säker så jag kollade med min bank, så de
skulle se om det kommit rätt.
När kommer den nya sändaren ut till försäljning?
Funkar ditt paypal nu?
Med vänliga hälsningar
Kjell Claesson
___
Nut-upsuser mailing list
Nut-upsuser@lists.alioth.deb
.6.4
> Network UPS Tools - Generic HID driver 0.37 (2.6.4)
> USB communication driver 0.32
> This Liebert device (06da:0002) is not (or perhaps not yet) supported
> by usbhid-ups. Please make sure you have an up-to-date version of NUT. If
> this does not fix the problem, try runnin
tisdagen den 16 december 2014 15.36.29 skrev Frantz de Germain:
Hello,
Hi Frantz,
I'm testing an APC SMT3000RMI2U connected to an USB port with Nut 2.7.2.
I've got the message :
interrupt pipe disabled (add 'pollonly' flag to 'ups.conf' to get rid of
this message)
I've been looking
lördagen den 29 juni 2013 11.28.14 skrev Mike.:
8--snip-
Hi Mike,
Thanks for the quick reply.
I checked the log file (which, admittedly, I should have done before I
posted about the problem :) ).
Here's the command and the corresponding log message:
The problem is that I had a crash on my backup ;-( so I lost the
paper on the specific commands for 5125.
So if someone have the command specifications on pw5125, can you check
if this is the case for the 5125 that it is impossible to set auto off delay.
Regards
Kjell Claesson
Co
torsdagen den 21 februari 2013 14.39.10 skrev Daniel Lopes de Carvalho:
Hi,
Hi Daniel
Does anyone know how to make NUT works with Powerware 5125?
I already tried serial communication (genericups and bcmxcp) and USB
(usbhid-ups and bcmxcp_usb), but without success.
Do you have
On Wednesday 21 November 2012 13.49.35 Daniel Lopes de Carvalho wrote:
Hi Kjell, thanks for your answer.
OK
We bought this UPS in the end of 2011. The model is: Powerware 5125
Rack-Mount UPS 5000/6000 VA.
That is new.
I tried setting the usbhid-ups, but without success.
OK
[Ups01]
On Wednesday 21 November 2012 12.31.41 Daniel Lopes de Carvalho wrote:
Hi.
Hi Daniel,
I'm looking for a way to configure an Eaton Powerware 5125 under Debian
Squeeze (amd64) with USB port.
How old is the ups?
I use a 5125 but it has only serial (or snmp). If this usb card is new,
it may
Kjell Claesson
___
Nut-upsuser mailing list
Nut-upsuser@lists.alioth.debian.org
http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/nut-upsuser
torsdagen den 12 januari 2012 15.30.02 skrev Gregory Skelton:
Hi,
Hi Gregory,
I have more information, I did some more digging and found a debugging
mode for the driver.. So this what I'm seeing. Any ideas how I get
around the PW_COMMAND_START_BYTE?
Thanks for any help.
Greg
Have
On Thursday 11 August 2011 10.55.39 Gémes Géza wrote:
Hi,
Hi Géza.
I've got an AEC Star T4110 connected with an RS232 port by a megatec cable.
On the list of supported devices
(http://www.networkupstools.org/stable-hcl.html) there is only one AEC
device, so I tried genericups with
On Thursday 11 August 2011 15.37.09 Gémes Géza wrote:
Thank you for your help.
Unfortunately it isn't working.
OK.
I have nut version 2.4.3-1ubuntu3.1 , so have tried the megatec driver:
[aec]
driver=megatec
port= /dev/ttyS0
The output of # /lib/nut/megatec -DD -a
Hi.
Hi Daniel,
I'm using ubuntu 10.04 and I'm in the process of buying a ups.
This is it (eaton 5115 ups) with usb interface
http://powerquality.eaton.com/05146561-5591.aspx?CX=3
I had a look at the ups compatibility chart here:
http://www.networkupstools.org/stable-hcl.html
But I
Hi,
PS. What is the meaning of: battery.capacity: 0.03 ?
This is a mapping problem. The UPS is reporting 100% battery capacity is
available and I mistakenly mapped this to the battery capacity (Ah)
value. I will remove this later on.
Kewl!
This is already done in the trunk by
OK
On Monday 03 January 2011 20:40:17 Arjen de Korte wrote:
Citeren Kjell Claesson kjell.claes...@epost.tidanet.se:
So start to send the output of:
lsusb -v
Cut out the part about the ups, and we have a look on it.
