If the orange LED is blinking, then the injector is receiving sync, and
1PPS Active should = 1 (if you have a base unit connected to see it).
Kurt, what software is your 450i running? FWIW, I have a limited number
of 450i APs up, but I have some on SyncBox Junior's (don't get the GPS
data) and the one PowerInjector+Sync at the NOC. All of my 450 and 450i
is running 14.1.2. Perhaps Cambium changed something in 14.2+.
I would verify that the port has sync enabled. Obviously you'd need a
base unit connected. I've plugged radios in backwards on more than one
occasion. Injector upside down for one reason or another, so the radios
ended up 4 thru 1 instead of 1 thru 4 because I wasn't paying attention.
Port 4 is at the end closest to the SyncPipe/sync daisy chain ports.
That's the most obvious issue if you turned off the sync pulse on a port
to run an AirFiber. But if multiple people have had the same problem,
then my theory is bunk.
On 11/24/2016 4:49 PM, Chuck McCown wrote:
I had that same problem last week. Finally started working on its own.
*From:* Kurt Fankhauser
*Sent:* Thursday, November 24, 2016 3:14 PM
*To:* af@afmug.com
*Subject:* Re: [AFMUG] Gigabit power injector + sync
Ok, I just put a new PMP450i on a tower and am running into the exact
same problem the Original Poster had here. I have the Gigabit Power
Injector plus Sync and it is blinking for receiving sync from another
Sync Injector in the same enclosure via the included jumper cable and
the AP is running in Autosync+ Freerun and it is not showing receiving
any sync at all and it is decided to Generate its own Sync. Has been
running for a couple hours now. Will keep checking back here.
On Tue, Nov 22, 2016 at 1:51 PM, That One Guy /sarcasm
<thatoneguyst...@gmail.com> wrote:
all this talk of the new units i opened our box of them, is there
a guide for the 10/100 and gigabit powerinjector jumper settings
per brand?
is it just the same as
http://tickets.packetflux.com/downloads/poeinjectorjumpers.pdf
<http://tickets.packetflux.com/downloads/poeinjectorjumpers.pdf>
only with the pin order backward?
and if a guy put a 3pin connector on the A/B selector, would that
effectively put the two inputs in parallel?
On Tue, Nov 22, 2016 at 11:57 AM, Forrest Christian (List Account)
<li...@packetflux.com> wrote:
Depends on the power circuitry on the airfiber. My guess is
it would be ok.
If you have a base unit, you can actually turn off the sync on
that port and the injector will remember it, so you don't have
to put a base unit in the field with it, just for the
programming. (You'd set the poweron column for the sync row
for that port to '0').
On Tue, Nov 22, 2016 at 8:37 AM, Kurt Fankhauser
<lists.wavel...@gmail.com> wrote:
I just received my first powerinjector + sync today. If I
want to power some Airfibers with these do I need to turn
the sync off for those ports? I don't see a jumper to turn
off sync, is it ok to provider sync on a port with an
Airfiber? Does it hurt anything? It looks to me like the
only way to turn off sync is buy the additional site
monitor base thing to hookup to it and turn it off through
the web interface?
On Mon, Nov 21, 2016 at 2:39 PM, George Skorup
<geo...@cbcast.com> wrote:
I have four 5GHz 450i's running on our office tower
fed from a GigE PowerInjector+Sync. They're running
14.1.2. They received sync shortly after boot, DFS,
etc. BTW, no GigE-APC's in line on these yet. I'm like
two short at the moment. But we know that 1000Base-T
and sync over power + the older APC's don't play nice
anyway.
On 11/21/2016 1:23 PM, Mathew Howard wrote:
I've had a couple of them where I wasn't getting sync
and couldn't figure out why... in one case (maybe
both... I don't remember off hand), I was getting
sync to an ePMP, but not to a PMP450i 900mhz AP that
were both plugged into the same sync injector... I
didn't really need sync on the 900mhz at the time, so
I just switched it to generate it's own timing, and I
haven't gotten around to trying to figure it out yet,
but now I'm wondering if it would eventually come up
if I left it alone.
On Mon, Nov 21, 2016 at 12:45 PM, Seth Mattinen
<se...@rollernet.us> wrote:
On 11/21/16 10:39, ch...@wbmfg.com wrote:
I had all the packet flux gear running for
days, plugged in the 450i and
started trying to figure out why it was not
receiving sync. Half hour
or more later it said it was OK, so the delay
had to be Cambium, not
Packetflux.
Check if the packetflux says it has fix and 1PPS
is active on the binary tab and that the used
pulse count is increasing on the analog tab.
~Seth
--
*Forrest Christian* /CEO//, PacketFlux Technologies, Inc./
Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT
59602
forre...@imach.com | http://www.packetflux.com
<http://www.packetflux.com/>
<http://www.linkedin.com/in/fwchristian>
<http://facebook.com/packetflux> <http://twitter.com/@packetflux>
--
If you only see yourself as part of the team but you don't see
your team as part of yourself you have already failed as part of
the team.
