James,

To safely measure the current in the secondary circuit of the
10,000 volt transformer I would recommend the following:

With the power off attach your inductive pickup to one of the
high voltage wires making sure that no other wire (low or HV)
or metal is within several inches of the pickup

This HV wire is only 10,000 volts IN RELATION to another wire
on the transformer secondary.  With the HV transformers in the
TV's I work on (15,000 Hz,  not 60 Hz) there can be some
voltage leaking to other wires or metal, less likely with 60 Hz.

To be on the safe side you probably should use a less
expensive DMM.  You can pick one up for as low as $30 (US).
Make sure that it has a 10 megohm input impedance (if that's
what your Fluke has).  Then if somehow it blows out you don't
lose much.  Nice to have a backup meter anyhow.

By the way will your pickup measure a few milliamps?  Maybe
I should have asked that first!!  An inductive pickup may be very
inaccurate with such a small current flow.  I cannot imagine how
cutting and then carefully splicing the wire would hurt anything.
Then you could use a $10 analog VOM (volt-ohm-milliampmeter.)

If you have any suggestions for using another low voltage instead
of 30VDC (15V?  150V?) and best current levels I would be most
appreciative.  I am using the gallon jar with the large electrodes.

Good luck and let me know what happens,

Bil Green



>Hi Bill
>
>Can you tell me the most practical way to measure the milliamps at the
>secondary of a nominal  120 V 60 Hz 10KV center-tapped transformer?  I
>would rather not cut the wire, because the maker says the configuration is
>very sensitive to even minor changes in the physical layout.
>
>I have a Fluke 87 and an inductive pickup, but am spooked about frying the
>meter.  I asked Fluke, and they said the transformer was not rated for that
>voltage.  Other than an insulation breakdown, what distortion of the
>measurement or harm to the meter would you consider.
>
>Thanks in advance,
>
>
>James Osbourne Holmes
>[email protected]
>
>
>-----Original Message-----
>From: 2001 TV  VCR [SMTP:[email protected]]
>Sent: Friday, November 12, 1999 1:40 PM
>To: [email protected]
>Subject: CS>LOW OR HIGH VOLTAGE?
>
>I have not seen anyone discuss the best method for
>making high quality CS.  One of the manufacturers of
>high voltage (10,000 volts AC) CS generators claims
>that the low voltage (30 volts DC) systems are worthless.
>
>I have been using 30VDC first using thin silver wires and
>a 16 oz. jar and now a gallon jar with a much larger silver
>electrode.  Without current limiting most of the silver ends
>up on the cathode (negative electrode).  Some of you
>suggested limiting the current to a milliamp or so and
>going for quite a few hours.
>
>Can some of you offer more opinions and suggestions
>along these lines.  Let us know what type of equipment
>and voltages/currents you are working with if getting good
>results.  It is so important that all of us end up with CS that
>is effective and safe to use.
>
>If any of you have questions about electrical or electronic
>circuits involving you CS equipment I can help.
>
>Bil Green
>2001 TV VCR
>
>
>
>
>--
>The silver-list is a moderated forum for discussion of colloidal silver.
>
>To join or quit silver-list or silver-digest send an e-mail message to:
>[email protected]  -or-  [email protected]
>with the word subscribe or unsubscribe in the SUBJECT line.
>
>To post, address your message to: [email protected]
>
>List maintainer: Mike Devour <[email protected]>
>