I ran a couple of these several years ago with EMC(1) without any big
issues. I did have to use a stand-alone setup program to configure its
ports but once that was done it looked like an ordinary 8255 just with a
strange port addy. Back then there was a German group writing Linux
drivers for th
Hello,
I would like to modify an existing AXIS translation.
Where is the file do i have to change?
Many thanks
J.J.
-
This SF.net email is sponsored by: Splunk Inc.
Still grepping through log files to find problems? Stop.
N
My friend was telling me how the HAAS he is looking at can run macros to
find hole center and edges etc. Can something like that be done in EMC?
I know you could load a G file to do that but a press of the button would be
faster.
Thanks
John
Hello,
the file ist xx_axis.po in src/po directory of the sources (etc.
CVS...), where xx stands for your language code, etc "de" for germany,
"ru" for russia..
If you have checked out a CVS version, re-run make from src, otherwise
run "msgfmt -o axis.mo xx_axis.po" and replace the file in
/us
Thanks for the help John,
the pin??-in-not works great!
The typo is located in my computer in
emc2/configs/stepper/standard_pinout.hal. Also, the user manual chapter
4.3.1 is infested with the same typos. There are several lines near the
bottom of the page with the parport number missing. I ha
Unfortunately, it is not possible to run gcode subroutines from MDI mode. I
hope to fix that in the future.
That would let you do things like:
O call
in the mdi window.
Ken
[EMAIL PROTECTED]
Mark Kenny Products Company, LLC
55 Main Street Voice: (888)ISO-SEVO (888)476-7386
Newtown, CT 06
On Fri, 2007-11-09 at 09:22 -0500, xtra209 wrote:
> Is there any way to link more than one axis limit pin to one parport pin
> and not fault the other axis while homing?
This is a known problem. I use ladder to interrupt the parport limit
signal if any axis is homing. It's a single rung.
Ray
John,
And the same typos are found in the integrator's manual chapter 13.3.1 too.
HTH,
Clint
--
Message: 5
Date: Thu, 08 Nov 2007 22:56:06 -0500
From: John Kasunich <[EMAIL PROTECTED]>
Subject: Re: [Emc-users] Limit switch polarity?
To: "Enhanced Machine Controller
On Fri, Nov 09, 2007 at 11:41:36AM -0600, Jeff Epler wrote:
> net probe parport.0.pin-26-in-invert motion.probe-input
Correction:
> net probe parport.0.pin-26-in-not motion.probe-input
Always refer to documentation and/or 'halcmd show' before typing pin and
parameter names into an e-mail
Paul Ritchie wrote:
> Anyone know if the 82C55 driver in EMC can be used with the following
> (or similar) low-cost card?
>
> http://www.measurementcomputing.com/cbicatalog/cbiproduct_new.asp?dept_id=224&pf_id=821&mscssid=5LA5N9DR9EDR8HQR46CQ7XPCSCD4DH75
>
> Seems like a good alternative to para
You configure a probe just like almost everything else in emc: add the
right lines to a .hal file. In this case, you will be writing a line to
connect a signal to the pin "motion.probe-input". For example, if the
probe input is on parport pin 26*, you could write
net probe parport.0.pin-26-in
> Subject: Re: [Emc-users] Low Cost Motion Contorl Card?
>
> Paul Ritchie wrote:
>> Anyone know if the 82C55 driver in EMC can be used with the following
>> (or similar) low-cost card?
>>
>> http://www.measurementcomputing.com/cbicatalog/cbiproduct_new.asp?dept_id=224&pf_id=821&mscssid=5LA5N9DR9ED
Peter C. Wallace wrote:
>
>
> Besides I dont think parallel port cards are going away any time soon, I just
> saw a just released PCI-express - Serial/parallel/localbus chip...
How much was that PCI-E card? I may have to get a system with
PCI-E and use a parallel card in it to explore the impl
On Fri, 9 Nov 2007, Jon Elson wrote:
> Date: Fri, 09 Nov 2007 20:36:30 -0600
> From: Jon Elson <[EMAIL PROTECTED]>
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] Low Cost Motion Contorl Card?
>
> Peter C. Wallace wrote:
On Fri, 9 Nov 2007, Peter C. Wallace wrote:
>> How much was that PCI-E card? I may have to get a system with
>> PCI-E and use a parallel card in it to explore the implications
>> of serializing the communications.
>>
>> Thanks for the news flash!
>>
>> Jon
>
>
> This was just the chip (MOSCHIP MC
Is there anyone out there that has a working set/direction parallel port
configuration for a puma robot? I'm in the middle of designing a puma style
robot. I wanted to stay cheap and simple, so any help I could get it getting
this to work would be great. I tried to make this modification in a pr
Peter C. Wallace wrote:
> On Fri, 9 Nov 2007, Jon Elson wrote:
>
>
>>Date: Fri, 09 Nov 2007 20:36:30 -0600
>>From: Jon Elson <[EMAIL PROTECTED]>
>>Reply-To: "Enhanced Machine Controller (EMC)"
>>
>>To: "Enhanced Machine Controller (EMC)"
>>Subject: Re: [Emc-users] Low Cost Motion Contorl Car
17 matches
Mail list logo