Make that
lsusb -v -d 075d:0300
to save
Hi James,
$ sudo upsdrvctl start
Network UPS Tools - UPS driver controller 2.4.3
Network UPS Tools - Generic HID driver 0.34 (2.4.3)
USB communication driver 0.31
Using subdriver: CyberPower HID 0.3
OK, the driver seems to start.
But have you started the daemon (upsd)?
$ sudo upsc
Hi Vladimir,
Dears,
I finally resolve my problem, I just make symbolic link:
[t...@box var/run/]# ln -s -T /var/state/ups/ nut
Now I finally got services online:
# /sbin/service ups start
Starting UPS driver controller:[ OK ]
Starting upsd:
OK,
This is out from blazer_usb -DD -a mustek -u root :
http://pastebin.com/63QHfdU0
1.606976 blazer_vendor: short reply
1.607091 Vendor information read 1 failed
2.612971 blazer_vendor: short reply
2.613078 Vendor information read 2 failed
3.618972
to start (exit status=1)
---STOP---
Can anyone in any way help me toward making this work?
Try to switch the rx/tx line. Or messure the signal with a voltmeter.
Regards
Kjell Claesson
___
Nut-upsuser mailing list
Nut-upsuser
Ok guys I get this errors:
Hi,
Network UPS Tools – UPS driver controller 2.4.1
Network UPS Tools – Generic HID driver 0.34 (2.4.1)
USB communication driver 0.31
No matching HID UPS found
my ups.conf is:
[ap1000]
driver = usbhid-ups
port = auto
I’ve also tried to set a specific
Hello!
Hello,
I have a box that monitors the surrounding environment and sends a signal
to a debian machine when it is time to shut down, according to the
developers of the box it uses and old standard of UPS signaling. It is
super simple, it just changes the DCD status to high when it is
Hi ricman,
8snip
send: D
read: timeout
blazer_status: short reply
Status read 3 failed
No supported UPS detected
Network UPS Tools - Megatec/Q1 protocol serial driver 1.51 (2.4.1)
where am i wrong?
1. Your ups.conf ?
2. What command did
Hi,
Citeren Jon Bendtsen jbendt...@laerdal.dk:
I have a R3000XR, and i use bcmxcp using a seriel port out, since i
can not find a USB port on the UPS.
I do have a USB2serial on the host.
I still experience that NUT upsstats.cgi says the UPS battery is at
97%, and some days later
To Arjen.
Hi, do we have any active developer on the powercom driver.
It seems to support the XPCC ups. The problem seems to be
the calculation of the voltage and ups.load.
This thread should give some info needed to make it work.
Anything to move to dev list?
/Kjell
OK Jeff,
Jeffrey B. Green
OK Jeff,
Kjell Claesson wrote:
Then if you can check the speed on the port. The powercom driver is using
1200 b/s.
% stty -F /dev/ttyS0
speed 1200 baud; line = 0;
min = 0; time = 0;
ignbrk -brkint -icrnl -imaxbel
-opost -onlcr
-isig -icanon -echo -echoe -echok -echoctl -echoke
Great Jeff,
Jeffrey B. Green wrote:
I'll experiment with the driver variable options, however, if you know
the correct (or almost correct) settings, then that info would be
greatly appreciated.
No my baby is the bcmxcp driver, so my knowledge in the calculations done
in the powercom
Jeff,
The previous values were under load, which I forgot to mention. It has a
~500W server and 10W switch on it.
Then the ups.load is low also.
But you should not do the LB shutdown test with the server attached.
It may power off without a warning.
/Kjell
OK.
The readings just before the nut initiated server shutdown due to LB was:
% upsc xtreme
battery.charge: 47.9
driver.name: powercom
driver.parameter.linevoltage: 120
driver.parameter.manufacturer: XPCC
driver.parameter.modelname: XVRT-1000
driver.parameter.pollinterval: 2
Hi Jeff,
Jeffrey B. Green wrote:
However, they are fairly simple tools and not configurable beyond
the command line arguments specifying the serial line and polling times.
Sorry, small correction. Not polling times, rather the breakout delay
time and the UPS shutdown delay time.
This
2009/8/28 Thomas Zulliger thomas.zulli...@quiksilver.com.au
Hi Arnaud and Thomas.
