Reuben,
I think Rob Sherwood answers this question best with his receiver
ratings. Google Sherwood labs.
Dick, n0ce
On 7/3/2016 4:44 PM, Reuben Popp wrote:
Hey everyone, happy early 4th to you and yours!
I'm looking for a bit on input here. I've had my K2 now for quite some
time now; built
I would like to be able to get rid of the AA cell holders inside the KX3,
and go with a battery pack similar to the KX2. LiFePO4 would be a nice
choice in a battery. For instance, I am very happy with Bioennopower
products, www.bioennopower.com Something similer would be very nice. Wayne
could writ
I have to say that I have been totally satisfied with my two AOC
monitors, don't recall the model but the one was for my computer and
it cost around 110 shipped. It's a 12V monitor and has its own quiet
switching supply like a laptop uses. Incredibly low power requirement
and it's great to look
The K3S is a top of the line, world class radio. If you can
afford it, it will not disappoint you, even if you only use if
for listening.
If you want a cheaper, simpler radio, the Elecraft KX3 rates
nearly as high as the K3S on receive[1] for less money and
complexity. It is much more portabl
I just bought K3S in last 30 days. So new I don't know how to use all
features.
K2 100, transverters, KX3, PX3, KPA100, KX1, K1,all in boxes and cases now.
Just my KX2 is still is in use because I have not figured out how to carry
the K3S around.
Leroy AB7CE
-Original Message-
Fro
On 7/3/2016 7:38 PM, Fred Jensen wrote:
I'm sort of with Joe for higher current stuff ... terminals and
screws.
No screws ... bolt studs and *nuts* - like the terminals on the
Astron RS35A/RS50A/RS70A, etc. I want connections that support
a properly sized ring terminal that can be tightened w
On Sun,7/3/2016 10:23 AM, Charlie T, K3ICH wrote:
One more reason to NOT use power-poles.
Did I mention that I don't like them?
They are hard to use, over-rated, unreliable and not re-useable.
YMMV. I've been using them since I got my K2 around 2003, and love them.
I'd guess that I've install
Bill,
The fact is that the receive filters can be configured for whatever you
want.
Of course, it is not productive to enable a 400Hz filter for SSB or AM,
but the check boxes will allow that if you desire.
Use some sense, and configure the filters that you have installed in
your K3/K3S in a
I always used Molex connectors, they seem to work well. I switched to
APP's when it seemed everyone was, I have the WMR crimper and haven't
had any problems but then, I don't move my radio around much. I'm sort
of with Joe for higher current stuff ... terminals and screws.
I know -- KID: "But
While cleaning out a closet, I came across the Top Cover, Front Panel, and Heat
Sink panel from when I long ago built a KPA100 + KAT100-2 in an EC2.
They are in good condition. Find a picture here:
https://www.flickr.com/photos/8377240@N08/28068372495/
They're free, just pay for postage from
Leroy,
I believe the "change" you request is already available, it just takes
some understanding of the difference between Diversity mode and the
subRX in non-diversity.
When the K3/K3S is in diversity mode, the operation is just like a
single receiver - both the main and subRX work from VFO
I believe these are what you are thinking of:
http://www.neutrik.com/en/audio/powercon/
On Sun, Jul 3, 2016 at 6:39 PM, Edward R Cole wrote:
> I only have power-pole's on my K3/10 and KXPA-100.
>
> I installed a power-pole on the CCI 140w linear I built, but would not do
> it a second time. No
I only have power-pole's on my K3/10 and KXPA-100.
I installed a power-pole on the CCI 140w linear I built, but would
not do it a second time. None of these power-pole will stay seated
if equipment is physically moved.
I very much like the power connectors used by DEMI on their
transverters
Seems a solution looking for a problem. In diversity both Rx are
slaved to VFO-A.
I use diversity on 2m eme to receive two polarities simultaneously
and can select Rx frequency up to +/- 45 KHz of the setting of
VFO-A. To transmit on the selected Rx frequency I operate split Tx
using VFO-B.
Checked the Elecraft site and didn't see any option to download a manual. Is
there one and I missed it? Only noticed the chance to download a data sheet.
Happy 4th to all.
