Yes, but that is what all of my ABIs are set to (I didn't know any different when I deployed them.) But they are working fine, so I can't complain. :)
On Tue, 25 Nov 2003, Blazen Wireless wrote: > BUT keep in mind setting it back to default only works if you have YOUR > settings in the firmware burned in ;-) > If not then it sticks them back to the SSID of ANY and IP address of > 192.168.0.22 > ----- Original Message ----- > From: "Sam" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Tuesday, November 25, 2003 7:50 AM > Subject: Re: [smartBridges] Hosed network > > > I had that happen to a couple of my customers using ABI. I had them reset > the ABI using the button on the power shot, and it fixed it. (Might save > you a truck roll if it happens again) > > Sam > > On Tue, 25 Nov 2003, Blazen Wireless > wrote: > > > what firmware are you using on the ABO I would suggest 0.01.07 or 0.01.08 > as > > the latest ones to try...I have seen this happen when I logged into a > > customers radio to switch AP names or WEP on or off and it scrambles the > > SSID and gives all kinds of hex characters etc. I had to truck roll to the > > clients house to fix it.. > > > > > > ----- Original Message ----- > > From: "John K. McReynolds" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Tuesday, November 25, 2003 6:58 AM > > Subject: [smartBridges] Hosed network > > > > > > This will start off-topic, but then get back on topic... > > > > We have an Orinoco AP2000 at a water tower. We have one radio card in > this > > unit. We also have a YDI ECII acting as the backhaul. The two units are > > connect via eachother's ethernet ports. No switch or router in between. > > This > > has worked great for sometime now...until the last week or so. > > > > About a week ago, we started noticing a massive slow down on our > > network...then > > the AP could not be reached with a ping or any admin tools...i.e., the > > network > > was down. So, figuring maybe it was equipment failure, I replaced all the > > AP > > equipment at the tower...different AP2000, different card, different coax > > jumper...and bang! It was back to normal. I did change channels however. > > > > Now, here we are a week later (today). Same thing is happening. > > > > We have WET11's and ABO's as CPE on our network. I personally have a > WET11 > > at > > my home...the WAN light now comes and goes...this morning it is totally > off. > > > > We have also noticed that after the first "outage", the ABOs had lost > > association and upon further inspection, the AP that each was associated > > with > > was just a bunch of random garbage...like sHOFW3EHNFSALX, instead of the > > name > > of our AP. We re-associated them and they worked fine. > > > > So, time for my questions: > > 1) Is there some setting that the ABOs need to have to "play nice" with an > > AP2000? > > 2) If an ABO freaks out and loses its association, could it hose the > AP2000 > > also? > > 3) Should I put a switch or router between the ECII and the AP2000? > > > > I am really in need of assistance here...I am about to my ropes end with > > this > > stuff...any pointers or suggestions will be more than welcomed. > > > > Many thanks in advance, > > > > JOHN > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > smartBridges <yournickname> > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > > smartBridges) > > Archives: http://archives.part-15.org > > > > > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > > Archives: http://archives.part-15.org > > > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org > > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges > <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
