cleaner OCXO is directly translated in
After my initial report of no obvious difference in the receiver
performance after first installing the new K3 synthesizers, I've now had
the pleasure of using them in the ARRL CW DX contest on 40 meters last
night. Let me preface my observations by saying that I normally run my
DSP at 150 Hz
My friend had his K3 repaired at Elecraft and upon return, LSB is no longer on
the same frequency as CW and USB is no longer on the same as CW-R as his other
K3 is. Seems I remember way back in a previous release note where that could be
set. Anyone know where to set this?
Thanks
Terry
If I understand you correctly, I think you are looking at the VFO OFS setting
which is hidden in the CW WGHT menu on page 55 of the manual.
73
David Anderson GM4JJJ
On 21 Feb 2015, at 13:47, KD8NNU gold...@charter.net wrote:
I would love to know if there is a setting for this also.
I would love to know if there is a setting for this also.
Thanks
Don
Sent from my iPad
On Feb 21, 2015, at 8:19 AM, w8z...@verizon.net wrote:
My friend had his K3 repaired at Elecraft and upon return, LSB is no longer
on the same frequency as CW and USB is no longer on the same as CW-R
Thanks everyone for the replies I now have them built and working.
Cheers
Don
~73
Don
KD8NNU
FH#4107
-.- -.. ---.. –. –. ..-
On Sat, Feb 21, 2015 at 3:00 PM, Brendan Minish wrote:
Hi Don,
macros are a great feature. As you are building them you can test them
with the Elecraft utility and
Ok more reading and searching the internet has got me started. I see
you need to use the elecraft utility to make a macro and assign it to a
memory button. I was trying to figure out how to do it using the radio
front panel.
~73
Don
KD8NNU
FH#4107
-.- -.. ---.. –. –. ..-
On Sat, Feb
Hi Don,
macros are a great feature. As you are building them you can test them
with the Elecraft utility and when you are happy you upload them to the
radio
you can set up a macro for anything you can define as a series of
commands.
take a look at the K3 programming reference guide to see what
Installed the KSYN3A synthesizer today, it was pretty easy.
Used earlier post idea of installing on op desk without disconnecting all the
rear cables, used good static protection.
Only slight problem was the long leads on the mini connector (page 11). I
trimmed them but when installed they
Here's a simple one. I'll explain it and then tell you how to assign it
to a button.
SWT13;SWT13;FT1;UPB5;SB1;
This does the following:
SWT13;SWT13; A-B, twice
FT1; SPLIT on
UPB5; VFO B up 2 kHz (yes, it's not a typo. The 5 means 2 kHz)
SB1; turn on the SUBRX
Of course if you don't have a
32 matches
Mail list logo