73,
Art KZ5D
__
Elecraft mailing list
Home: http://mailman.qth
Thanks Joe. Got it figured. I had a switch set wrong. It pays to actually see
what the display says. Decoding fine. Doug K6EY
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/m
Yes, and it does produce a tone noticeably closer to a sine wave. However, as a
"certifiable" O.T. for years my transmit sidetone was just the squawks, bleats
and thumps the receiver made when the transmitter overloaded it before I
graduated to a homebrew oscillator that produced a sawtooth outp
What Don says is right on! I have K2/100 #380 and
have done all the mods -- and they were all worth
doing :-)
73, Phil W7OX
On 7/3/16 2:19 PM, Don Wilhelm wrote:
Frank,
That mod is not for all K2s - the K2 design was
changed to produce a more sine-wave sidetone.
Look closely at the infor
Hey everyone, happy early 4th to you and yours!
I'm looking for a bit on input here. I've had my K2 now for quite some
time now; built it myself and love it still to this day. But, because
every guy and gal needs a new radio every now and then, I've got that itch.
I've had my eye on a K3 probab
Being a bit of a tightwad, I picked up an ACER S201HL 20" monitor on sale
($60 IIRC). Works FB for me. Been using it for four years now.
The 20" size is a comfortable reading size for me with the monitor three
feet or so away.
Some will say it is not possible to have a monitor that is "too big"
I have a pair of P3's driving a pair of 23" diagonal measurement
monitors, running at 1440 x 900 resolution, which is the best
compromise of responsiveness and granularity. I think that size
monitor is just about right, especially for displaying large
segments of the band. For example, in a C
Frank,
That mod is not for all K2s - the K2 design was changed to produce a
more sine-wave sidetone. Look closely at the information below.
If your K2 serial number is lower than 3000 - *and* you have not
installed the K2ATOB mod kit, then that can be a worthwhile change.
Be aware that this
(I put the Kx3 in USB, hit data and set it to 45baud AFSK A and
decodetext.)
You are *inverted*. Select AFSK_A instead of USB - that will put
you into *lower sideband mode* which is the traditional "sense"
for RTTY.
AFSK traditionally uses 2125/2295 Hz tones (or 1275/1445 Hz) with
the lower
Don't monkey around with a bad power cable. If you do not have tight
(low resistance) connections capable of carrying the full current, they
will overheat and can be a source of a fire.
My recommendation is to replace the APP connector with another (or buy
an assembled cable).
You *may* be
Hi, Even following Kady's book, I can't get the KX3 to decode RTTY this
weekend. Does anyone have hints on the setup? (I put the Kx3 in USB, hit data
and set it to 45baud AFSK A and decode text.) With lots of tuning, I get
gibberish. S meter is in dual peak mode. Thanks for any help. de Doug K
So I have had some quality time with my K2 this weekend.
I am thinking of doing this modification to my sidetone, has anyone tried it?
http://qrpzone.com/elecraft-k2-side-tone-mod/
Seems pretty easy to do and I have always thought it was “my ears”.
Comments?
Frank KG9H
_
Subject says it all. Looking for a clear recommendation for
a decent monitor that will last. Also what is too small and
what is too big and so a waste of room?
One side of me tells me anything that will display text well
will display the P3 signal but another side tells me "Don't
assume !!)
Hi Guy,
Small wire in center pin connector - no change. No burr on the
connector. Connection feels normal - not too hard or too easy. Center
pin receptacle not spread. 50 ohm connector.
I did make a test lead with a BNC female connector on one end and the 2
pin Molex on the other and hook
It just sounds, walks and talks like a BNC problem.
Try a small guage wire about 10 foot long directly inserted into the
center pin connector, and retry. See if the SWR comes down to some
degree, if you hear anything on RX. If so, then for whatever reason,
the cable BNC pin is not making contact w
for up tp 5 amps so I like RCA Phono Plugs inex,,, cant reverse them,,
makes it hard for other folk to borrow your gear really !
Bob K3DJC
On Sun, 3 Jul 2016 11:05:28 -0700 Bill Frantz
writes:
> [New subject in an attempt to avoid topic drift.]
>
> Several people have said that they d
Thanks Matt,
I did check both connectors and they are both seated.
73, George W5AGK
On 7/3/2016 11:56 AM, Matt Zilmer wrote:
Hi George,
You should check the two RF cables to make sure they're seated. There
is one cable from the ATU to the RF board (two-pin connector at the RF
board), a
Thanks Guy,
I checked my connector and in fact tried two other coax leads - all with
the same result.
73, George W5AGK
On 7/3/2016 1:05 PM, Guy Olinger K2AV wrote:
May not apply in your case, but male BNC connectors can sometimes have
the center pin retracted a bit. This can cause the co
Well at least it's not "Finding True North" again on TowerTalk. :>)
You have not suffered endless threads until you have to filter out
the words "true north" in any email.
