For the specific purpose of measured tool lengths, use G43.1 I- K-
"dynamic tool compensation" instead of coordinate system offsets.
http://linuxcnc.org/docs/2.3/html/gcode_main.html#sub:G43,-G49:-Tool
In v2.4 the gcode will be incompatibly changed because tool length
offsets can apply to all axes
Thanks for the replies.
Based on your comments, I am backing away from these for the time being.
Your comments led me to realize this is beyond my focus at this time. While
I certainly could attack this project, family, travel and home renovations
are trumping my efforts at this time.
As an asid
On Sun, 2010-02-28 at 12:36 -0500, BRIAN GLACKIN wrote:
... snip
> If anyone is interested in chasing them, search Reading PA craigslist and
> Mitutoyo and they will pop up. This is the second relisting (that I am
> aware of) by the seller so its not like they are flying off the shelf.
>
> Brian
On 27 February 2010 23:33, Frank Tkalcevic wrote:
> Can this be done in Gcode? I can't see how to get the current machine
> position in gcode.
I found a clunky way to do it by using G92 X0 Z0 then reading the
offsets stored in #5211 and #5213.
This assumes you want the current relative (workin
Hi All:
I have a problem with my stepper driver board. The board is made by
Stepmaster. Board # SOP-1 ver. 1.2
I need steplen, stepspace, dirsetup, and dirhold.
Can't get steppers to be reliable faster than Max. Vol. .3
Anyone help?
Thanks:
Bill
-
On Sun, 2010-02-28 at 11:32 -0700, Cathrine Hribar wrote:
> Hi All:
> I have a problem with my stepper driver board. The board is made by
> Stepmaster. Board # SOP-1 ver. 1.2
>
> I need steplen, stepspace, dirsetup, and dirhold.
> Can't get steppers to be reliable faster than Max. Vol. .3
>
> A
- Original Message -
From: "BRIAN GLACKIN"
To: "Enhanced Machine Controller (EMC)"
Sent: Sunday, February 28, 2010 11:36 AM
Subject: Re: [Emc-users] Linear Scales
> Thanks for the replies.
>
> Based on your comments, I am backing away from these for the time being.
> Your comments led
Does anyone have a source for these?:
http://www.avagotech.com/docs/AV02-0188EN
Mouser wants to sell me 204 of these. Digikey says it's a non-stock
item.
One nice thing about these is the SPI like output.
--
Kirk Wallace
http://www.wallacecompany.com/machine_shop/
http://www.wallacecompany.com/E
www.avnet.com looks like they sell the AEAT-6010 and AEAT-6012 in single
unit quantities.
Lawrence
On Sun, Feb 28, 2010 at 12:14 PM, Kirk Wallace
wrote:
> Does anyone have a source for these?:
> http://www.avagotech.com/docs/AV02-0188EN
>
> Mouser wants to sell me 204 of these. Digikey says it's
On Sat, 2010-02-27 at 19:17 -0500, ad...@mmri.us wrote:
> CORRECTION: Ignore previous mail
>
> Any dwg to dxf converter for Linux available yet ?
> Qcad, graphite and Dia do not support dwg.
>
The only Linux program that I know of that opens dwg files is VariCAD
and only 2D, it will export a dxf.
On Sunday 28 February 2010, Cathrine Hribar wrote:
>Hi All:
>
>I have a problem with my stepper driver board. The board is made by
>Stepmaster. Board # SOP-1 ver. 1.2
>
>I need steplen, stepspace, dirsetup, and dirhold.
>
>Can't get steppers to be reliable faster than Max. Vol. .3
>
The first link
All,
Be cautious about fitting magnetic encoders to the back of NEMA34 or
larger step motors. The magnetic field in the area where the encoder is to
be installed is strong enough to screw up the encoder readings.
The effect shows up as noise on the position reading.
John (The hard way)
On Sun, 28 Feb 2010 16:23:48 -0500
Gene Heskett wrote:
> On Sunday 28 February 2010, Cathrine Hribar wrote:
>>Hi All:
>>
>>I have a problem with my stepper driver board. The board is made by
>>Stepmaster. Board # SOP-1 ver. 1.2
>>
>>I need steplen, stepspace, dirsetup, and dirhold.
>>
>>Can'
On Sun, 2010-02-28 at 14:48 -0700, John Harris wrote:
> All,
> Be cautious about fitting magnetic encoders to the back of NEMA34 or
> larger step motors. The magnetic field in the area where the encoder is to
> be installed is strong enough to screw up the encoder readings.
>
> The effec
On Sun, 28 Feb 2010 16:23:48 -0500, you wrote:
>I have 2 myself, abide by the rules and my machine can move 25 ipm with a
>27.5 volt supply.
>
>They are I believe the same allegro chip used on the xylotex boards, but
>xylotex puts heat sinks on them and recommends plenty of air flow for full
>
On Sunday 28 February 2010, Cathrine Hribar wrote:
>On Sun, 28 Feb 2010 16:23:48 -0500
>
> Gene Heskett wrote:
>> On Sunday 28 February 2010, Cathrine Hribar wrote:
>>>Hi All:
>>>
>>>I have a problem with my stepper driver board. The board is made by
>>>Stepmaster. Board # SOP-1 ver. 1.2
>>>
>>>
On Sunday 28 February 2010, Steve Blackmore wrote:
>On Sun, 28 Feb 2010 16:23:48 -0500, you wrote:
>>I have 2 myself, abide by the rules and my machine can move 25 ipm with a
>>27.5 volt supply.
>>
>>They are I believe the same allegro chip used on the xylotex boards, but
>>xylotex puts heat sinks
Hi
I run cylindrical grinder Okuma and i know that there will be problem to
run cylindrical grinder with EMC2.
Problem is that cylindrical grinder will use special and unique for
cylindrical grinders cycle code and EMC2 doesn't have that. I grind
ceramics with diamond wheel and material removal per
Hi
I try to load UBUNTU on computer that has USB type mouse. During
installation mouse did not work.
Is the problem between USB mouse and UBUNTU?
should i only use mouse that plug directly into mother board?
thanks
aram
---
On Sunday 28 February 2010, a...@conceptmachinery.com wrote:
>Hi
>I run cylindrical grinder Okuma and i know that there will be problem to
>run cylindrical grinder with EMC2.
>Problem is that cylindrical grinder will use special and unique for
>cylindrical grinders cycle code and EMC2 doesn't have
works!
Perhaps it will work for you as well.
Rudy
__ Information from ESET Smart Security, version of virus signature
database 4903 (20100228) __
The message was checked by ESET Smart Security.
http://www.eset.com
-
21 matches
Mail list logo