evel@lists.sourceforge.net
Cc: Jeff Stillinger
Subject: Re: [wsjt-devel] Hamlib error
As Mike has already said, USB is not a valid com port. So the error message
says exactly what the problem is.
Linux should be something similar to this: /dev/ttyUSB0 or /dev/ttyUSB1.
My Icom 7100 is set to /dev/tty
As Mike has already said, USB is not a valid com port. So the error
message says exactly what the problem is.
Linux should be something similar to this: /dev/ttyUSB0 or /dev/ttyUSB1.
My Icom 7100 is set to /dev/ttyUSB0 for cat control.
Windows is a completely different beast. Again, the er
Is the port you selected actually named "USB" ? If so that's not a valid port
name in either Linux or Windows.
Mike W9MDB
On Sunday, April 28, 2024 at 05:53:18 PM CDT, Eric Lundstrom via wsjt-devel
wrote:
Installed wsjtx_2.6.1_amd64.deb on a lubuntu OS and received the hamlib
Installed wsjtx_2.6.1_amd64.deb on a lubuntu OS and received the hamlib error
shown below.
Installed wsjtx-2.6.1-win64.exe on a windows 10 OS and received basically the
same error.
The hamlib DLL on the Windows machine has a file date of 1/10/2023, a size of
9.7 mb, and a file name of libhamli
rate setting could be changed or COM port number.
73, Reino OH3mA
-Original Message-
From: Marty Wayne via wsjt-devel [mailto:wsjt-devel@lists.sourceforge.net]
Sent: 23. heinäkuutata 2022 4:29
To: WSJT software development
Cc: Marty Wayne
Subject: Re: [wsjt-devel] Hamlib Error
I can’t
I can’t even get the radio and wsjt-x to communicate. I misspoke when I said
that the Hamlib error happened while using FT8. Actually, I had taken a short
break. I believe I shut down wsjt-x and restarted when I returned. That is
when aI started getting the Hamlib error. I hadn’t changed th
As a diagnostic..
While sending CQ for example..
Reduce the transmit power,
by both audio and transmitter settings and see
if the phenomenon goes away at lower powers.
If with the output minimized the phenomenon
persists then it is probably not RFI related.
If you find a reduced output power th
If it runs at startup but fails during/after transmit than it is probably RFI.
Here are some potential solutions -- ordered by cost.
#1 Free - Move USB cables to another port -- some ports are more susceptible
than others.#2 Free -- Check your grounding system. rod-outside-the-shack is a
common
I used a RasPi4 2.6.0 rc1 and a FTDI to control my 1996 ft1000mp
with a USB audio dongle for field day.
The RadPi4 was headless using No Machine so I could
operate remotely from the TV room with my Android phone
or laptop.
FTDI has less problems especially with some other software
works very well
Marty,
I have used a simple USB to RS-232 converter cable with my FT-1000MP for CAT
control. You have already Signalink for audio audio/PTT.
73, Reino OH3mA
-Original Message-
Marty,
In your list of equipment, I don't see a CAT interface. The Signalink is
only a sound card interface. T
Marty,
In your list of equipment, I don't see a CAT interface. The Signalink is
only a sound card interface. There is no CAT interface. The error
message shows that WSJT-X was trying to access the FT-1000MP's CAT. To
get around this, In WSJT-X, go to Settings - Radio. Near the top, where
it s
Likely to be an RF ingress issue, vs a software problem.
George J Molnar
College Park, Maryland
KF2TFM19ma
> On Jul 21, 2022, at 1:28 PM, Marty Wayne via wsjt-devel
> wrote:
>
> I tried operating with WSJTx 2.5.2 and 2.5.4 with same issue.
>
> 73,
>
> Marty, W6NEV
> _ . . . . _ _
I tried operating with WSJTx 2.5.2 and 2.5.4 with same issue.
73,
Marty, W6NEV
_ . . . . _ _ _ . . . . _ . . . . . _
mcway...@comcast.net
408-234-8023
> On Jul 21, 2022, at 10:23 AM, Marty Wayne wrote:
>
> I was working 20 Meter FT-4 and at one point I got a Hamlib error,
> commun
I was working 20 Meter FT-4 and at one point I got a Hamlib error,
communication timed out. See report below. Im not computer savvy. What might
be the issue?
Rig-FT-1000MP
iOS 12.5
SignaLink USB interface
WSJTx 2.5.2
WSJTx 2.5.4
Hamlib error: Communication timed out
rig_get_vfo: returning -5
doing a QSO. Much better
now but there must be other code hiding from view.
Thanks
Sent from Mail for Windows 10
From: Tim Selner
Sent: Friday, January 29, 2021 6:15 PM
To: Black Michael; WSJT software development
Subject: Re: [wsjt-devel] Hamlib error in RC4
Mike, operation is better
fi they persist. Rebooting the PC
now to make sure that is not the issue.
