Re: [weewx-user] Re: weewx stop working

Might be time for you to start a new thread specifically for your forecast problems, I think this one is getting a bit long and you now have a new issue. You might like to start off by stopping WeeWX, confirming debug = 1 in weewx.conf, deleting the forecast database forecast.sdb and then rest

Re: [weewx-user] Re: weewx stop working

I have manage to make all works except forecast. WU api doesn't work anymore so I tried OWM, but insted of OWM I get No forecast data for WU And I have setup API key and this is what I have in log Jun 18 09:32:49 povej weewx[32266]: forecast: MainThread: OWM: last forecast issued 2019-06-18 08:5

Re: [weewx-user] Re: weewx stop working

thank you. Yes I remove sofaskin from those, that was just for testing. -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscr...@googlegroups.com. T

Re: [weewx-user] Re: weewx stop working

That is good news. As a little background, WeeWX 3.9.0 saw the smartphone and mobile pages pulled out of the Standard skin into their own skins named Smartphone and Mobile. These skins were not necessarily enabled for all users. You can enable them (and Standard too if it is not enabled), but

Re: [weewx-user] Re: weewx stop working

yes that's it. Thank you, now all works. Just one question. All those skins for, mobile, smartphone, etc. can be all enabled? Dne ponedeljek, 17. junij 2019 21.58.37 UTC+2 je oseba vince napisala: > > On Monday, June 17, 2019 at 12:48:28 PM UTC-7, Damjan Hajsek wrote: >> >> In version 3.8.0 was

Re: [weewx-user] Re: weewx stop working

On Monday, June 17, 2019 at 12:48:28 PM UTC-7, Damjan Hajsek wrote: > > In version 3.8.0 was only one settings for skin now there are 4. > I tried all and always the same error, no matter where I use sofaskin. > Now I have disabled all and also tried all now only this is enabled and > doesn't work

Re: [weewx-user] Re: weewx stop working

OK, a few points. You have set each report under [StdReport] to use sofaskin, confusing but provided only one is enabled it should work. However, at the moment you have enable = false for all three, so none of them will generate. Finally, you have only shown us less than two minutes of your log

Re: [weewx-user] Re: weewx stop working

error below is from wrong database, I tried to use old database from 3.8.0 but it looks like 3.9.1 have some changes in database. So I switch to original database and error is gone and all what I have in log is this, but page doesn't update. Jun 17 09:06:50 povej weewx[2661]: interceptor: Server

Re: [weewx-user] Re: weewx stop working

I have copied sofaskin into folder /etc/weewx/skins/sofaskin end enable it in weewx.conf # This section specifies what reports, using which skins, to generate. [StdReport] # Where the skins reside, relative to WEEWX_ROOT SKIN_ROOT = /etc/weewx/skins # Where the generated

Re: [weewx-user] Re: weewx stop working

I have copied sofaskin into folder /etc/weewx/skins/sofaskin end enable it in weewx.conf # This section specifies what reports, using which skins, to generate. [StdReport] # Where the skins reside, relative to WEEWX_ROOT SKIN_ROOT = /etc/weewx/skins # Where the generated

Re: [weewx-user] Re: weewx stop working

You say ‘whatever I do’ - exactly what have have you tried? Have you restarted WeeWX? What does the log show when debug = 1? Gary -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, s

Re: [weewx-user] Re: weewx stop working

One more thing. In latest weewx.conf it is changed about skin. I use sofaskin and whatever I do weewx doesn't want to use that skin. I have change this line but weewx doesn't change skin. [[StandardReport]] # This is the old "Standard" skin. By default, it is not enabled. #skin

Re: [weewx-user] Re: weewx stop working

thank you. I see data now it works. Dne nedelja, 16. junij 2019 14.21.58 UTC+2 je oseba mwall napisala: > > On Sunday, June 16, 2019 at 4:53:31 AM UTC-4, Damjan Hajsek wrote: >> >> I will try to find help with creator of driver. I see they had the same >> problems before >> > > the problem is no

Re: [weewx-user] Re: weewx stop working

On Sunday, June 16, 2019 at 4:53:31 AM UTC-4, Damjan Hajsek wrote: > > I will try to find help with creator of driver. I see they had the same > problems before > the problem is not the interceptor, it is your configuration. you are listening on port 9900, but your station is not sending to tha