Can not reproduce it.
upsdrvctl -DD start
Network UPS Tools - UPS driver controller 2.4.1
Starting UPS: pw3105
exec: /lib/nut/bcmxcp_usb -a pw3105
Network UPS Tools - BCMXCP UPS driver 0.21 (2.4.1)
USB
OK,
Should I try changing the polling frequency just to see if it helps?
Don't think it would help. If it would be a problem with poll frequency, the
error should be continuous and constant. The same is if there was any problem
with the driver to the specific model of ups you are running.
OK David,
Kjell,
Thanks for your time in replying.
The cable is a regular commercial shielded cable and is only six feet
long. Grounding should not be an issue, everything is on a single
circuit with a single ground and is powered through the UPS itself, all
in one cabinet, so all grounds
OK Jon, just a comment.
is bcmxcp a eaton driver?
For some years ago Eaton purchased Powerware, but the driver
was developed before that. On the nut 1.4 series it was Martin Schroeder
that made the driver. But it was dropped, so i was sitting with some Powerware
ups'es that I have to monitor.
Hi all,
Hi Greg,
I've got a Powerware 5110 UPS that I'm trying to set up with nut in
Ubuntu. I've installed nut and configured the first two files:
$ cat /etc/nut/nut.conf
MODE=standalone
$ cat /etc/nut/ups.conf
[pw5110]
driver = bcmxcp_usb
port = auto
# port =
, it now happened at a time where I could log
in to see in real time what is happening and:
$ upsc PW5125 | grep status
ups.status: TRIM
This is fixed in a later release of the driver.
From change log:
Wed Jan 14 21:45:10 UTC 2009 / Kjell Claesson kjell.claes...@epost.tidanet.se
- drivers
Hi again,
Just a couple of values are bothering me here... hoping anyone else
with an R3000XR can advise.
Nice to see that you got it running.
battery.charge: 33.1
battery.runtime: 442
battery.voltage: 129.2
This may indicate a faulty battery in the pack.
You have 10x12volt, and it
On Tue, May 26, 2009 at 09:51:31PM -0400, Brother Railgun of Reason wrote:
Hi,
ups.conf looks like this:
[tokamak]
driver = bcmxcp
port= /dev/tty00
baud_rate = 19200
desc= HP R3000XR (main rack)
(Oops. That's *after* changing to the 19200
Greg and Arnaud
I missed to add that I'm also interested in this one: unset USB_DEBUG
lsusb -d06da:0002 -v on your 9.04. I can't find it back in the thread.
@Kjell: do you see anything that could lead to that kind of regression?
I'm not sure that it's on our side though.
I can not set the
tisdag 21 april 2009 14:43:28 skrev Greg:
Hi Kjell,
Hi Greg,
Sorry for the late reply been doing a lot of testing.
No problem.
I got the package from
http://ipkg.nslu2-linux.org/feeds/optware/cs05q3armel/cross/stable/nut_2.4.
1-1_arm.ipk It pretty much pre-compiled which are then extracted
fredag 17 april 2009 15:36:24 skrev Greg:
Hi Kjell,
Hi. Sorry for the delay.
Thanks for the follow up. Answers below...
OK Greg, I can not locate the package you used for installing NUT,
but the device should be capable of running NUT.
I was thinking if HAL is enabled in the package so the
torsdag 16 april 2009 02:25:58 skrev Greg:
Hi everyone,
Hi Greg,
Been searching like crazy to find an answer to this. I have even read some
of the source code but cannot figure this one out.
I have installed nut 2.4.1 on my QNAP 409 Pro. (command: ipkg install nut)
I have configured the
fredag 20 mars 2009 15:03:25 skrev Attila Csontos:
Hi Attila,
I was trying build new driver from svn, I think, that driver is now OK.
There is output from PW9130.br
debug level is '2'
Connected to UPS on /dev/cua/a with baudrate 9600br
Length of meter map: 92
måndag 16 mars 2009 14:32:44 skrev Arnaud Quette:
OK all,
8--snip--
It happens only when I start driver with -DD (or more 'D'). When I run
only with -D, it working normally.
all the debug outputs there are at level 2. so nothing but
söndag 15 mars 2009 23:57:18 skrev Attila Csontos:
Hi Kjel,
I was trying both, but I got message unknow UPS (or similar like
this). Maybe nut
does not support this model UPS till now.
This sounds strange. Maybe Arnaud can answer this.
