James,

To wire an inexpensive VOM in series with the 10,000 VAC
the first consideration is that cheap VOM's don't measure
AC milliamps (only DC).  Sorry I did not think of that last time.

I don't know what Marshall was referring to about adding a
diode.  Adding one in series with the meter would change the
HVAC to DC.

This is more accurate:  Wire a 1,000 ohm resistor  in series
with one of the HV leads and attach your meter leads ACROSS
this resistor.  Set the meter to read at least 10VAC at first.

A 1/2 watt resistor will do.  When you power up, a reading of
1 VAC will indicate 1 mA,  5 VAC is 5 mA,  etc.  Adding this
1,000 ohm resistor to a 10,000 V circuit will reduce the current
by less than a hundredth of 1 mA! (when running at 1 to 10 mA).

You can use a lower voltage setting on the meter if necessary
for better resolution.  Thank you for the tips on CS.

Bil



>Hi Bill,
>
>Thank you for your time and expertise.  I think I will try the RS meter
>first.
>
>I thought that paddle meters were made which could just be placed on the
>wire, but I have not been able to find one.  That seems the least intrusion
>into the circuit.
>
>Can you describe in detail how to hook up a cheap analog meter.  I could do
>it at the generator tank end of the circuit without cutting the HV leads.
> Perhaps physically awkward, but I could do it without cutting the wire.
>
>I don't know much about low voltage silver, except that it works.  I
>started with 3 9v batteries and a glass.
>
>>From my observations of the experiences of the people on this list a lot
of
>different systems work.  I am expert in none.  I would have to dig through
>a lot of not-well-organized mail to find the answers to your questions.
> Address them to the list and you will get a flood of answers.
>
>One thing is pretty obvious;  water quality---purity and conductivity---is
>crucial to most, if not all processes.  And you can get water a bit too
>pure.
>
>The second most important factor is limiting current.  As more Ag gets in
>the water, it becomes more conductive and puts more silver in the water
>faster,  which raises the cond....you get the point.  Most agree that big
>current makes big particles. Most everybody seems to agree, that with DC
>generators, current limiting circuits improve the quality of the sol.  I
>think they use a 555.
>
>Let me know if you can't find what you are looking for and I will try and
>dig it up.
>
>James Osbourne Holmes
>[email protected]
>
>
>-----Original Message-----
>From: 2001 TV  VCR [SMTP:[email protected]]
>Sent: Saturday, November 13, 1999 12:13 AM
>To: [email protected]; [email protected]
>Subject: Re: CS>LOW OR HIGH VOLTAGE?
>
>James,
>
>To safely measure the current in the secondary circuit of the
>10,000 volt transformer I would recommend the following:
>
>With the power off attach your inductive pickup to one of the
>high voltage wires making sure that no other wire (low or HV)
>or metal is within several inches of the pickup
>
>This HV wire is only 10,000 volts IN RELATION to another wire
>on the transformer secondary.  With the HV transformers in the
>TV's I work on (15,000 Hz,  not 60 Hz) there can be some
>voltage leaking to other wires or metal, less likely with 60 Hz.
>
>To be on the safe side you probably should use a less
>expensive DMM.  You can pick one up for as low as $30 (US).
>Make sure that it has a 10 megohm input impedance (if that's
>what your Fluke has).  Then if somehow it blows out you don't
>lose much.  Nice to have a backup meter anyhow.
>
>By the way will your pickup measure a few milliamps?  Maybe
>I should have asked that first!!  An inductive pickup may be very
>inaccurate with such a small current flow.  I cannot imagine how
>cutting and then carefully splicing the wire would hurt anything.
>Then you could use a $10 analog VOM (volt-ohm-milliampmeter.)
>
>If you have any suggestions for using another low voltage instead
>of 30VDC (15V?  150V?) and best current levels I would be most
>appreciative.  I am using the gallon jar with the large electrodes.
>
>Good luck and let me know what happens,
>
>Bil Green
>
>
>
>>Hi Bill
>>
>>Can you tell me the most practical way to measure the milliamps at the
>>secondary of a nominal  120 V 60 Hz 10KV center-tapped transformer?  I
>>would rather not cut the wire, because the maker says the configuration is
>>very sensitive to even minor changes in the physical layout.
>>
>>I have a Fluke 87 and an inductive pickup, but am spooked about frying the
>>meter.  I asked Fluke, and they said the transformer was not rated for
>that
>>voltage.  Other than an insulation breakdown, what distortion of the
>>measurement or harm to the meter would you consider.
>>
>>Thanks in advance,
>>
>>
>>James Osbourne Holmes
>>[email protected]
>>
>>
>>-----Original Message-----
>>From: 2001 TV  VCR [SMTP:[email protected]]
>>Sent: Friday, November 12, 1999 1:40 PM
>>To: [email protected]
>>Subject: CS>LOW OR HIGH VOLTAGE?
>>
>>I have not seen anyone discuss the best method for
>>making high quality CS.  One of the manufacturers of
>>high voltage (10,000 volts AC) CS generators claims
>>that the low voltage (30 volts DC) systems are worthless.
>>
>>I have been using 30VDC first using thin silver wires and
>>a 16 oz. jar and now a gallon jar with a much larger silver
>>electrode.  Without current limiting most of the silver ends
>>up on the cathode (negative electrode).  Some of you
>>suggested limiting the current to a milliamp or so and
>>going for quite a few hours.
>>
>>Can some of you offer more opinions and suggestions
>>along these lines.  Let us know what type of equipment
>>and voltages/currents you are working with if getting good
>>results.  It is so important that all of us end up with CS that
>>is effective and safe to use.
>>
>>If any of you have questions about electrical or electronic
>>circuits involving you CS equipment I can help.
>>
>>Bil Green
>>2001 TV VCR
>>
>>
>>
>>
>>--
>>The silver-list is a moderated forum for discussion of colloidal silver.
>>
>>To join or quit silver-list or silver-digest send an e-mail message to:
>>[email protected]  -or-  [email protected]
>>with the word subscribe or unsubscribe in the SUBJECT line.
>>
>>To post, address your message to: [email protected]
>>
>>List maintainer: Mike Devour <[email protected]>
>>
>