Re: [weewx-user] Re: weewx stop working

I will try to find help with creator of driver. I see they had the same problems before. Dne nedelja, 16. junij 2019 10.47.32 UTC+2 je oseba Andrew Milner napisala: > > HOORAY - now we have real progress and debug messages at last!! > > However it now appears your interceptor driver is not receiv

Re: [weewx-user] Re: weewx stop working

HOORAY - now we have real progress and debug messages at last!! However it now appears your interceptor driver is not receiving any data at all. I cannot help here - you need an interceptor user but there does appear to be a lot of debug/checking information back in the wiki to try and identify

Re: [weewx-user] Re: weewx stop working

Thank you. Finally, I thought I was insane, trying everything. I think some update must happend on april 4th when weewx stops to work. Now I have a log and this is all what I have for weewx. Jun 16 00:14:01 povej weewx: Starting weewx: [ V redu ] Jun 16 00:14:01 povej systemd: Started SYSV: sta

Re: [weewx-user] Re: weewx stop working

FYI, on all RH/Fedora (including CantOS) there are multiple consoles, which can be accessed by pressing CTRL-ALT 1 thru =. IIRC the debug messages go to console 12, the last one behind CRTL-ALT =, but having them in a file is preferred in my book. So, good job! =D Regards, \Leon -- Leon Shaner

Re: [weewx-user] Re: weewx stop working

On Saturday, June 15, 2019 at 8:09:28 AM UTC-7, gjr80 wrote: > > Thanks, so if I am reading the centos7.6 /etc/rsyslog.conf correctly only > info and above go to /var/log/messages. There is nothing covering debug > at all so I expect that is why debug is (effectively) discarded. We could > send

Re: [weewx-user] Re: weewx stop working

Thanks, so if I am reading the centos7.6 /etc/rsyslog.conf correctly only info and above go to /var/log/messages. There is nothing covering debug at all so I expect that is why debug is (effectively) discarded. We could send them to another file but that will make debugging difficult so let's ju

Re: [weewx-user] Re: weewx stop working

Gary, good sleuthing. Could it be that the debug messages simply go to a different file, such as /var/log/debug? Check to see where the debug logs are pointed in /etc/rsyslog.conf. Also, see here: https://www.the-art-of-web.com/system/rsyslog-config/ Regards, \Leon -- Leon Shaner :: Dearborn,

Re: [weewx-user] Re: weewx stop working

I guess the question is where to from here given that it appears you cannot get any debug output when running under centos7.6. I think we can assume that your system is running properly (debug issue aside) with the simulator driver. Troubleshooting the interceptor driver is going to be difficult

Re: [weewx-user] Re: weewx stop working

Well installing centos 7.6 on a VM was interesting. WeeWX 3.9.1 was installed from .rpm. It seems that when run under centos7.6 WeeWX (and python) any attempts to log at the debug level are discarded or otherwise lost. With debug=1: [root@VBCentosMaster ~]# cat /etc/weewx/weewx.conf|more # WEEW

Re: [weewx-user] Re: weewx stop working

Thank you. I use shorewall on my server and I have locked it on my home IP where weather station is. also fail2ban have my home IP whitelisted Dne petek, 14. junij 2019 18.52.23 UTC+2 je oseba Leon Shaner napisala: > > Damjan, > A long time ago you mentioned that your troubles all started when y

Re: [weewx-user] Re: weewx stop working

Damjan, A long time ago you mentioned that your troubles all started when you updated some OS pkgs. Have you seen this thread? Since you are using interceptor, which must accept connections from remote, it could be relevant: https://www.centos.org/forums/viewtopic.php?t=69009 To rule it out, p

Re: [weewx-user] Re: weewx stop working

Ok I did logs again I hope this time better. Dne petek, 14. junij 2019 14.44.03 UTC+2 je oseba Andrew Milner napisala: > > Not really, no > > The first part appears to show normal running with archive records every > minute - but no log for the startup process > > The second part, manual running

Re: [weewx-user] Re: weewx stop working

If you look back through this thread this is exactly where we were with the previous install - WeeWX running but with no indication in the startup log as to how debug was set, no turning on of the debug features when debug=1 and little evidence to aid in determining the cause (of the original pr

