able to help
>
>
> regards
>
> giorgio
>
>
>
> Da: Jan Bos <rappyrip...@gmail.com>
> Inviato: mercoledì 3 maggio 2017 06.06
> A: Enhanced Machine Controller (EMC)
> Oggetto: Re: [Emc-users] touch screen calibration assistance please
>
&
Thanks everybody for hanging in there with me trying to figure this thing
out.
I ended up with calibration values as follows:
Option "Calibration""2025 27 125 1950" in the 99-calibration.conf
This gets my touch point within 1mm of where I actually touch the screen
with a stylus. I also
n figure it out from here maybe.
More tomorrow.
Jan
On Wed, May 3, 2017 at 3:56 AM, andy pugh <bodge...@gmail.com> wrote:
> On 2 May 2017 at 20:40, Jan Bos <rappyrip...@gmail.com> wrote:
>
> > Now I did what and how to get my beloved desktop back?
>
> does "sta
AM, Jan Bos <rappyrip...@gmail.com> wrote:
> Hello Andy,
>
> Thanks for your quick reply!
>
> OK, I got it installed finally and I can go through the calibration for
> the screen. For some reasons I have 2 eGalaxy Inc. Touch devices listed
> according my Xinput outp
, andy pugh <bodge...@gmail.com> wrote:
> On 2 May 2017 at 18:36, Jan Bos <rappyrip...@gmail.com> wrote:
>
> > I tried to install 'xinput-calibrator' to calibrate the touchscreen but
> > when I enter in my terminal window:
> >
> > 'sudo apt-get install xinpu
Hello everybody,
I have a USB touchscreen that is almost working OK except the X axis is
inverted. Pressing on the right hand side of the screen makes whatever is
on the left pop-up. Sliding my finger from right to left makes the cursor
move from left to right. Up and down is OK.
My system is a
Hello Andy,
Thanks again and I will see if I got more issues to help you out
Jan
On Tue, Apr 4, 2017 at 8:42 AM, andy pugh <bodge...@gmail.com> wrote:
> On 4 April 2017 at 01:33, Jan Bos <rappyrip...@gmail.com> wrote:
> > Thanks, surprises me each time how so
in the towel.
Jan.
Jan
On Tue, Apr 4, 2017 at 4:00 AM, andy pugh <bodge...@gmail.com> wrote:
> On 3 April 2017 at 20:24, Jan Bos <rappyrip...@gmail.com> wrote:
> > For whatever reason, the output 'near.0.out' never goes true. I changed
> the
> > scale to 1.5 and
Hello everybody,
I am having a problem with my spindle at speed signal.
I have the encoder working and the spindle runs at 6000 rpm and I get the
values below which seem correct since these are RPS and not RPM.
Here is what I am using in my HAL:
net spindle-vel-cmd-rps=> near.0.in1
net
, 2016 at 12:00 PM, Jan Bos <rappyrip...@gmail.com> wrote:
> Thanks Peter, will free up these and try again. Will let you know if I
> have more issues getting this to work.
>
> G21
>
> On Wed, Dec 28, 2016 at 11:48 AM, Peter C. Wallace <p...@mesanet.com>
> wrote:
Thanks Peter, will free up these and try again. Will let you know if I have
more issues getting this to work.
G21
On Wed, Dec 28, 2016 at 11:48 AM, Peter C. Wallace <p...@mesanet.com> wrote:
> On Wed, 28 Dec 2016, Jan Bos wrote:
>
> > Date: Wed, 28 Dec 2016 10:49:33 +0800
I am trying to read an analog input from a digital I/O pin on my 7I76.
According to the manual this is possible albeit in 8 bit mode only which is
fine for me. I have a spindle drive that provides a 0 5V output for spindle
load and I want to read this and show this in my Glade sidepanel.
The
Hello Marius,
Thanks a lot for your detailed explanation and your comp file. I printed it
and will go through it to see what I need to do to adapt it.
I see you made quite some changes to it compared to the original carousel
component, am I missing the shortcomings of the original carousel
all...@wallacecompany.com>
wrote:
> On 11/03/2016 06:23 PM, Jan Bos wrote:
> ...
> > Do I need to add a 'home' sensor or a 'pocket 1' sensor?
> >
> > I am not quite clear on how this is supposed to work, could anybody shine
> > some light on how the Carousel com
Hello everybody,
I am working on an ATC for my mill and intend to use the carousel
component. My ATC has only one sensor that detects the pockets, it is a
Geneva style ATC and the sensor is on the drive wheel and senses each
rotation i.e. each step the wheel makes. There is no sensor to tell the
15 matches
Mail list logo
