Hello,
I am trying to get Mandrake 8.0 up and running on a brand new Dell
Lattitude C800 Laptop, but I am seeing some really nasty video behavior.
It acts like it doesn't want to use the right-most 1/3 of the screen. The
video card is an ATI M4, with 32 MB RAM.
Has anyone else seen this type
I recently installed Mandrake 6.1 and I can't seem to X to run properly.
I am using am IBM PC300GL (Model 6272) this uses an integrated
Cirrus Logic 5446 Video Controller with 2Mb Mem. I am using an IBM
G54 monitor (but I don't believe this is the problem). When I Start X it
loads OK but the
On Wed, 22 Sep 1999, you wrote:
John,
I just went through the RH 5.2 book and haven't yet found any command that will
format the
HD for Linux. Who out there can point me in the correct direction command wise?
It should do that on install. However, the command is
mke2fs /dev/hdxx where xx
On Tue, 21 Sep 1999, Bill Crouch wrote:
John Aldrich wrote:
On Mon, 20 Sep 1999, you wrote:
Ok John, I finally figured out the "#" is the "REM" equivilant of DOS. My
problem is that when I went to do the "mount -w -o remount /dev/hda1/" I get
a message that the /root wasn't
On Mon, 20 Sep 1999, you wrote:
Ok John, I finally figured out the "#" is the "REM" equivilant of DOS. My
problem is that when I went to do the "mount -w -o remount /dev/hda1/" I get
a message that the /root wasn't mounted or "bad option" and the file is still a
read only. Now I am
John Aldrich wrote:
On Mon, 20 Sep 1999, you wrote:
Ok John, I finally figured out the "#" is the "REM" equivilant of DOS. My
problem is that when I went to do the "mount -w -o remount /dev/hda1/" I get
a message that the /root wasn't mounted or "bad option" and the file is still a
Bill Crouch wrote:
Steve Philp wrote:
Bill Crouch wrote:
Installing Mandrake (Venus) 6.0 everything appears to go well although
but I think my old Trident 1meg video card should display at 16 bit
level 640x480. Anyway, on initial boot after install load I get this:
INIT:
Bill Crouch wrote:
Installing Mandrake (Venus) 6.0 everything appears to go well although
but I think my old Trident 1meg video card should display at 16 bit
level 640x480. Anyway, on initial boot after install load I get this:
INIT: Entering run level 5
INIT: can't execute "/etc/rc.d/rc"
On Mon, 20 Sep 1999, you wrote:
I have the same problem, everything was working fine until I upgraded to a
new Epox m/b with a AMD K6-2 450 cpu. Those were the only changes I made
and I get the same errors. Reinstalled RH 5.2 and it runs fine, I think
the error is caused bu Xwindows.
I'm so
Installing Mandrake (Venus) 6.0 everything appears to go well although
but I think my old Trident 1meg video card should display at 16 bit
level 640x480. Anyway, on initial boot after install load I get this:
INIT: Entering run level 5
INIT: can't execute "/etc/rc.d/rc"
INIT: Id "1" respawning
Bill Crouch wrote:
Installing Mandrake (Venus) 6.0 everything appears to go well although
but I think my old Trident 1meg video card should display at 16 bit
level 640x480. Anyway, on initial boot after install load I get this:
INIT: Entering run level 5
INIT: can't execute
, and
then it crashes, with that error message.
neil
- Original Message -
From: Axalon Bloodstone [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Friday, August 27, 1999 6:15 AM
Subject: Re: [newbie] Video problems
On Fri, 27 Aug 1999, JK wrote:
I am running a number nine I128 with four
I am running a number nine I128 with four megs of ram. my monitors hsync is
30-95 and vsync is 47-150
res is 1600x1200 max
When I was running RH 6.0 it could handle 1280x1024 at 24 bpp now I am trying
to set my monitor to the same res and depth, but it will only hit max of
1280x1024 at 8 bpp
13 matches
Mail list logo