Re: [weewx-user] Re: weewx stop working

Not really, no The first part appears to show normal running with archive records every minute - but no log for the startup process The second part, manual running , shows us the startup but only loop data - it runs for under a minute so does not give the coverage for two archive periods (whic

Re: [weewx-user] Re: weewx stop working

here it is. Is this ok what I attach? regards Dne petek, 14. junij 2019 12.45.41 UTC+2 je oseba Andrew Milner napisala: > > Keep running the simulator for a while, but can you now give us the log > from startup for at least two archive intervals FOR SIMULATOR so that we > can be SURE everything

Re: [weewx-user] Re: weewx stop working

Keep running the simulator for a while, but can you now give us the log from startup for at least two archive intervals FOR SIMULATOR so that we can be SURE everything is working as it should be. Then, if that looks ok, can you stop weewx, set debug = 1, restart weewx and again attach the log

Re: [weewx-user] Re: weewx stop working

https://github.com/matthewwall/weewx-interceptor this is what I have for interceptor in weewx.conf [Interceptor] # This section is for the network traffic interceptor driver. # The driver to use: driver = user.interceptor # Specify the hardware device to capture. Optio

Re: [weewx-user] Re: weewx stop working

Yes I did. When I have installed it it worked. Now I have reconfigure it for simulator driver and it works. https://vreme.povej.net so it really is something with driver, what I can do to check what it is? Dne petek, 14. junij 2019 11.24.55 UTC+2 je oseba gjr80 napisala: > > I think people are tr

Re: [weewx-user] Re: weewx stop working

I think people are trying to help, it is just without a debug log it is rather difficult to determine what is going on and therefore what might be wrong. Also, if settings in weewx.conf are being ignored (eg debug=1) it begs the question what else is amiss. So when you installed WeeWX did you r

Re: [weewx-user] Re: weewx stop working

First time I have installed weewx manually, just copy tar on server and install it. Now on new server I have downloaded weewx-3.9.1-1.rhel.noarch.rpm and install it. than install driver interceptor and setup everything. I even changed po

Re: [weewx-user] Re: weewx stop working

as always, my mistake. sorry. On Friday, 14 June 2019 10:48:31 UTC+3, gjr80 wrote: > > I agree something is not right, but it is not WEEWX_ROOT. For an other > than setup.py install WEEWX_ROOT is indeed / - > http://weewx.com/docs/usersguide.htm#Where_to_find_things refers. > > Gary > -- You

Re: [weewx-user] Re: weewx stop working

I agree something is not right, but it is not WEEWX_ROOT. For an other than setup.py install WEEWX_ROOT is indeed / - http://weewx.com/docs/usersguide.htm#Where_to_find_things refers. Gary -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To uns

Re: [weewx-user] Re: weewx stop working

hold on a minute, something is not correct. The section of weewx.conf you posted says WEEWX_ROOT is / whilst the weewx startup says weewx is using /etc/weewx/weewx.conf, which implies that WEEWX_ROOT should be /etc/weewx and not / also debug should be set = 1 in /etc/weewx/weewx.conf - I suspe

Re: [weewx-user] Re: weewx stop working

is your weewx installation really in the root directory as you have got specified in weewx.conf? how did you install weewx ?? On Friday, 14 June 2019 04:25:32 UTC+3, Andrew Milner wrote: > > Have you done what Matthew asked some time ago and run weewx manually - > not as a daemon?? > > Did yo

Re: [weewx-user] Re: weewx stop working

Sorry all of that I already did on old server. Below I did this again, no other logs. This is the reason why I had to reinstall server again and again not working. I run manually again fev times and all what I get in log is # WEEWX CONFIGURATION FILE # # Copyright (c) 2009-2019 Tom Keffer # See

Re: [weewx-user] Re: weewx stop working

Have you done what Matthew asked some time ago and run weewx manually - not as a daemon?? Did you get any LOOP packets logged to the screen when you ran manually?? The log you posted just shows a normal startup - although debug does not appear to be set. Did you edit the correct weewx,conf fil

Re: [weewx-user] Re: weewx stop working

Sorry I already post log from old centos server and it is the same on new centos server. All I have in log is only this Jun 13 18:50:56 povej systemd: Started SYSV: start and stop the weewx weather system. Jun 13 18:50:56 povej weewx[15848]: engine: Using configuration file /etc/weewx/weewx.con

