Riwan, Jakarta, Indonesia
Mateusz Gierblinski wrote:
Hi misc@
I'm just wondering. Where are you OpenBSD users from?
I'm from Belgium, anyone else?
Take care
I had the same problem year ago.
STP or RSTP looping can cause the OpenBSD hardware to freeze.
I could not figure out why suddenly my firewall is not working.
Then I noticed that the switch led is blinking crazily.
I remove the cable, and my firewall was normal again.
Brgds,
Riwan
Christian
Hi,
I have a BGP and OSPF network. Configuration:
BSD A - ospf - net_1 - ospf - cisco1 - ospf - BSD B - ospf - cisco2 -
ospf - net_2 - bgp - BSD C
In B, there are route that use net_1 which metric is bigger than net_2.
net_1 and net_2 are different provider.
Can anyone help me to figure out
Hai,
Sorry to bother you again, however doing
ntpd -s
I got
# tail -f /var/log/daemon
Jul 21 15:04:29 pceng4 ntpd[8943]: listening on 192.168.1.200
Jul 21 15:04:29 pceng4 ntpd[8943]: listening on fe80:1::20d:b9ff:fe14:ef48
Jul 21 15:04:29 pceng4 ntpd[8943]: listening on 192.168.10.200
Jul 21
Hai all,
I have problem on clock with Alic3 board from Pc Engines on OpenBSD 4.3
dmesg-
OpenBSD 4.3 (GENERIC) #698: Wed Mar 12 11:07:05 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS (AuthenticAMD
586-class) 499 MHz
cpu0:
I want my OpenBSD 4.3 to get clock from my serial GPS device.
The device is working
# cu -l /dev/cua00 -s 4800
Connected
$GPRMC,113516.000,A,0608.4965,S,10651.2976,E,0.07,229.06,090708,,,A*75
$GPRMC,113517.000,A,0608.4964,S,10651.2975,E,0.04,193.07,090708,,,A*76
Thanks you to point it out. Minor mistake big different.
It working.
Best regards,
Riwan
Stuart Henderson wrote:
On 2008-07-09, riwanlky [EMAIL PROTECTED] wrote:
server nmea0
it's not a server, it's a sensor.
hai,
i have same problem. however reading the mailing list i found the solution.
use pf, ddclient (for dhcp ip listing to the internet with zoneedit) is the
answer.
route add default adsl
route add default dhcp ip -mpath
then in the pf.conf
pass in on adsl inet proto icmp keep state
pass in on
hai,
i have same problem. however reading the mailing list i found the solution.
use pf, ddclient (for dhcp ip listing to the internet with zoneedit) is the
answer.
route add default adsl
route add default dhcp ip -mpath
then in the pf.conf
pass in on adsl inet proto icmp keep state
pass in
Hi,
route add -mpath use with pf.conf could do load balancing from internal
to public network.
my question is how to setup pf.conf or kernel, so that from the public
network can access the public interfaces.
it seem to me that the first default route/ interface will send out all
traffic
.
Sorry for the noise.
Best regards,
Riwan
At 03:21 PM 6/9/2007 +0700, riwanlky wrote:
HI All,
I am having problem with network card on Intel Motherboard on OpenBSD 4.1.
However the same motherboard and network card do not have problem wiht
OpenBSD 4.0
When loading the card:
em0 at pci3 dev 0
.
Sorry for the noise.
Best regards,
Riwan
At 04:35 PM 6/4/2007 +0700, riwanlky wrote:
Hi All,
I have a problem with new installation on my new Intel board server.
However installing the OBSD 4.0 on the same server work. The OBSD 4.1
panic on uhci0, I think.
It said kernel panic and halt.
Dmesg
Hi All,
I have the following configuration:
* three internet connection with different provider
* OpenBSD 4.1 as the firewall
* One DMZ zone
* One internal zone.
I was able to use loadbalancing to connect internal to the
internet using two connection.
The problem I have is that I will not be
HI All,
I am having problem with network card on Intel Motherboard on OpenBSD 4.1.
However the same motherboard and network card do not have problem wiht
OpenBSD 4.0
When loading the card:
em0 at pci3 dev 0 function 0 Intel PRO/1000MT (82573e) rev
0x03uvm_fault(0xd0691180,
0x1f000, 0, 1) -
Hi All,
I have a problem with new installation on my new Intel board server.
However installing the OBSD 4.0 on the same server work. The OBSD 4.1
panic on uhci0, I think.
It said kernel panic and halt.
Dmesg from the same server with OBSD 4.0
OpenBSD 4.0 (GENERIC) #1107: Sat Sep 16 19:15:58
Hi All,
Need help.
128 Kb router link to the internet.
OpenBSD connect to the router on ste2. (100Mb link)
OpenBSD 100Mb internal link ste0.