73, Guy K2AV
On Sun, Jul 3, 2016 at 2:29 PM, Milverton M. Swire via Elecraft
wrote:
One more reason to NOT use power
Hi Leroy,
When you place the rig in diversity, both receivers run directly off
the main (VFO A) synthesizer, period. If you are in diversity and TX
on your RX frequency, VFO B is not being used for anything.
VFO B remains independent so that such as split operation is possible.
Having VFO B hard
>>> One more reason to NOT use power-poles <<<
WELL! This post has now morphed into another Rendition of " Power Poles "
(((73))) Milverton / W9MMS
From: "Charlie T, K3ICH"
To: elecraft@mailman.qth.net
Sent: Sunday, July 3, 2016 12:23 PM
Subject: [Elecraft] FW: Well Hell I just b
On 7/3/2016 2:05 PM, Bill Frantz wrote:
[New subject in an attempt to avoid topic drift.]
What power connectors do people actually like?
1/4" or 3/8" threaded studs (bolts) for any circuit drawing more than
10 A peak. Certainly *never* a single pin, friction fit connector for
anything more t
Hello,
Solar activity has slowed providing us with fewer ions each day.
The solar flux index is around 70 where it had been sitting around 100
for much of the year. Propagation is OK if you can work around the
noise. However, conditions during the night of FD were great. Noise
was ver
Is your K3/K3S firmware at MCU 5.50 / DSP 2.87, 5-17-2016?
That appears to be *required*. The K3 program internals need the
firmware code that knows what a Kpod is and how to use it.
73, Guy K2AV
On Sun, Jul 3, 2016 at 2:00 PM, Bill Steffey NY9H wrote:
> did the 6 ohm mod, pwr to the pod is goo
Bill
go back to the shop and verify you have latest FW in that K3 !!!
ok, good idea
bill
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecra
May not apply in your case, but male BNC connectors can sometimes have
the center pin retracted a bit. This can cause the connection to just
barely fail in some female connectors and not in others.
PROVE that external connections are not the problem before tearing
apart the rig or sending it back
[New subject in an attempt to avoid topic drift.]
Several people have said that they don't like Powerpole power
connectors. I like them quite a bit, given their flexibility and
ease of use. I will note that the proximate problem that started
this thread again was a bad solder joint, which does
So what do recommend?
Ken - ke4rg
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
Charlie T, K3ICH
Sent: Sunday, July 3, 2016 1:56 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] FW: Well Hell I just bricked my K3s
How are they re-useab
did the 6 ohm mod, pwr to the pod is good...
leds light for the different tuning vfos..
but no vfo movements on the radio///
something does go beep when I plug in /
ideas
bill K3 sn 2244
__
Elecraft mailing list
Home
The eternal lesson, which most of us cannot convince our emotions to
believe in the time of trouble, is that most problems are not the rig
per se, but lie in all the stressed connections, etc.
*IF* I remember at the time of trouble, that the problem is likely
elsewhere, I STILL have to almost bite
How are they re-useable once they're crimped?
I guess you could maybe pry the crimp apart. (??)
Chas
-Original Message-
From: Ken Arck [mailto:k...@arcomcontrollers.com]
Sent: Sunday, July 03, 2016 1:34 PM
To: Charlie T, K3ICH ; elecraft@mailman.qth.net
Subject: Re: [Elecraft] FW: Well
I don't like them either.
On 7/3/2016 10:23 AM, Charlie T, K3ICH wrote:
One more reason to NOT use power-poles.
Did I mention that I don't like them?
They are hard to use, over-rated, unreliable and not re-useable.
Charlie k3ICH
_
I thought I would close the loop on this issue.
It turned out that my "fix" last Fall was just a partial or temporary fix
and the BFO did, in fact, continue to drift. So, I finally went ahead and
did the procedure which you recommended, which I hesitated to do at the
time. I removed L33 and refl
On Sun, Jul 3, 2016 at 10:49 AM, lmarion wrote:
> Check power supply is No 1 on every trouble shoot chart.
>
That's the truth! A couple of years ago, my K3 would start, everything
seemed to work FB, but when I would turn on my computer the K3 would shut
off. Of course I thought somethin
They're reusable but I agree. I have never been a fan
Ken
At 10:23 AM 7/3/2016, Charlie T, K3ICH wrote:
One more reason to NOT use power-poles.
Did I mention that I don't like them?
They are hard to use, over-rated, unreliable and not re-useable.