Re: [weewx-user] Re: weewx stop working

what does weex say in the log when it is starting?? weewx outputs a lot of information at startup - so you need to locate the log and post the log to this forum then we may be able to help you further On Thursday, 13 June 2019 11:11:32 UTC+3, Damjan Hajsek wrote: > > Any idea how to solve thi

Re: [weewx-user] Re: weewx stop working

Any idea how to solve this please? Dne torek, 11. junij 2019 22.24.35 UTC+2 je oseba Damjan Hajsek napisala: > > I have installed fresh new server centos 7.6 > also installed fresh installation of weewx 3.9.1 > also installed driver interceptor. > And I get the same result as before. > I have chec

Re: [weewx-user] Re: weewx stop working after upgrading from 3.6.x to 3.9.1

Great, I will look into this thank you. On Wednesday, June 5, 2019 at 1:13:16 AM UTC+2, gjr80 wrote: > > This issue was fixed in v1.0.4. The v1.0.4 code was not released as a > package but can be installed by following the instructions in this post >

Re: [weewx-user] Re: weewx stop working after upgrading from 3.6.x to 3.9.1

This issue was fixed in v1.0.4. The v1.0.4 code was not released as a package but can be installed by following the instructions in this post . Gary On Tuesday, 4 June 2019 13:14:57 UTC+10, gjr80 wrote: > > Agree that WeeWX-WD

Re: [weewx-user] Re: weewx stop working after upgrading from 3.6.x to 3.9.1

Ok, Thanks for the info regarding WU. I might give a look into this, if it is not already taken care of by someone proficient on this topic. The SDR is not failing, it was closed by Weewx, and the message order is somehow wrong. My station is back online since this morning, and did not shutdo

Re: [weewx-user] Re: weewx stop working after upgrading from 3.6.x to 3.9.1

You won’t be getting any forecast from WU using the forecast extension for the time being as it has not yet been updated to work with the new WU API. I suspect your time will be better spent looking into why the SDR driver is exiting and causing the WeeWX engine to shut down. Gary -- You rece

Re: [weewx-user] Re: weewx stop working after upgrading from 3.6.x to 3.9.1

Agree that WeeWX-WD has struck again and caused the error that was posted. Am sure this been fixed in a later version, I will track that one down and post a link as necessary. I also think there is another somewhat more critical issue - refer to the highlighted lines: Jun 3 23:29:29 raspberry

Re: [weewx-user] Re: weewx stop working after upgrading from 3.6.x to 3.9.1

The problem is not with WeeWX, but with the weewxwd3 extension you installed. It does not seem to check for missing data before attempting to calculate humidity. On Mon, Jun 3, 2019 at 2:36 PM St. B. wrote: > Ok, > > Below is the the /var/log/messages generated when running systemctl > restart w

[weewx-user] Re: weewx stop working after upgrading from 3.6.x to 3.9.1

I'm not seeing much here for me to go on, but some more questions: did you change your database? I wonder if it's locked or modified? What happens if you run weewxd /etc/weewx/weewx.conf Paste the output if/when it crashes. On Monday, June 3, 2019 at 5:36:16 PM UTC-4, St. B. wrote: > > Ok,

[weewx-user] Re: weewx stop working after upgrading from 3.6.x to 3.9.1

Ok, Below is the the /var/log/messages generated when running systemctl restart weewx. Weirdly enough systemctl start weewx does not seem to run anything. Stack trace when running from command prompt is as follows : root@raspberrypi:~# weewxd /etc/weewx/weewx.conf Traceback (most recent call

[weewx-user] Re: weewx stop working after upgrading from 3.6.x to 3.9.1

Nothing jumping out. Pasting some logs and debugs would be super helpful. See Help! Posting to weewx user On Monday, June 3, 2019 at 4:49:17 PM UTC-4, St. B. wrote: > > Hi, > > I decided (because my WU forecast where not workin

Re: [weewx-user] Re: weewx stop working

Damian, Still very strange that we do not see debug = 1 echoed in the logs. At this point I am at a loss other than, perhaps you could preface the command with strace so we can see what is going on. I expect it gets to a point where it is just more or less sleeping, doing nothing. I say that

Re: [weewx-user] Re: weewx stop working

Hi I have done this and it is all the same. I created some logs from manually starting weewx. when I start weewx manually sudo weewxd /etc/weewx/weewx.conf' it didn't crash, I stopped it. here it is. http://zerobin.povej.net/?b06b1ad942bc51a2#34Nj1ed+8odSg7jHbjz7AU+WsqZ3yxPjZDB1EPHyVAk= Dne sre

Re: [weewx-user] Re: weewx stop working

Damian, You have to give wee_config a command. >From the usage, you want this: $ sudo wee_config --reconfigure --config=/etc/weewx/weewx.conf (Although you can leave the --config part off, since your conf file is located in the default location). But do be sure to back up the config file first.