B.t.w. Have you checked that the nut driver have right
lördag 28 februari 2009 20:37:44 skrev waa-...@revpol.com:
Hi Bill,
8--snip-
Here is a current upsc output: (on batteries for about 50 mins now)
--[snip]--
# upsc smart...@localhost
battery.alarm.threshold: 0
battery.charge: 000.0
Hi Again Bill,
Checked up the manual for the APC.
It looks like you have to do some configuration with the POWERCHUTE SOFTWARE.
Reset the battery date and make a runtime calibration test.
If this is not done it may as it say in the Problem and/possible cause
THE LEDS IN THE BATTERY BAR GRAPH
lördag 28 februari 2009 16:36:54 skrev Charles Lepple:
There's a subtle difference here - adding '-D' to the upsdrvctl
command line increases the verbosity of upsdrvctl, not the driver that
it starts.
For testing, you would want something like:
/lib/nut/usbhid-ups -D -a compaq-ups
fredag 27 februari 2009 18:35:11 skrev Arnaud Quette:
2009/2/27 KP Kirchdoerfer kap...@bering-uclibc.de
8---snip--
Try this driver again, but make sure to add
productid = 1f06
to the ups.conf entry for this device. Chances are
fredag 27 februari 2009 18:48:58 skrev KP Kirchdoerfer:
8snip---
Bus 001 Device 002: ID 03f0:1f06 Hewlett-Packard
Device Descriptor:
bLength18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass
fredag 27 februari 2009 19:09:27 skrev KP Kirchdoerfer:
Am Freitag, 27. Februar 2009 18:54:00 schrieben Sie:
fredag 27 februari 2009 18:48:58 skrev KP Kirchdoerfer:
8snip---
If you ask me to run upsdrvctl with -D I'll don't geht more
fredag 27 februari 2009 19:37:42 skrev KP Kirchdoerfer:
You can rise the debug level by adding D. So try -DDD .
I have not worked with the usbups_hid driver but it should give
some more info.
Yep; I tried that also, but didn't got more output
OK, then we have a bastard ;-(
The only
lördag 14 februari 2009 14:40:07 skrev Doug Parsons:
OK Doug,
I saw those as well but need the online model as I have had some issues
with offline models and rapid power cycles. When you have an automatic
transfer switch between two ups units and your equipment, the rapid cycles
can cause
fredag 13 februari 2009 20:52:41 skrev Arnaud Quette:
Hi Doug,
8---snip
Really hate that MGE drop those models as I really like the quality and
design.
not that easy!
This part of MGE has not been droped, but sold to Eaton.
All the good
Den Tuesday 13 January 2009 23.27.02 skrev Arjen de Korte:
Hi Arjen,
It would be nice if the driver would also report
'battery.voltage.nominal', so that clients don't have to guess it. We
need this for instance when drawing bar graphs in the CGI programs.
That take some more time, This is in
Den Tuesday 13 January 2009 03.40.58 skrev Mathew McBride:
Hi Mathew,
I managed to obtain the original cable for this UPS, and it turns out,
according to some poking with a multimeter, that it is a simple straight
through. I managed to connect the UPS and setup NUT ok.
One thing I would
Den Wednesday 31 December 2008 06.31.05 skrev Herman C Lau:
To all,
Hi Herman,
I attempted to configure the UPS tools for the Tripp-Lite SmartOnline
1500VA 2U rackmount UPS. I followed the instructions from the 'upsdrvctl
start' output and posted the diagnostic information below.
Is my
Den Saturday 20 December 2008 16.39.55 skrev Mathew McBride:
Hello all,
Hi Mathew
I have obtained a Compaq T700 H UPS sans-cable. My research indicates it
would've come with a HP #201092-001 cable, and from previous posts on
this list, it speaks upscode2, possibly being a rebadged Eaton unit.
Den Saturday 20 December 2008 20.29.43 skrev Charles Lepple:
Hi Charles,
On Sat, Dec 20, 2008 at 11:40 AM, Kjell Claesson
kjell.claes...@epost.tidanet.se wrote:
Attache a pdf with info from Compaq. Se if it helps.