Charlie k3ICH
-Original Message-
One more reason to NOT use power-poles.
Did I mention that I don't like them?
They are hard to use, over-rated, unreliable and not re-useable.
Charlie k3ICH
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
lmarion
Sent: Sunday, July 03, 2016 11:
Hi George,
You should check the two RF cables to make sure they're seated. There is
one cable from the ATU to the RF board (two-pin connector at the RF
board), and another from the BNC socket to the ATU. Both of these need
to be seated in order for the KX2 to work. The 25.4:1 SWR indication
I just received my KX2 and really like it. I have the ATU and battery
installed. Receive works fine, but I cannot transmit. When I press PTT
I get several beeps and in some cases the radio shuts off. Sometimes I
get a Hi CUR message. Here is some data:
7.213 MHz,Voltage 11.7, Power
On Sun,7/3/2016 9:11 AM, Bill Frantz wrote:
The 12VDC OUT RCA jack (lower left side of the back panel) turns on
when the K3 is turned on and goes off when it is turned off.
Yes. I use it to drive a relay that switches power to a lot of shack
accessories, like antenna switching relays, a Bever
All of the RADAR and beacon systems I worked on before I retired from the
FAA
used diversity receive. I could see the video clean itself up , but it was a
subtle.
I did not expect the diversity receive to work excellent like it does on my
K3S.
I was a little hesitant to get the SUB rece
The 12VDC OUT RCA jack (lower left side of the back panel) turns
on when the K3 is turned on and goes off when it is turned off.
The KEY OUT RCA jack (lower right) allows you to switch
accessories with the change from receive to transmit. I believe
it goes to low resistance when the K3 goes in
On 7/3/2016 10:49, lmarion wrote:
Another teaching moment: Check power supply is No 1 on every trouble
shoot chart.
Or: Check the simple stuff first.
Now, why do I keep forgetting that?
73,
Scott K9MA
__
Elecraft mailing list
Ho
On 7/3/2016 11:09 AM, GW4DVB wrote:
> Just a quick question on the 3 12 VDC OUT (Switched)
>
> Is it really switched? - I'm only asking as it seems to be permanently
> sitting at 13.8V
Yes, it is switched with the POWER switch on the K3.
If you look at K3 RF Board (3 of 4) schematic, the feed t
The 12VDC output turns on when the K3 is powered. When you turn power
off the K3, it should also turn off.
If yours behaves differently, there is a problem.
73,
Don W3FPR
On 7/3/2016 11:09 AM, GW4DVB wrote:
Just a quick question on the 3 12 VDC OUT (Switched)
Is it really switched? - I'm on
What a relief!! I love my K3S, and hope every ham has the pleasure of a
high performance rig.
Another Elecraft superior moment, it did not destroy itself and waited for
the oops moment to pass.
Another teaching moment: Check power supply is No 1 on every trouble shoot
chart.
Congratulati
Thanks to all who replied to my plea for help!
I did find the problem this morning and man, it was not what I
expected. The problem turned out to be that power was not getting to
the radio. Well,,, actually it WAS getting to the radio - to the
Power Poles - but no further. I decided to poke a
Just a quick question on the 3 12 VDC OUT (Switched)
Is it really switched? - I'm only asking as it seems to be permanently
sitting at 13.8V
I am trying to switch off an accessory on keying the K3 ... is there another
way ?
Thanks
--
View this message in context:
http://elecraft.365791.n2.na
Only one filter is used at a time. They are not cascaded. Check all the boxes
for which the filter might be useful. K3 firmware selects the crystal filter
based on the bandwidth you choose with the width knob, from those filters you
choose to enable for the mode you are in.
For example, if you
In the utility, you tell the K3 which filters are installed. They kick
in when you narrow the DSP to within their range. You can select when
they kick in in another setting.
Buck
k4ia K3 #101
Honor Roll 335
8 Band DXCC
On 7/3/2016 10:23 AM, Bill Leonard N0CU wrote:
I am uncertain on how to
I am uncertain on how to configure the radio's filters using the K3 Utility.
I have the 6 KHz & 2.8 KHz filters. I am totally confused by Cady's book,
which shows (pg 27) almost all of the ENABLE boxes checked. This doesn't
make any sense to me since I doubt the hardware can be configured with all
If anyone interested, I have a k3/0 mini available with cable set, can ship
it worldwide or bring it along to US (Texas) end of the summer. Would
consider KX3 swap.
Drop me mail if interested.
Johan, ON4IQ
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-0-mini-availabl
65 matches
Mail list logo