Re: [weewx-user] Re: weewx stop working

Hi What I did is first use some old weewx.conf file from last year and doesn't work either. So I tried to reconfigure it but can't when I run wee_config --help I get list of help but when I do this I get wee_config /etc/weewx/weewx.conf No command specified. wee_config --config=/etc/weewx/weewx.co

Re: [weewx-user] Re: weewx stop working

Damian, These logs still do not state debug = 1. It still could be that the weewx.conf isn't being parsed correctly, and isn't even able to read the debug = 1 setting. Did you try my suggestions for how to "rebuild" the conf file? Regards, Leon -- Leon Shaner :: Dearborn, Michigan (iPhone) >

Re: [weewx-user] Re: weewx stop working

the logs that you posted do not have debug enabled the logs that you posted do not show any crashes - they show you starting and stopping weewx 9 times. why do you keep killing weewx? you must do the following: 1 - set debug=1 in /etc/weewx/weewx.conf 2 - start weewx manually, i.e., 'sudo weew

Re: [weewx-user] Re: weewx stop working

Hi I have followed your instruction so I did all as described first turn off monit stop weewx debug = 1 was already set than I run weewx manually here is a log from that http://zerobin.povej.net/?a63b7ac09e222bcc#9Y5+B9WWtxXgUJWTKZWmzElusp9QRgEK5Pde606SvQc= http://zerobin.povej.net/?7d382c267025f

Re: [weewx-user] Re: weewx stop working

at this point in the thread it is not clear what is happening or what is the state of your system. so start over and explain what your configuration looks like now then, to diagnose weewx, do the following: - remove whatever it is that keeps restarting weewx - stop weewx if it is running - set

Re: [weewx-user] Re: weewx stop working

I have never used the interceptor driver but I would expect the interceptor driver should be emitting loop packets which would be printed on the console. I think the fact that you are seeing a blank screen means we have hit on the problem. You are going to need some input from Matthew or an int

Re: [weewx-user] Re: weewx stop working

I have manualls started interceptor, what can I expect from it, because nothing changes? PYTHONPATH=/usr/share/weewx python /usr/share/weewx/user/interceptor.py --device=observer --mode=listen --port= Dne torek, 16. april 2019 11.16.05 UTC+2 je oseba gjr80 napisala: > > There have been no

Re: [weewx-user] Re: weewx stop working

There have been no changes to the database since 3.8.1, but this is not a database problem. WeeWX is event driven and it relies on loop packets and/or archive records from the driver triggering events which then cause archive records to be created and saved to the database, reports to be genera

Re: [weewx-user] Re: weewx stop working

Thank you I did this and no luck. Can you tell me are there any changes in databasebetween version 3.8.1 and the latest version?? If not I will install new weewx with rpm and than use old database. regards Dne petek, 12. april 2019 15.34.53 UTC+2 je oseba Leon Shaner napisala: > > Damian, > > The

Re: [weewx-user] Re: weewx stop working

Damian, The symptoms I mentioned where it seems like weewxd is waiting for input could be due to an issue parsing your conf file. The wee_debug info you posted has these lines: # This section can adjust data using calibration expressions. [1] That looks like garbage. And yet way before that

Re: [weewx-user] Re: weewx stop working

hi here is my debug log. http://zerobin.povej.net/?6a7fc01d0616ffa9#Zj15RUTw5bxNGfoVlibcKTgn5D2oPqPX0Dg+rkHOeR4= don't know what happend here all what I do on server latelly was to uninstall gnome desktop and reinstall it. Maybe is some part of python deleted or something like that? Damian Dne p

Re: [weewx-user] Re: weewx stop working

Damian, It's really strange that there is no mention of debug = 1 in the log. Normally, when debug = 1 is actually working, the log mentions it. :-/ We know you are using /etc/weewx/weewx.conf, because it's there in the "ps -ef" output. Another thing that is strange is while we can see that