Sent from Mail for Windows 10
From: Black Michael via wsjt-devel
Sent: Friday, January 29, 2021 5:09 PM
To: wsjt-devel@lists.sourceforge.net
Cc: Black Michael
Subject: Re: [wsjt-devel] Hamlib error in RC4
This has been
. Rebooting the PC
now to make sure that is not the issue.
Sent from Mail for Windows 10
From: Black Michael via wsjt-devel
Sent: Friday, January 29, 2021 5:09 PM
To: wsjt-devel@lists.sourceforge.net
Cc: Black Michael
Subject: Re: [wsjt-devel] Hamlib error in RC4
This has been fixe in hamlib now
This has been fixe in hamlib now.
Any Icom with a 1-byte mode value would see this error.
Mike W9MDB
On Friday, January 29, 2021, 01:39:50 PM CST, Tim Selner
wrote:
Hamlib error in RC4
I installed WSJT-X RC4 and I am having issues. I am running Windows 10 and an
IC-735. Ever
l for Windows 10
From: Bill Somerville
Sent: Friday, January 29, 2021 3:14 PM
To: wsjt-devel@lists.sourceforge.net
Subject: Re: [wsjt-devel] Hamlib error in RC4
On 29/01/2021 19:21, Tim Selner wrote:
Hamlib error in RC4
I installed WSJT-X RC4 and I am having issues. I am ru
ourceforge.net
<mailto:wsjt-devel@lists.sourceforge.net>
*Subject: *Re: [wsjt-devel] Hamlib error in RC4
On 29/01/2021 19:21, Tim Selner wrote:
Hamlib error in RC4
I installed WSJT-X RC4 and I am having issues. I am running
Windows 10 and an IC-735. Everything was working
Sorry, I did not follow where you want me to save the file. I am not sure
where the WSJT config files are located.
Sent from Mail for Windows 10
From: Bill Somerville
Sent: Friday, January 29, 2021 3:14 PM
To: wsjt-devel@lists.sourceforge.net
Subject: Re: [wsjt-devel] Hamlib error in RC4
On
I am available at 920-371-5149
Sent from my iPhone
> On Jan 29, 2021, at 3:15 PM, Bill Somerville wrote:
>
>
>> On 29/01/2021 19:21, Tim Selner wrote:
>> Hamlib error in RC4
>>
>>
>>
>> I installed WSJT-X RC4 and I am having issues. I am running Windows 10 and
>> an IC-735. Everything
On 29/01/2021 19:21, Tim Selner wrote:
Hamlib error in RC4
I installed WSJT-X RC4 and I am having issues. I am running Windows
10 and an IC-735. Everything was working fine on RC3 but now I am
have problems transmitting using RC4. Freq control looks to be OK but
I am not getting consisten
Hamlib error in RC4
I installed WSJT-X RC4 and I am having issues. I am running Windows 10 and an
IC-735. Everything was working fine on RC3 but now I am have problems
transmitting using RC4. Freq control looks to be OK but I am not getting
consistent PTT. When I go to Settings / Radio I ca
I just pushed a commit that has a new dummy device without set_vfo or get_vfo.
I was able to patch it to work with this situation so this should apply to any
older Icom rigs and Yaesu rigs that don't have set_vfo capability and/or
get_vfo capability.
I'm still waiting for my tester to get a curre
Hi Mike,
thanks for chasing this down. I have some confusion whether there are
two issues, one with direct rig control and another when using rigctld.
I would be good to test both, let me know if a test version of WSJT-X is
needed with your patch for any platform required? Although in this cas
I've got a patched version that I sent to one of the testers
On Wednesday, June 3, 2020, 06:26:20 AM CDT, Bill Somerville
wrote:
Mike,
I believe it is quite reasonable to implement rig_get_vfo for the FT-891,
FT991, and similar. In this case it may be that a implementation
Mike,
I believe it is quite reasonable to implement rig_get_vfo for the
FT-891, FT991, and similar. In this case it may be that a implementation
that always returns VFO A is correct as I don't believe these rigs use
VFO B for anything other than SPLIT Tx transmit frequency. That aside,
what i
The FT-991 is one that doesn't have the ability to query which VFO is active
and doesn't have the ability to query "current VFO" either.
Since we allow currVFO to pass through to the Icoms it's also now passing
through to all rigs.
So it seems the only choice here would be to set the current VF
Mike,
OK, WSJT-X checks for both of those return codes when it makes its first
attempt to get the current VFO. So Hamlib must not lie about that
capability and return a success status, otherwise WSJT-X continue on the
basis that rig_get_vfo() works for the current rig.
Is this error because
Don't know for sure...but it's been that way since version 3.3
As the error codes say in rig.h
RIG_ENIMPL, /*!< 4 function not implemented, but will be */
RIG_ENAVAIL, /*!< 11 Function not available */
On Tuesday, June 2, 2020, 05:35:42 PM CDT, Bill Somerville
wrote:
gt; To: WSJT software development
> Subject: Re: [wsjt-devel] Hamlib error with GA release
>
> Folks,
>
> I am observing the same issue on Windows 10 (pre 2001 release) with the
> FT-991 here but also on a FT-897D using a CT-17.