Running Squid on the OpenBSD. Listening on port 3128
Running Web server on the OpenBSD.
Running named on the OpenBSD.
It seem that the internal users
Thanks all,
I had tested 4.0, and I don't have any problem.
Thanks and best regards,
Riwan
At 11:27 AM 3/22/2007 +0800, Lars Hansson wrote:
[EMAIL PROTECTED] wrote:
Hai All,
I have two OpenBSD 3.9 box, both running OSPFD default on OBSD 3.9.
I add static route on OBSD1 and found that the
Dear All,
I don't know if this is the forum to ask such question:
How do I install php4 and php5 on the same OSBD 4.0?
Somehow I need both for some software that I am running.
I can do that with python2.4 and python2.3
Thanks and best regards,
Riwan
Hi All,
I am sorry if I didn't get the answer searching the mailing list
and man route.
I have two ISP, and wondering how should I setup the default
route to the ISP.
I am wondering if I have two gateway going to the same route can I use metric?
route add 0.0.0.0/0 192.168.6.1 10
route add
Hi All,
I had a problem, I do as been told by the OpenBSD cover on installation
of the drive.
80m for /
300m for swap
80m for /tmp
80m for /var
2g for /usr
all the other for /home
however it seem that my /var allocated more than 70%, I will like to
enlarge it. I use all my partition in the
will not
support it, the only can support static route from us and from
them to us.
Best regards and thanks.
Riwan
At 03:24 PM 3/26/2007 +0100, Stuart Henderson wrote:
On 2007/03/26 20:33, riwanlky wrote:
I have two ISP, and wondering how should I setup the default
route to the ISP.
you need to give a lot
Hi All,
I want all my windows client behind OpenBSD 3.9 firewall to query
dns from the firewall. In the OpenBSD 3.9 I run named. This is
my named.conf
acl clients {
localnets;
::1;
};
options {
version ; // remove this to allow version queries
listen-on
Dear All,
I have a problem with Intel D102GGC2 board and DLink 580TX card, where
it did not detect the DLink 4 ports 10/100 ethernet on OpenBSD 4.0.
OpenBSD 4.0 only detect two ports ste2 and ste3.
I am wondering if it is the problem with detecting IRQ, It stated IRQ 11. Where
on Windows the
hi all,
i just purchase a new asus barebone pc pundit-p1 and want to install openbsd.
i had to disable ieee 1394 and usb controller.
i run xdm, and it only show blank screen.
attached is the dmesg and the Xorg.0.log
can anyone give me information on how to resolve this.
thanks and best
It's fine with me. I had ordered 3.8, 3.9 and just order 4.0
At 01:22 PM 9/21/2006 -0600, Theo de Raadt wrote:
2006/9/21, L. V. Lammert [EMAIL PROTECTED]:
Nope, totals are right at the top of the page.
+ Shipping.
When am I told, how much shipping will cost? At least not before I
submit
After looking for a while for multimedia firefox plugins, I am glad to
hear that there is flash plugins (well, after trying to compile, without
any luck to
get vlc plugin for mozilla from ports) from redhat emulation.
However I tried to compile the opera-plugins, however I could not
get
, Sep 19, 2006 at 05:05:50PM +0700, riwanlky wrote:
After looking for a while for multimedia firefox plugins, I am glad to
hear that there is flash plugins (well, after trying to compile, without
any luck to
get vlc plugin for mozilla from ports) from redhat emulation.
However I tried
Got it compile, opera-flashplugins. Sorry for the noise.
It seem that I could connect to ~jolan/ today.
the opera-flashplugin is working today. =))
Thanks and best regards,
Riwan
At 09:55 PM 9/19/2006 +0700, riwanlky wrote:
Yes, it is in the FAQ 13
One candidate is the Opera web browser
Had anyone try to make mozilla?
Any success. I tried without any success.
Brgds,
Riwan
At 07:08 AM 8/31/2006 +0300, Antti Harri wrote:
On Wed, 30 Aug 2006, stan wrote:
Am I overlooking something? I can't seem to find a firefox
port in the ports tree.
[EMAIL PROTECTED]:/usr/ports$ make
,clmilter
Xrxmilter, S=local:/var/spool/milter-regex/sock, T=S:30s;R:2m
Xclmilter, S=local:/var/run/clamav/clmilter.sock, F=, T=S:4m;R:4
Now both are working fine.
Best regards,
Riwan
At 02:15 PM 8/11/2006 +1100, Zoong PHAM wrote:
On Friday, 11 August 2006 at 8:00:38 +0700, riwanlky wrote
hi all,
if it is possible to have more than one milter while using sendmail?
i have the following configuration in my sendmail.cf
# Input mail filters
O InputMailFilters=clmilter
Xclmilter, S=local:/var/run/clamav/clmilter.sock, F=, T=S:4m;R:4
O InputMailFilters=rxmilter
Xrxmilter,
Hi all,
I don't know if it is the right place to write about this problem.