Re: [weewx-user] Re: weewx stop working

Let's be very clear here, you have logs they are not missing, that is what you have been posting over the last 12 hours. It would seem that once WeeWX has completed its loading/initialisation something is causing it to die or otherwise not do anything. You say that the last log extract posted w

Re: [weewx-user] Re: weewx stop working

Hi I have checked debug and it is only once and it is on 1. my logs are in /var/log/messages (centos 7) And I already did that but there was no weewx logs. I also have webmin and have filtered out all weewx logs, which you already see it. [root@localhost ~]# ps -ef | grep weewx | grep -v grep roo

Re: [weewx-user] Re: weewx stop working

Hi, Damjan, Just to rule out whether "debug" appears in the log file more than once you could do this: $ grep 'debug' /etc/weewx/weewx.conf If there is a debug = 1 followed later by debug = 0 (and it is not commented out with a preceeding #), then the later one will likely take precedence. An

Re: [weewx-user] Re: weewx stop working

Hi [image: 2019-04-11 18_34_45-_etc_weewx_weewx.conf - root@194.249.178.190 - Editor - WinSCP.png] Yes I really changed debug to 1 in conf file. I am from GMT +2 And I tested, date shows real date and time as it should be Why there is no logs I don't know, that is all what I get for fev hours af

Re: [weewx-user] Re: weewx stop working

Hi, Damjan, I do not see debug output. Did you change debug = 0 to debug = 1 in the conf file? Other than that, there is a thread where folks mentioned issues when the date is off by too much... I can't tell what time zone your host is set to, but I would guess UTC or GMT, no? In my case I ha

Re: [weewx-user] Re: weewx stop working

Here is log with debug enabled. http://zerobin.povej.net/?18327ca6959d12c6#NusymzsEuAoTuXNt9tVsZL1+VG4jZO28VhSVYjJxwC0= Dne četrtek, 11. april 2019 15.17.35 UTC+2 je oseba gjr80 napisala: > > Ok, so you do have logs. The startup log extract you posted looks fine to > me. What's happens next in

Re: [weewx-user] Re: weewx stop working

Ok, so you do have logs. The startup log extract you posted looks fine to me. What's happens next in the log? Need to see at least the next 5 minutes of log. Not that it seems to be required but your attempt at running WeeWX directly failed because WeeWX could not find weewx.conf, you need to pr

Re: [weewx-user] Re: weewx stop working

this log is when I restart weewx http://zerobin.povej.net/?d31ee849647759be#97lZ+kWzpA/GMSj9XL9BOVz6N9QqRWbm513C1W4Qf+c= when I start it directly I get this [root@localhost /]# sudo weewxd weewx.conf Unable to open configuration file /weewx.confTraceback (most recent call last): File "/bin/wee

Re: [weewx-user] Re: weewx stop working

Whether WeeWX runs properly or not there should be some log output indicating WeeWX tried to start. No matter. What happens when you try to run WeeWX directly (http://weewx.com/docs/usersguide.htm#Running_directly). Please post all of the screen output, including the command you entered. Gary

Re: [weewx-user] Re: weewx stop working

I have posted logs and last logs are from april 1. when weewxwas running and latest logs are only when I restart weewx and nothing else. Dne četrtek, 11. april 2019 10.48.17 UTC+2 je oseba gjr80 napisala: > > I am afraid until you can find where your WeeWX log is being written there > is little

Re: [weewx-user] Re: weewx stop working

I am afraid until you can find where your WeeWX log is being written there is little we can do to help you with WeeWX. Perhaps some Googling or a support forum for your flavour of Linux might be able to help. Gary On Wednesday, 10 April 2019 17:00:37 UTC+10, Damjan Hajsek wrote: > > Any help he

Re: [weewx-user] Re: weewx stop working

Any help here please? I am stuck, nothing works. Dne nedelja, 07. april 2019 21.57.30 UTC+2 je oseba Damjan Hajsek napisala: > > I have set debug = 3 > but there is all of log I have, I posted it already. > my console is connected and working. > > > Dne nedelja, 07. april 2019 20.56.17 UTC+2 je os

