Andy:
Thanks for the update!
73,
Barry, WD4ASW/1
> On Oct 7, 2021, at 8:07 AM, Andy Durbin wrote:
>
> "Could you note some of the ‘fixes’ that are not noted in the release notes?"
>
> Here is a more complete list:
>
> * An enabled antenna is not selectable with mode BYP
>
> * F;
Hi Andy,
No, not with the beta, that is untested at this point. I need to move
the new software into the KAT then test again... Thank you for asking!
73, and thanks,
Dave (NK7Z)
https://www.nk7z.net
ARRL Volunteer Examiner
ARRL Technical Specialist, RFI
ARRL Asst. Director, NW Division,
"If I use any sort of fast turn around transmit/receive cycle software,
like VARA, under Winlink, or ARQ type software modem, the tuner tries to
re-tune every time a most transmit cycles, even with a good SWR on the
antenna."
Are you saying that you see this with beta 2.04? If so, have you
Given we are talking about Beta software, I think I have located another
issue with the KAT500...
If I use any sort of fast turn around transmit/receive cycle software,
like VARA, under Winlink, or ARQ type software modem, the tuner tries to
re-tune every time a most transmit cycles, even
"Could you note some of the ‘fixes’ that are not noted in the release notes?"
Here is a more complete list:
* An enabled antenna is not selectable with mode BYP
* F; interrogation returns zero after CAT induced band change
* Unexpected behavior for FCCS and FCMD
* Fault code 01 when
-boun...@mailman.qth.net On
Behalf Of Mike Cox
Sent: Wednesday, October 6, 2021 13:20
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KAT500 beta 2.04
It looks like the utility is for 64 bit Windows only...
On 10/6/2021 11:27 AM, Andy Durbin wrote:
> https://elecraft.com/pages/kat500-fu
It looks like the utility is for 64 bit Windows only...
On 10/6/2021 11:27 AM, Andy Durbin wrote:
https://elecraft.com/pages/kat500-fully-automatic-tuner-firmware-and-utility
New KAT500 firmware and also a new Utility version. Quite a few issues fixed
that are not mentioned in the release
Subject: Re: [Elecraft] KAT500 beta 2.04
"Could you note some of the 'fixes' that are not noted in the release
notes?"
I don't have a complete summary in one place. I'll try to put one together
later. A few that come to mind are:
Does not fault when tuning with low power Less likely to
"Could you note some of the ‘fixes’ that are not noted in the release notes?"
I don't have a complete summary in one place. I'll try to put one together
later. A few that come to mind are:
Does not fault when tuning with low power
Less likely to end a full tune sequence with a poor match
Andy:
> On Oct 6, 2021, at 11:27 AM, Andy Durbin wrote:
>
> https://elecraft.com/pages/kat500-fully-automatic-tuner-firmware-and-utility
>
> New KAT500 firmware and also a new Utility version. Quite a few issues
> fixed that are not mentioned in the release notes.
Could you note some of
"Tried the new version of the Utility. 'Invalid handle' error when 'Copy New
Files from Elecraft' is clicked. Unzipped the new beta firmware into my beta
directory, and when I tried loading the beta firmware I got 'Cannot start a
busy state machine' error."
All my testing was done with
gt; Subject: RE: [Elecraft] KAT500 beta 2.04
>
> Hi Andy,
>
> Tried the new version of the Utility. 'Invalid handle' error when 'Copy
> New Files from Elecraft' is clicked.
>
> Unzipped the new beta firmware into my beta directory, and when I tried
> loading the beta firmware I
for now ...
- 73 and good DX de Mike, K6MKF, NCDXC Vice-President 2021-2022
> -Original Message-
> From: elecraft-boun...@mailman.qth.net boun...@mailman.qth.net> On Behalf Of Andy Durbin
> Sent: Wednesday, October 06, 2021 08:28
> To: elecraft@mailman.qth.net
> Subject:
https://elecraft.com/pages/kat500-fully-automatic-tuner-firmware-and-utility
New KAT500 firmware and also a new Utility version. Quite a few issues fixed
that are not mentioned in the release notes.
I'd like to thank Dick, K6KR, for his patience as we worked though my defect
reports and
14 matches
Mail list logo
