I don't know if anyone else has this problem.
If I switch to cw from ssb, or the other way, the ptt or break in do not
work.
If I stop SDR and restart all comes back ok. As soon as I switch between
cw and ssb
again it quits. It is very consistent on 160-40m, not so much above 30m.
Vox works no mat
This is likely all related;
As of svn 1738 break-in on cw ceases to function unless the VAC button
is selected and then de-selected, or the console is powered off/on. The
radio works for a short period and then spontaneously quits transmitting
(no t/r). Eric's been working on this over the last sev
I am running SVN 1738 and see the same problem. Also I tried to use it on CW
and no go at all. This is with SDR-1000. v1.10.3 is fine.
Joe K1RQG
In a message dated 11/10/2007 12:54:28 A.M. Eastern Standard Time,
[EMAIL PROTECTED] writes:
I don't know if anyone else has this problem.
If
did you check Setup>General>Options and see if All Mode Mic PTT is enabled.
Mine doesn't want to 'stay' enabled.
I have to check this frequently.
On 11/10/2007 12:04:43 AM, [EMAIL PROTECTED] wrote:
> I am running SVN 1738 and see the same problem. Also I tried to use it on
> CW
> and no go at all
Yes, it stays checked.
Nothing anywhere in the setup changes.
I just set it on a frequency and toggle between
lsb and cwl, then break in or ptt don't work anymore.
FireBrick wrote:
> did you check Setup>General>Options and see if All Mode Mic PTT is enabled.
> Mine doesn't want to 'stay' enabled.
I can't duplicate this.
I've tried a number of times.
Although I read of someone else with a similar problem
how does your ptt get it's commands?
Is it a 'virtual port'?
Or is it a hardwire ptt button or footswitch?
What version firmware and driver?
Does your radio communicate with a logging/cont
--Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of FireBrick
Sent: Saturday, November 10, 2007 10:17 AM
To: FlexRadio List
Subject: Re: [Flexradio] PTT Broken
I can't duplicate this.
I've tried a number of times.
Although I read of someone else with a
W9DVM
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Richard Stouffer
Sent: Saturday, November 10, 2007 11:43 AM
To: 'FireBrick'; 'FlexRadio List'
Subject: Re: [Flexradio] PTT Broken
I had the problem on my 5000 and then thoug
I'm using the Flex 1000
The ptt and keyer are hard wired to the radio.
I'm not using com ports for keying, but
I have no problem with the com ports, the logging
programs track no problem.
I imagine this is peculiar to the 1000.
I haven't tried yet to see which version of svn below the current is ok
_
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
Sent: Saturday, November 10, 2007 12:08 PM
To: Phil LaMarche
Subject: Re: [Flexradio] PTT Broken
As you admit to having/using an EQ PLUS (sort of like "Hello, my name is
Bob, and I'm an alcoholic"), could it
List
Subject: Re: [Flexradio] PTT Broken
I'm using the Flex 1000
The ptt and keyer are hard wired to the radio.
I'm not using com ports for keying, but
I have no problem with the com ports, the logging
programs track no problem.
I imagine this is peculiar to the 1000.
I haven't tried y
727-944-3226
> FAX 727-937-8834
> NASFT 30210
> W9DVM
>
>
>
> -Original Message-
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] On Behalf Of Richard Stouffer
> Sent: Saturday, November 10, 2007 11:43 AM
> To: 'FireBrick'; 'FlexRadio
> List'
gt;> W9DVM
>>
>>
>>
>> -Original Message-
>> From: [EMAIL PROTECTED]
>> [mailto:[EMAIL PROTECTED] On Behalf Of Richard Stouffer
>> Sent: Saturday, November 10, 2007 11:43 AM
>> To: 'FireBrick'; 'FlexRadio
>> List'
>
Due to the fact that it is not present in earlier SVN versions
it is probably a bug, and I have submitted it as such.
By the way my keyer (Microham CW Keyer) is plugged
directly into the Flex key jack, and I do not have iambic mode enabled.
Kirb Nesbitt wrote:
> This is likely all related;
> As o
I'm having a similar problem just using the internal CWX keyer. Works once
after starting or after
VAC On/Off then stops. Makes for short QSO's... Worked fine this morning on
40 - I'm pretty sure
that was before updating to 1738. I'll just listen for a while!
Mark
W8XR
Due to the fact
Upon further investigation I have found that any change (ie: change
power, push another button) on the console
will disable break in & ptt when in cw mode.
Also the power output is always full power no mater what the console is
set at in cw, which sucks if you run an amp.
Stop the console and res
itt
Sent: Saturday, November 10, 2007 10:29 AM
To: flexradio@flex-radio.biz
Subject: [Flexradio] PTT Broken
This is likely all related;
As of svn 1738 break-in on cw ceases to function unless the VAC button is
selected and then de-selected, or the console is powered off/on. The radio
works for a s
, so I can't verify it. I
> plan to sell it soon.
>
> 73,
>
> Steve N6VL
>
> -Original Message-
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] On Behalf Of Kirb Nesbitt
> Sent: Saturday, November 10, 2007 10:29 AM
> To: flexradio@flex-radio.biz
>
I had same problem and went back 1 version and problem went away.
[EMAIL PROTECTED]
http://www.qsl.net/wd1v
On Nov 10, 2007 1:04 AM, <[EMAIL PROTECTED]> wrote:
>
> I am running SVN 1738 and see the same problem. Also I tried to use it on CW
> and no go at all. This is with SDR-1000. v1.10.3 is
I am also having trouble with PTT, but exclusively on phone.
This is with my shiny new Heil Microphone purchased from Flex. I have
never gotten SSB (or AM) to work with my Flex 5000 -- the microphone was
purchased to get it going.
At first I thought the Mic might have a problem.
So, I took th
Thanks to one and all who had me check out the cable. It was indeed the
cable.
Removing the covers on the rig is covered in a knowledge base article I
was pointed at. Once done, I had to get one of those "star" type
screwdrivers and after that, a cautious remove of the fan on the bottom
reve
21 matches
Mail list logo