RE: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

Thanks! 73 de Dick, K6KR -Original Message- From: Joe Subich, W4TV [mailto:w...@subich.com] Sent: Saturday, December 27, 2008 7:02 AM To: 'Dick Dievendorff'; elecraft@mailman.qth.net Subject: RE: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W,and 1 mW Dick, &g

RE: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

kenk...@cox.net] Sent: Saturday, December 27, 2008 6:36 AM To: Dick Dievendorff Cc: 'Dave G4AON'; elecraft@mailman.qth.net Subject: Re: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW Hi Dick: I just tested here and if power control set to any 5.x >

Re: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

1 milliwatt (on each band) before any transmission. 73 de Dick, K6KR -Original Message- From: Dave G4AON [mailto:elecr...@astromag.co.uk] Sent: Saturday, December 27, 2008 2:26 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W

RE: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

--Original Message- From: Dave G4AON [mailto:elecr...@astromag.co.uk] Sent: Saturday, December 27, 2008 2:26 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW Dick, nice utility. I've noticed an error can occur if the K3 i

Re: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

Dick, nice utility. I've noticed an error can occur if the K3 is set to lowish power when you start the calibration run. I had power set to 5.6 Watts and the 5 Watt cal routine failed. Setting the power to 35 Watts allowed it all to run correctly. Apologies if this has already been noted. 73 and a

RE: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

Dick, K6KR -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of NZ0T Sent: Thursday, December 25, 2008 3:54 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW Well DUH! I

Re: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

I've got a duh of my own... I did enable TECH MD and looking at page 48 under transmitter gain in config I see no TXGN demonstrated; I see Tx DLY, Tx ESSB and Tx GATE. Doing the PWR SET and setting the output to say 5W and then holding tune, it does calibrate 5W for that specific band that I'm

Re: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

Well DUH! I forgot to enable CONFIG:TECH MD. Once done the calibration ran like a champ. NZ0T wrote: > > I'm getting an error message and the calibration fails. I am > communicating fine with the K3. The message is "Unexpected response > "d...@nqr@008AE" to "DS" State 41. The "AE" are diffe

Re: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

wayne burdick wrote: Dick just announced his latest revision of K3 Utility (see below), which will automatically perform all of the steps involved in K3 transmit gain calibration. I'm posting, too, just in case his subject line didn't your attention. This is a real labor-saver. It can safely

Re: [Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

I'm getting an error message and the calibration fails. I am communicating fine with the K3. The message is "Unexpected response "d...@nqr@008AE" to "DS" State 41. The "AE" are different characters than I can type here but the closest I can come to them. Any ideas? And Merry Christmas!! Bill

[Elecraft] K3: Automated Transmit Gain Calibration at 5 W, 50 W, and 1 mW

Dick just announced his latest revision of K3 Utility (see below), which will automatically perform all of the steps involved in K3 transmit gain calibration. I'm posting, too, just in case his subject line didn't your attention. This is a real labor-saver. It can safely be done at any time, e