The 450i is extremely sensitive to any transition noise on the pulse. There's a hidden command in the cambium radios which you may want to try. I'm sending you a email off-list with it in caseyou want to try it.
On Thu, Nov 24, 2016 at 3:14 PM, Kurt Fankhauser <lists.wavel...@gmail.com> wrote: > Ok, I just put a new PMP450i on a tower and am running into the exact same > problem the Original Poster had here. I have the Gigabit Power Injector > plus Sync and it is blinking for receiving sync from another Sync Injector > in the same enclosure via the included jumper cable and the AP is running > in Autosync+ Freerun and it is not showing receiving any sync at all and it > is decided to Generate its own Sync. Has been running for a couple hours > now. Will keep checking back here. > > On Tue, Nov 22, 2016 at 1:51 PM, That One Guy /sarcasm < > thatoneguyst...@gmail.com> wrote: > >> all this talk of the new units i opened our box of them, is there a guide >> for the 10/100 and gigabit powerinjector jumper settings per brand? >> is it just the same as http://tickets.packetflux.c >> om/downloads/poeinjectorjumpers.pdf only with the pin order backward? >> and if a guy put a 3pin connector on the A/B selector, would that >> effectively put the two inputs in parallel? >> >> On Tue, Nov 22, 2016 at 11:57 AM, Forrest Christian (List Account) < >> li...@packetflux.com> wrote: >> >>> Depends on the power circuitry on the airfiber. My guess is it would be >>> ok. >>> >>> If you have a base unit, you can actually turn off the sync on that port >>> and the injector will remember it, so you don't have to put a base unit in >>> the field with it, just for the programming. (You'd set the poweron >>> column for the sync row for that port to '0'). >>> >>> On Tue, Nov 22, 2016 at 8:37 AM, Kurt Fankhauser < >>> lists.wavel...@gmail.com> wrote: >>> >>>> I just received my first powerinjector + sync today. If I want to power >>>> some Airfibers with these do I need to turn the sync off for those ports? I >>>> don't see a jumper to turn off sync, is it ok to provider sync on a port >>>> with an Airfiber? Does it hurt anything? It looks to me like the only way >>>> to turn off sync is buy the additional site monitor base thing to hookup to >>>> it and turn it off through the web interface? >>>> >>>> On Mon, Nov 21, 2016 at 2:39 PM, George Skorup <geo...@cbcast.com> >>>> wrote: >>>> >>>>> I have four 5GHz 450i's running on our office tower fed from a GigE >>>>> PowerInjector+Sync. They're running 14.1.2. They received sync shortly >>>>> after boot, DFS, etc. BTW, no GigE-APC's in line on these yet. I'm like >>>>> two >>>>> short at the moment. But we know that 1000Base-T and sync over power + the >>>>> older APC's don't play nice anyway. >>>>> >>>>> On 11/21/2016 1:23 PM, Mathew Howard wrote: >>>>> >>>>> I've had a couple of them where I wasn't getting sync and couldn't >>>>> figure out why... in one case (maybe both... I don't remember off hand), I >>>>> was getting sync to an ePMP, but not to a PMP450i 900mhz AP that were both >>>>> plugged into the same sync injector... I didn't really need sync on the >>>>> 900mhz at the time, so I just switched it to generate it's own timing, and >>>>> I haven't gotten around to trying to figure it out yet, but now I'm >>>>> wondering if it would eventually come up if I left it alone. >>>>> >>>>> On Mon, Nov 21, 2016 at 12:45 PM, Seth Mattinen <se...@rollernet.us> >>>>> wrote: >>>>> >>>>>> On 11/21/16 10:39, ch...@wbmfg.com wrote: >>>>>> >>>>>>> I had all the packet flux gear running for days, plugged in the 450i >>>>>>> and >>>>>>> started trying to figure out why it was not receiving sync. Half >>>>>>> hour >>>>>>> or more later it said it was OK, so the delay had to be Cambium, not >>>>>>> Packetflux. >>>>>>> >>>>>> >>>>>> >>>>>> Check if the packetflux says it has fix and 1PPS is active on the >>>>>> binary tab and that the used pulse count is increasing on the analog tab. >>>>>> >>>>>> ~Seth >>>>>> >>>>> >>>>> >>>>> >>>> >>> >>> >>> -- >>> *Forrest Christian* *CEO**, PacketFlux Technologies, Inc.* >>> Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 >>> forre...@imach.com | http://www.packetflux.com >>> <http://www.linkedin.com/in/fwchristian> >>> <http://facebook.com/packetflux> <http://twitter.com/@packetflux> >>> >>> >> >> >> -- >> If you only see yourself as part of the team but you don't see your team >> as part of yourself you have already failed as part of the team. >> > > -- *Forrest Christian* *CEO**, PacketFlux Technologies, Inc.* Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 forre...@imach.com | http://www.packetflux.com <http://www.linkedin.com/in/fwchristian> <http://facebook.com/packetflux> <http://twitter.com/@packetflux>