(attachment removed from posting to list)
If we're allowed to distribute
Den Thursday 18 December 2008 17.05.59 skrev du:
Hi Kjell,
Hi Mohanjith,
The UPS is from one of the local manufacturers IE Tec. They no longer
produce this UPS. I tried all drivers with no luck, namely apcsmart,
belkin, belkinunv, bestuferrups, bestups, cpsups, cyberpower,
energizerups,
Den Tuesday 16 December 2008 15.48.48 skrev Sudirikku Mohanjith:
Hi,
Hi Mohanjith,
I cannot find Mustek drivers or PowerMust drivers that support Mustek
UPSes in the NUT source. Looking at the source I see that mustek is
added to svn:ignore. Could I know where I can get either driver or
know
Den Tuesday 16 December 2008 20.39.17 skrev Sudirikku Mohanjith:
Hi Kjell,
OK Mohanjith,
Thanks for the quick reply, much appreciated.
I tried the megatec driver with no luck. Bellow you will find part of
the ups.conf and the output from upsdrvctl.
From /etc/nut/ups.conf
[patriot]
Den Tuesday 09 December 2008 18.39.58 skrev Aldo Caruso:
Hi,
Hi Aldo,
I have an UPS Powerware 5110 ( usb connection ), on Linux OS is
Debian 4.0
Good info, but it would be better to know the nut version. And the driver
version number also.
The /etc/ups.conf file setting is:
[myups]
Den Tuesday 28 October 2008 17.39.25 skrev Seann Clark:
Hi Seann and Arjen,
Could not keep me from looking at this.
The driver looks OK, and changing the timing (delays) in it is not going to
help.
Then I turned to google. Looks like there is a regression in the kernel.
Den Monday 27 October 2008 17.59.44 skrev Seann Clark:
All,
Hi Seann,
8snip-
What I am seeing that is the problem now is that the driver starts
correctly, and initially displays information back from the UPS, but on
any
Den Wednesday 03 September 2008 15.56.11 skrev Jerome BENOIT:
OK Jerome,
Here is the full list:
battery.charge: 100
battery.temperature: 000
battery.voltage: 274.0
driver.name: belkin
driver.parameter.pollinterval: 2
driver.parameter.port: /dev/ttyS0
driver.version: 2.2.2
Den Tuesday 02 September 2008 20.11.28 skrev Jerome BENOIT:
Hello !
Hi Jerome
On the manual and the box, I read:
Delta GES N-Series 6kva (on line series)
On the other hand, upsc gives
ups.mfr: BELKIN
This depends on the driver. If the request for manufacturer
fails to return anything, it
Den Monday 01 September 2008 18.04.22 skrev Jerome BENOIT:
Hi again Jerome,
Not 100% sure but it looks like it is tha same as belkin use.
So for start, try the belkin driver's and then the megatec driver.
the driver belkin is the good one !
OK, can you send some info to the list.
Product
Den Saturday 30 August 2008 21.31.44 skrev Jerome BENOIT:
Hello List,
Hi Jerome,
I would like to control the big Delta box that protect the cluster of my
group: I am not familiar with those kind of machine, but quite familiar
with (Debian) Linux.
That is good.
Does anyone know which NUT
Den Sunday 02 March 2008 04.53.29 skrev Greg:
Hi Greg,
I'm not sure if this is the right list to send this to but anyway heres
a new entry for your UPS hardware compatibility list (stable)
Think most of the devs is also monitoring this list.
Manufacturer - UPSonic Model - PC POWER UPS PCP600
PROTECTED]:~/nut-trunk$
Ideas?
Kjell Claesson wrote:
Den Monday 18 February 2008 10.51.35 skrev Daniel Nyström:
Hi Daniel,
This is fixed in tha latest trunk and also in the testing branch that is
going to be the next release.
You can grab a tarball from http://buildbot.ghz.cc/public
/daniel/nut-trunk/drivers'
make: *** [install-recursive] Error 1
[EMAIL PROTECTED]:~/nut-trunk$
I guess it's pretty simple, since all other files works.
Kjell Claesson wrote:
Den Monday 18 February 2008 15.25.26 skrev Daniel Nyström:
OK,
There have been some updates to the configure
Den Wednesday 30 January 2008 16.11.15 skrev Chencho Pc-cito:
Hi all.
Hi Chencho,
I'm under Ubuntu 7.10 server
I use a SALICRU UPS Advance
I install nut and nut-usb, write some config files, but i cannot connect to
UPS.
At ups.conf i wrote:
[salicru]
driver = newhidups
port = auto
Hi Patrick,
Den Wednesday 09 January 2008 05.11.57 skrev Patrick Ohearn:
Hello,
I am attempting to monitor my two Powerware 3110 UPS from Gentoo Linux
using nut-2.2.0, kernel-2.6.22.1 via USB. From what I can gather around
the net (circa 2005) things with USB on this UPS just didn't work. Has
Hi Daniel, (Eller hejsan.)