>
> I have also noted the same issues in
Mike,
don't do that, the whole point of that query is to find out if the rig
can be queried for the current VFO, the result determines how the rig is
handled via the Hamlib API. Hamlib should return "not implemented", why
is an "invalid parameter" error being returned?
73
Bill
G4WJS.
On 02/
@lists.sourceforge.net]
*Gesendet:* Dienstag, 2. Juni 2020 21:21
*An:* 'WSJT software development'
*Cc:* Black Michael
*Betreff:* Re: [wsjt-devel] Hamlib error with GA release
I need one of the Yaesu owners to follow the directions in this
youtube video and send me their debug.txt file.
https://www.y
Hi Mike,
Find enclosed the debug.txt file. (I’ve included some more lines.)
73 de Uwe, DG2YCB
Von: Black Michael via wsjt-devel [mailto:wsjt-devel@lists.sourceforge.net]
Gesendet: Dienstag, 2. Juni 2020 21:21
An: 'WSJT software development'
Cc: Black Michael
Betreff: Re: [
OK. I figured out my mistake with following the video.
When I run the rigctl-wsjtx.exe, and I try to test with F to get
frequency I get the get_freq: error = Invalid Parmeter.
On 6/2/2020 1:45 PM, Kim gross wrote:
Thanks for the help Mike
For my setup com3 is primary port, and com is
evelopment
Date: Tuesday, June 2, 2020 at 1:47 PM
To: 'WSJT software development'
Subject: Re: [wsjt-devel] Hamlib error with GA release
Hi Bill and others,
I have the same error here at my PC: WSJT-X v2.2.0 GA cannot communicate with
my FT991 via normal Com Port. Audio works nor
Thanks for the help Mike
For my setup com3 is primary port, and com is the secondary.
I am trying to follow the directions but when I run the rigcrtl -m 1035
-r com3 -R com -s 38400 it never comes back. If I don't do both -r and
-R I get an error. If I set both -r and -R to come3, it drops
I need one of the Yaesu owners to follow the directions in this youtube video
and send me their debug.txt file.
https://www.youtube.com/watch?v=0yZG1-v-BXA
Mike W9MDB___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.
, DG2YCB
Von: Bill Somerville [mailto:g4...@classdesign.com]
Gesendet: Dienstag, 2. Juni 2020 19:25
An: wsjt-devel@lists.sourceforge.net
Betreff: Re: [wsjt-devel] Hamlib error with GA release
Hi Jay,
is this issue also associated with no receive audio to WSJT-X?
73
Bill
G4WJS.
On 02
helps. Let me
know what else you might need.73 Jay. KA9CFDSent from my U.S.Cellular©
Smartphone
Original message From: Bill Somerville
Date: 6/2/20 12:34 (GMT-06:00) To: wsjt-devel@lists.sourceforge.net Subject:
Re: [wsjt-devel] Hamlib error with GA release
Hi Jay
<mailto:g4...@classdesign.com>
Sent: Tuesday, June 2, 2020 10:29 AM
To: wsjt-devel@lists.sourceforge.net<mailto:wsjt-devel@lists.sourceforge.net>
Subject: Re: [wsjt-devel] Hamlib error with GA release
Hi Jay,
is this issue also associated with no receive audio to WSJT-X?
73
Bill
G4WJS.
O
message
From: Bill
Date: 6/2/20 11:44 (GMT-06:00)
To: WSJT software development
Subject: Re: [wsjt-devel] Hamlib error with GA release
I have run into the same issue. Just installed the 2.2.0 GA on Windows
10 and receive "Hamlib error: Invalid parameter while getting current
freq
Same issue with my FT991.Hamlib error: Invalid parameter while getting current
frequency.Jay KA9CFDSent from my U.S.Cellular© Smartphone
Original message From: Bill Date:
6/2/20 11:44 (GMT-06:00) To: WSJT software development
Subject: Re: [wsjt-devel] Hamlib error with
GA
I have run into the same issue. Just installed the 2.2.0 GA on Windows 10
and receive "Hamlib error: Invalid parameter while getting current
frequency". Radio - FT991A. Also, no display on the waterfall but shows
activity in the decode list. Previous versions worked fine and JTDX still
works normal
Windows 64 bit, upgraded to GA release I get a hamlib error and can not
do anything. Reinstalled RC3, system works fine. FT991A.
___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
Hello!
I am trying to connect my IC 7000 to the WSJT-X, but I only get the message:
"hamlib error: Communication bus error while getting current frequency"
Can you help?
I have downloaded the latest version of your program; v.1.7.0 r7405 and
I have Windows 10 on my computer.
Hope you can help
On 08/11/2016 20:39, Dimitrios Ntoulas wrote:
Rigctld works fine with cqrlog, fildigi, grig.
My setup is
Rig <-> Rigctld <-> App (cqrlog, fildigi, grig)
Hi Dimitris,
are you using the version of rigctld provided with WSJT-X? It is named
rigctld-wsjtx.
73
Bill
G4WJS.
---
48 matches
Mail list logo