Hi Chris,


What s the voltage of your power supply?



So you have decided to make your own colloidal silver. This is a smart move on your part for several reasons. First and foremost is the fact that you will be in complete control of the quality of your product. Colloidal silver is basically a very easy product to make. The process that generates colloidal silver is called electrolysis. It is the same process that is involved in electroplating. This process moves tiny little bits of a metal ( ions ) from one piece of metal parens the anode and program to the cathode, which can theoretically be any conductive metal, but in good practice should also be pure silver. You need a vessel to hold whatever amount of pure distilled water that represents the amount of colloidal silver product that you will end up with. It is very important that this is steam distilled water. Not de-ionized. Not ozonated. We are fortunate in the United States to have this available at stores such as Wal-Mart, Walgreens, and many others. The quality (purity) of the distilled water that you buy by the gallon will vary. It is produced in large plants, and the quality depends on the water quality that they start off with and how well they have maintained their distilling equipment. I will show you how to do a quick check to make sure that the distilled water is suitable for making colloidal silver before you use it.



We will start off with the famous but tricky 3-9 method. This method entails the purchase of 3 9 volt batteries and connecting them in series to gain 27 volts. You then simply attach the positive and negative battery terminals to two pieces of silver, which are immersed in water. You are then supposed to sit and watch this until you see a cloud, a yellow cloud, of bubbles emerging from the positive electrode and heading for the negative electrode. The problem with this method is that by the time you see these bubbles the process has run away in terms of current density and is producing overly large silver particles and has never reached the potentially high level of Ionic concentration. This results in an inferior product, even when the person using it is very diligent. We need to explain what we mean when we use the term quote current density quote. The silver electrode that is connected to the positive battery terminal is called the anode. The anode provides the atoms of silver. It will have a certain surface area. There is an optimum level of current density for the purpose of generating the highest level of Ionic concentration before the formation of actual silver particles begins. If this level is exceeded, then particles start forming too early in the process and the process must be stopped before the particles become so large that the water begins to take on a color, starting with a yellowish tinge. This indicates that particles larger than 40nm have begun to form. Many years ago, before we had reasonably priced visible lasers available, we used the presence of a yellow tinge of color as an indicator that the process was finished. Even using the method with current limiting, to prevent runaway, if the process goes on too long, the yellow tinge will appear. There is nothing wrong with having colloidal silver with a slight yellow tinge. The particles are still of the size that will do you no harm.



Many times people complain about the length of time that a process requires. Because the water is a very pure to start with as in the process of distillation removes any Ionic content. Ions are what makes water conductive, therefore the current is very low to start with. It builds up very gradually, and as it does the resistance between the electrodes decreases, thereby increasing the current. The greater the distance between the electrodes, the greater resistance. Therefore, one easy way to speed the process is to initially place the electrodes in close proximity. By using a resister as a current limiting device between the batteries and an electrode you can do this quite safely, as even if you touch the electrodes together to form a short circuit, no harm will be done. The resister will limit the current to a safe value. If you place a voltmeter across the current limiting resistor, it will initially show very little voltage being dropped across the resister, because the current will be very low. You will be able to see the current increasing as the ions increase in number as the voltage across the resister will increase proportionately as this occurs. When you observe this effect, you can then gradually move the electrodes further apart. This will substantially decrease the amount of time involved in making the product. You may find that there are people who will suggest adding some salt to the water to speed the process. This is very bad advice. You end up making silver chloride, and a series of unknown compounds that are combinations of other impurities contained in the salt. Please do not do this. There are other people, who will tell you that it is okay to just use tap water. There is a case of a congressman from South Dakota, who did this and turned blue. I don't know whether or not it did him any permanent harm. But it doesn't seem like a good idea to me.



----- Original Message ----- From: "Arnold Beland" <abela...@comcast.net>
To: <silver-list@eskimo.com>
Sent: Wednesday, October 31, 2007 5:37 PM
Subject: CS>a question about silver????



--
The Silver List is a moderated forum for discussing Colloidal Silver.

Instructions for unsubscribing are posted at: http://silverlist.org

To post, address your message to: silver-list@eskimo.com

Address Off-Topic messages to: silver-off-topic-l...@eskimo.com

The Silver List and Off Topic List archives are currently down...

List maintainer: Mike Devour <mdev...@eskimo.com>