9 juni 2015, Bill Somerville <g4...@classdesign.com> skrev: > On 09/06/2015 22:34, <hlundst...@sk0mt.net> wrote: > > > > Hi again, reports from the schack:Hi Hans, > > > > > You say- > > In recent Windows you must set speaker volume sliders while the device is > > active. I recommend setting the level for Tx from teh USB audio driver from > > your rig menu item "USB Level". > > This is the problem speaker volume adjusted at first TX but for next TX > > volume level back on 0 and no output. You can not sit and adjust for every > > TX sequence. Rig USB level set to 78 as always ...Where do you have the > > "Pwr" slider at the right hand side of the WSJT-X main window? This control > > is an attenuator which is directly connected to the Windows level control > > for the output audio device you select in "Settings->Audio->Output" which > > you would normally have at the top (0dB) unless you want a Tx power less > > than the minimum output from your rig's carrier/power control. > > > > > > > > > CI_V Transcieve mode set to off as you said > > > > > > > > > > Iinitially it was iimpossible to change "TransmitAudio Source" as it was > > not highlighted. I had to fiddle with PTT methods to change to rear/data. > > Fixed it once but can not repeat that process now.The IC-7200 doesn't not > > support automatic switching by CAT commands to the rear/USB audio source so > > this option is disabled for your rig. You must set the mode and SET menu of > > the rig to suit your connections. If you want USB Audio driver modulation > > via USB to the rig modulator then I suggest you set the rig SET menu item > > "Modulation input (Data on)" to U(USB) and select Mode as "Data/Pkt" in > > WSJT-X (or if you want to set mode manually you can set it to "None"). That > > way when you start WSJT-X it will select USB-DATA on your rig and the Tx > > audio will be taken from teh USB Audio driver bypassing the speech > > processor and also with its own level setting with the rig SET menu "USB > > Level" setting. > > > > > > > > > All in all no progress so far. > > > > Hans > > 73 > Bill > G4WJS. > > > 9 juni 2015, Bill Somerville <g4...@classdesign.com> skrev: > > > Hi Again Hans, > > > > > > I forgot to mention, > > > > > > on Icom rigs you must disable "CI-V Transceive" mode in the rig menu. > > > That mode is on by default but it generates unsolicited CAT traffic which > > > causes data collisions and lost CAT conversations. > > > > > > 73 > > > Bill > > > G4WJS. > > > > > > On 09/06/2015 21:50, Bill Somerville wrote: > > > > > > > On 09/06/2015 21:24, <hlundst...@sk0mt.net> wrote: > > > > > > > > > > > > > > > > > > Hallo,Hi Hans, > > > > > > > > > > > > > > Installing program was easy, but all the rest worse.Sorry you are > > > > > having some issues with WSJT-X. > > > > > > > > > > > > > > Using ICOM IC-7200 with connection to rig via USB ( Silicon Labs > > > > > CP210x USB to UART Bridge) like all other ICOM 7200 and 7600 users. > > > > > That has worked fine with all versions of WSJT/WSPR except for this > > > > > last version of WSJT-X. > > > > > ' > > > > > Settings feels like a random happening sometimes. Options are there > > > > > sometimes and sometimes not. > > > > > I used: > > > > > CAT Control > > > > > Serial port COM8 (as usual) > > > > > 19200 baud 8bits one stop bit no handshake (all as usual) > > > > > PTT method CAT Port Com8 (fixed via a roundabout way, not needed in > > > > > the older versions .... perhaps neither here ?)WSJT-X now allows PTT > > > > > through the CAT port using serial lines RTS or DTR, or via another > > > > > serial port using RTS or DTR or if your rig supports it, via a CAT > > > > > command. Your rig has the capability to SEND with a CAT command and I > > > > > recommend that method to you. > > > > > > > > Set the PTT Method to CAT. > > > > > > > > > > > > > > Transmit Audio Source: Rig set to data mode expecting info via USB. > > > > > Setting Rear/Data ( fixed in a very roundabout way as it was not > > > > > reachable and initially set to Front/MIc)Some rigs use a different > > > > > CAT command to take transmit audio from the read data connection, the > > > > > setting is there for those rigs and it is only enabled for those > > > > > rigs. Icom rigs select the Tx audio source according to the rig > > > > > modulation mode and via rig menu settings. I believe the 7200 takes > > > > > Tx audio from the rear data socket when USB-DATA mode is selected. > > > > > You need to change the rig setting "Modulation input (Data on)" to > > > > > U(USB) to take Tx audio from the USB audio driver. > > > > > > > > > > > > > > Mode USB (tried the other two settings with no luck)None - doesn't > > > > > change the mode of your rig. USB sets the mode to USB. Data/Pkt sets > > > > > the mode of your rig to Data. The latter is the best choice so long > > > > > as you have selected the correct Tx audio source in your rig menu. > > > > > > > > > > > > > > Split Op None > > > > > Test CAT was OK > > > > > Test PTT was OK > > > > > RX works fine > > > > > TX starts with resetting audio out to 0 that is no TXIn recent > > > > > Windows you must set speaker volume sliders while the device is > > > > > active. I recommend setting the level for Tx from teh USB audio > > > > > driver from your rig menu item "USB Level". > > > > > > > > > > > > > > TX sometimes go on for everIf you can provide repeatable steps to > > > > > demonstrate that issue please report them here, > > > > > > > > > > > > > > As I understand it you have changed code to control audio out setting > > > > > and rig control compared to all the other versionsYes we use a new > > > > > audio subsystem that works much better and is more consistent across > > > > > all the platforms we support. Also with rig control, because advanced > > > > > dual mode JT9+JT65 and soon to be released EME Doppler tracking > > > > > features need tight and accurate transceiver control, much work has > > > > > been done to improve the stability of CAT and PTT functionality. > > > > > > > > > > > > > > All the best Hans sm0vyi73 > > > > Bill > > > > G4WJS. > > > > > > ------------------------------------------------------------------------------ > > _______________________________________________ > wsjt-devel mailing list > <wsjt-devel@lists.sourceforge.net> > <https://lists.sourceforge.net/lists/listinfo/wsjt-devel> >
------------------------------------------------------------------------------
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