Den Monday 07 January 2008 09.28.41 skrev Daniel Nyström:
I've got some strange problem with NUT on my 5115 on Debian Etch:
---snip---
$ sudo ./bcmxcp_usb -DDD -a 5115
Network UPS Tools - BCMXCP UPS driver 0.13 (2.3.0-1181)
Warning: This is an experimental
Den Saturday 01 December 2007 00.11.21 skrev Radu:
Hi Radu,
I'm trying to get a Powerware 5125 UPS running using the bcmxcp driver,
but I get the following errors:
video2:~# /sbin/upsdrvctl start
Network UPS Tools - UPS driver controller 2.0.4
Network UPS Tools - BCMXCP UPS driver 0.10
Den Friday 09 November 2007 13.09.32 skrev Arjen de Korte:
I have a PW9120 hooked up via a serial cable running NUT 2.0.4.
When running upsc I cant see any parameter that looks like it would
trigger a shutdown. Theres is
nothing like battery.charge.low: 30 or battery.charge.warning: 30.
Den Thursday 08 November 2007 16.11.11 skrev Tobias Balle-Petersen:
Tobias Balle-Petersen wrote:
Hello Arjen.
Arjen de Korte wrote:
Adding 'baudrate = 9600' to the 'ups.conf' entry for this UPS should fix
this.
Strange, it tells me this is not supported. I'm on 2.0.4.
Ahh... It
Den Wednesday 07 November 2007 12.06.11 skrev Tobias Balle-Petersen:
OK Tobias,
I have tried two different USB-cables. The one that came with the UPS and
another one I had lying around. I have tried both ports on the computer
(Apple mac G4).
Was there any difference in the communication ?
Den Friday 02 November 2007 13.00.46 skrev Tobias Balle-Petersen:
Hello...
Hi Tobias.
I have a PowerWare 9120 attached via USB to my Debian system.
My ups.conf looks like this:
[ups1]
driver = bcmxcp_usb
port = auto
desc = PowerWare 9120
When testing the
Hi Niels,
Den Friday 10 August 2007 13.26.56 skrev Niels Baggesen:
On Thu, Aug 09, 2007 at 04:59:13PM +0200, Bernd Markgraf wrote:
that's indeed not so good... the ietf mib reports them OL but misses some
values. like the 3 input phases, temperature etc and gives me
battery.runtime.low of 1
Den Thursday 26 July 2007 01.19.00 skrev Stuart Rackham:
Hi
Hi Stuart,
I'm having a problem with the bcmxcp_usb driver FSD command: everything
seems to work apart from:
upsmon -c fsd
8snip
This part have been answered.
One peculiarity --
Den Tuesday 19 June 2007 13.12.48 skrev [EMAIL PROTECTED]:
Hello All
Hi Varain,
I have a MicroDowell ups (BBox BP 1000) connected to a Gentoo box by serial
cable. If I try to start the driver , I see the following :
Network UPS Tools - CyberPower text protocol UPS driver .05 (2.0.5)
Den Wednesday 20 June 2007 07.21.57 skrev [EMAIL PROTECTED]:
8snip---
Thank you, but for now I'll try the powerpanel driver (as Arjen advised).
I'll let you know if things work out.
Yes there have been some changes to the drivers. Some have merged into
OK Eric,
Den Tuesday 22 May 2007 08.56.08 skrev Eric S. Raymond:
Kjell Claesson [EMAIL PROTECTED]:
Or install the udev rules and replug the ups.
Did that. Manual startup of the driver now works without -u root,
indicating (I think) that the udev rools are doing their job. This
8
Hi Steve,
Just updated the trunk, so do an 'svn up' to update the trunk.
Follow the advise from Peter. Was not thinking about the configure
flags. So run 'configure --help' and set the paths.
Regards
Kjell
sön 2007-05-20 klockan 09:14 +0100 skrev [EMAIL PROTECTED]:
Hi Kjell,
Kjell
Hi,
lör 2007-05-19 klockan 14:24 +0100 skrev [EMAIL PROTECTED]:
Hi all,
I've more-or-less got NUT 2.0.4 working with my Powerware Prestige
1000VA UPS (serial), but unfortunately NUT is flagging LOW_BATTERY
continuously, which is a tad embarrassing when power fails ;-)
Can you upgrade to
Hi Russ
fre 2007-05-18 klockan 11:16 -0400 skrev Russ Romano:
Can anyone give me insight into upsrw?