I am running OpenBSD 3.9, however it seem to me that my OpenBSD
box always send a DNS query for:
- email sending (from internal and external) I had tried to add in my
resolv.conf to use nameserver localhost. So that
is to install via FTP (with pcibios disabled)
or use amd64 version. That, AFAIK, works fine.
More details at
http://www.armorlogic.com/openbsd_information_server_compatibility_list.html?action=detailid=x336
On 8/1/06, riwanlky [EMAIL PROTECTED] wrote:
Hai All,
I am trying to install OpenBSD 3.9 GENERIC
Thanks all, use config to modify the bsd and it work.
Brgds,
Riwan
At 10:27 AM 8/7/2006 +0100, Stuart Henderson wrote:
On 2006/08/07 16:05, riwanlky wrote:
Thanks, I tried to installed it using FTP, install completed. However
when I
reboot, it still try to use pcibios0. How do I disable
hi all,
i don't have any experience with how to use source or other
*nix tar.gz for openbsd. i need to have firefox 1.5.0.6. do anyone
know how do i get the firefox in my openbsd 3.9
thanks, and best regards,
riwan
Hi Polkan,
I myself is new in spamd. Just configure it few days ago. Up and runing fine.
So pardon me if it is not the answer you are looking for.
if you pf.conf you should have:
table spamd persist
table spamd-white persist
rdr pass on $ext_if proto tcp from spamd to port smtp \
-
Hi All,
I just configure my first spamd -g, I have a collegue in Korea who is sending
me a message, however it did not get through. I tried to whitelist it, however
it still did not get through.
This is the spamdb
WHITE|61.78.36.103|||1152841491|1152841518|1155951918|1|0
Hi All,
I am trying to run TWiki on my OBSD 3.9 box. Installed using pkg_add
TWiiki-20040903p0.tgz
Include the following in my httpd.conf:
ScriptAlias /twiki/bin/ /var/www/cgi-bin/twiki/
Alias /twiki/ /var/www/htdocs/twiki/
Directory /var/www/cgi-bin/twiki
Options +ExecCGI
Sorry,
I just go to rarlab and get the unrarsrc, put it in the distfiles.
Everything is working now. Clamav up and running.
Thanks,
Riwan
Date: Fri, 16 Jun 2006 08:22:52 +0700
To: Michael Erdely [EMAIL PROTECTED], sonjaya [EMAIL PROTECTED]
From: riwanlky [EMAIL PROTECTED]
Subject: Re: error
Hi guys,
I am trying to install Clamav on 3.9. Previously I used Clamav on 3.8 and
without
need to make install the unarj.
Manage to make install unarj. However Clamav require unrar and I got this
error.
# make install
=== Checking files for unrar-3.54p0
unrarsrc-3.5.4.tar.gz doesn't seem
Hi Guys,
I am going to install IDS for my firewall. According to this message
snort have problem, is there any alternative IDS? Is there any IPS?
Thanks,
Riwan
At 01:07 AM 6/13/2006 -0600, Bob Beck wrote:
Luckily, spamd greylisting saved the day. If it wasn't for BASE/snort
reporting of
Hai Julian,
I got the username and password. What is the username and password.
Best regards,
Riwan
At 12:49 AM 6/7/2006 -0400, Julian Bolivar wrote:
Hi everybody, I installed a Video Streaming server using OpenBSD 3.9 and
VideoLAN, I invite to all to visit my test page at
Hai,
Is there a documentation on installing OpenBSD 3.9 on USB flash drive?
With X Windows and Firefox latest version.
Should 128 MB be enough?
Thanks in advance,
Riwan
:
DDCLIENT works well for me on 3.7
riwanlky wrote:
Hi,
I will like to know if OpenBSD have the capability to update my dynamic
ip to www.dyndns.org.
I am currently running myDYNIPPRO on Windows to update my dynamic ip. I
want to
move to OpenBSD. I had currently running sendmail, popa3d, mrtg
Hi,
I will like to know if OpenBSD have the capability to update my dynamic ip
to www.dyndns.org.
I am currently running myDYNIPPRO on Windows to update my dynamic ip. I want to
move to OpenBSD. I had currently running sendmail, popa3d, mrtg, mySQL on the
machine.
Thanks and best regards,
Hi,
I am going to use sendmail and popa3d in release 3.8 for multiple domain.
I had setup and run mcojaya.com to run on rel 3.8. I will like to add
more domains:
mcojaya.com, abc.com, xyz.com, etc.
If I could do that, then how do i setup the users for those abc.com, xyz.com
Do I need other
hi,
I am trying to install pfstat in my OpenBSD 3.8 box, I am new in Unix-like OS,
I need to know how to compile the pfstat.
Many thanks in advance.
47 matches
Mail list logo