Re: [weewx-user] Re: weewx stop working

I have set debug = 3 but there is all of log I have, I posted it already. my console is connected and working. Dne nedelja, 07. april 2019 20.56.17 UTC+2 je oseba vince napisala: > > On Sunday, April 7, 2019 at 11:23:59 AM UTC-7, Damjan Hajsek wrote: >> >> I have installed with setup.py. >> Now I

Re: [weewx-user] Re: weewx stop working

On Sunday, April 7, 2019 at 11:23:59 AM UTC-7, Damjan Hajsek wrote: > > I have installed with setup.py. > Now I am thinking to use rpm and database from old setup. > Any idea what I need to do to transfer all what I need? > >> >> I think you need to slow down and stop changing things so we can try

Re: [weewx-user] Re: weewx stop working

I have installed with setup.py. Now I am thinking to use rpm and database from old setup. Any idea what I need to do to transfer all what I need? Dne nedelja, 07. april 2019 17.35.45 UTC+2 je oseba vince napisala: > > On Sunday, April 7, 2019 at 8:25:22 AM UTC-7, Damjan Hajsek wrote: >> >> Ok how

Re: [weewx-user] Re: weewx stop working

I use default centos logging didn't change anything and this worked fev days ago and suddenly stopped. What about if I install this regullyary with rmp and than use mysql database which is already stored? Now I have manually installed weewx. Dne nedelja, 07. april 2019 18.29.22 UTC+2 je oseba Th

Re: [weewx-user] Re: weewx stop working

Well, it's hard to diagnose much of anything without the log. A Google search shows that some CentOS installations do not use a traditional logging daemon. For these, you must use the command journalctl. Try that. -tk On Sat, Apr 6, 2019 at 11:13 PM Damjan

Re: [weewx-user] Re: weewx stop working

On Sunday, April 7, 2019 at 8:25:22 AM UTC-7, Damjan Hajsek wrote: > > Ok how to do that? > I have removed abrt-server and still the same problem. > > > Dne nedelja, 07. april 2019 15.17.01 UTC+2 je oseba jo...@johnkline.com > napisala: >> >> The problem is in the log: >> abrt-server: Package 'wee

Re: [weewx-user] Re: weewx stop working

Ok how to do that? I have removed abrt-server and still the same problem. Dne nedelja, 07. april 2019 15.17.01 UTC+2 je oseba jo...@johnkline.com napisala: > > The problem is in the log: > abrt-server: Package 'weewx' isn't signed with proper key > > -- You received this message because you ar

Re: [weewx-user] Re: weewx stop working

The problem is in the log: abrt-server: Package 'weewx' isn't signed with proper key -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscr...@googleg

Re: [weewx-user] Re: weewx stop working

Ok here is log from april 1. there I can see reports from weewx and that was last reports. Than on april 5. and 6. when I restarted weewx fev times, that is all what is in log. I have put it in pastebin because there is alot of log. http://zerobin.povej.net/?93548ecff653710f#UC94AO2wvBbQS6nOPg5K

Re: [weewx-user] Re: weewx stop working

Perhaps it is the language barrier but I for one am a little confused. Is there any log output from WeeWX, anywhere? You said: I can see that in log > perhaps it is best that you post whatever it is you can see. Otherwise we are just guessing. Gary On Sunday, 7 April 2019 16:13:15 UTC+10, Dam

Re: [weewx-user] Re: weewx stop working

Yes it is missing. I have setup debug to 3 and when I start weewx I can see that in log, but only that and nothing else. I have disabled SElinux and it is the same. Dne nedelja, 07. april 2019 06.14.05 UTC+2 je oseba Thomas Keffer napisala: > > On CentOS, your log should be in /var/log/messages.

Re: [weewx-user] Re: weewx stop working

On CentOS, your log should be in /var/log/messages. Are you saying that is missing completely? On Sat, Apr 6, 2019 at 2:08 PM Damjan Hajsek wrote: > I have done some more test and this is what I found out. > detected unhandled Python exception in '/usr/bin/weewxd' > don't know is this is the re

[weewx-user] Re: weewx stop working

I have done some more test and this is what I found out. detected unhandled Python exception in '/usr/bin/weewxd' don't know is this is the reason? Dne sobota, 06. april 2019 19.45.36 UTC+2 je oseba Damjan Hajsek napisala: > > I noticed that weewx stop working, so I have checked log and there is