I have a cyberpower PR2200 UPS (running an experimental version of the
powerpanel driver hot off the presses by Arjen (thanks Arjen!!)).
When I try to run upsrw -s xyz=abc to set any
Hi Andreas.
Sorry to say but this is just brought to our attention on the
development list (2 hours ago). This ups seems to have a different
product id.
It means that it maybe using different protocols. So switch to
development list and follow up on the discussion.
Regards
Kjell
fre
Hi
ons 2007-04-18 klockan 15:51 +0800 skrev Gregory Orange:
Arnaud Quette wrote:
2007/4/17, Kjell Claesson [EMAIL PROTECTED]:
It all seems to work but the initial errors or warnings concern me. I'm
running stable 2.05 built from source.
This come from the baudhunting function
ons 2007-04-04 klockan 16:23 +1200 skrev Douglas Pearless:
Hi,
Hi Douglas,
I have a Comapq T2400H model 242688-003 and do not have the special
cable to connect it to my serial port.
I have tried all sorts of cable wirings that I found on the net,
including ones for the powerware 5119
Hi Douglas,
tor 2007-04-05 klockan 08:08 +1200 skrev Douglas Pearless:
Debian, latest stable, upsdrvctl --version gives 2.0.1 Cheers Douglas.
That's not so good. The upscode2 driver was entered into the 2.0.2
release. And nut is now on 2.0.5 in stable (Minus a bug in the bcmxcp
driver :-) )
OK Arjen,
I think i need more time in my bed.
tor 2007-03-29 klockan 08:42 +0200 skrev Arjen de Korte:
THANKS, but the 'megatec' driver only works whith windows OS via USB,
and i need it for red hat OS with USB-serial connection...
No need to be upset, what Arjen de Korte was referring to
Hi,
tor 2007-03-29 klockan 18:24 +0200 skrev Massimo Martinelli:
Alle 20:22, mercoledì 28 marzo 2007, Kjell Claesson ha scritto:
Yes the status is used for shutting down the system. So it would be
needed to make a correct shutdown .
I noticed that you are running version 2.0.4. I think
Hi Massimo,
ons 2007-03-28 klockan 16:36 +0200 skrev Massimo Martinelli:
Hi
I set up my ups with driver snmp-ups, and it get recognized as a AEC T2003.
In the nut-cgi upstats page input/output/load are displayed corectly, but the
Status field is marked as Not supported.
Is Status
Hi Gonzalo,
ons 2007-03-28 klockan 16:22 -0300 skrev gonzalo campuris:
THANKS, but the 'megatec' driver only works whith windows OS via USB,
and i need it for red hat OS with USB-serial connection...
No need to be upset, what Arjen de Korte was referring to was that the
ups use the megatec
Hi Theo,
You can try to run the driver only with the ups.conf.
Locate the bcmxcp_usb driver. then run this command.
/path/to/bcmxcp_usb -DD -a powerware
(exchange the /path/to with the right path)
Now it should spit out som debug info if the communication is ok.
You should also upgrade to
.
Regards
Kjell Claesson
tor 2007-03-01 klockan 09:37 +1100 skrev Paul Battaglia:
Hi All,
I'm trying to communication with the HP r3000 XR UP using the latest
stable build and I'm getting the following errors. Can anyone
enlighten me with the errors below and what other course of action I
can
Hi Steve.
sön 2007-02-04 klockan 03:30 +1100 skrev Steve Simeonidis:
I have an FC5 system with a powerware 5110 usb ups.
The system seems to find the UPS
--
[EMAIL PROTECTED] src]# lsusb
Bus 004 Device 001: ID :
Bus 003 Device 002: ID 0592:0002
Hi Gregory,
tis 2007-01-30 klockan 14:43 +0900 skrev Gregory Orange:
Hi,
I've browsed the archives back for a few months and nothing has jumped
out at me as being helpful, but since there doesn't seem to be a search
facility it's certainly possible I've missed what I'm looking for.
Anyway,
Hi Doug,
ons 2006-11-15 klockan 22:22 -0500 skrev Doug Reynolds:
8snip
I haven't figured out what the F060 or the 0S is. they always stayed the
same. when the UPS went dead and
turned off, it would still reply with the same reply, but all the
1 - 100 of 129 matches
Mail list logo
