OK, I did get a report from one customer that my new surge protector design actually fixed this problem with a 450i. Not yet confident enough to state it will fix the problem.
I was testing with my new surge suppressor when I got it to go. From: Forrest Christian (List Account) Sent: Thursday, November 24, 2016 4:31 PM To: af Subject: Re: [AFMUG] Gigabit power injector + sync The 450i is extremely sensitive to any transition noise on the pulse. There's a hidden command in the cambium radios which you may want to try. I'm sending you a email off-list with it in caseyou want to try it. On Thu, Nov 24, 2016 at 3:14 PM, Kurt Fankhauser <lists.wavel...@gmail.com> wrote: Ok, I just put a new PMP450i on a tower and am running into the exact same problem the Original Poster had here. I have the Gigabit Power Injector plus Sync and it is blinking for receiving sync from another Sync Injector in the same enclosure via the included jumper cable and the AP is running in Autosync+ Freerun and it is not showing receiving any sync at all and it is decided to Generate its own Sync. Has been running for a couple hours now. Will keep checking back here. On Tue, Nov 22, 2016 at 1:51 PM, That One Guy /sarcasm <thatoneguyst...@gmail.com> wrote: all this talk of the new units i opened our box of them, is there a guide for the 10/100 and gigabit powerinjector jumper settings per brand? is it just the same as http://tickets.packetflux.com/downloads/poeinjectorjumpers.pdf only with the pin order backward? and if a guy put a 3pin connector on the A/B selector, would that effectively put the two inputs in parallel? On Tue, Nov 22, 2016 at 11:57 AM, Forrest Christian (List Account) <li...@packetflux.com> wrote: Depends on the power circuitry on the airfiber. My guess is it would be ok. If you have a base unit, you can actually turn off the sync on that port and the injector will remember it, so you don't have to put a base unit in the field with it, just for the programming. (You'd set the poweron column for the sync row for that port to '0'). On Tue, Nov 22, 2016 at 8:37 AM, Kurt Fankhauser <lists.wavel...@gmail.com> wrote: I just received my first powerinjector + sync today. If I want to power some Airfibers with these do I need to turn the sync off for those ports? I don't see a jumper to turn off sync, is it ok to provider sync on a port with an Airfiber? Does it hurt anything? It looks to me like the only way to turn off sync is buy the additional site monitor base thing to hookup to it and turn it off through the web interface? On Mon, Nov 21, 2016 at 2:39 PM, George Skorup <geo...@cbcast.com> wrote: I have four 5GHz 450i's running on our office tower fed from a GigE PowerInjector+Sync. They're running 14.1.2. They received sync shortly after boot, DFS, etc. BTW, no GigE-APC's in line on these yet. I'm like two short at the moment. But we know that 1000Base-T and sync over power + the older APC's don't play nice anyway. On 11/21/2016 1:23 PM, Mathew Howard wrote: I've had a couple of them where I wasn't getting sync and couldn't figure out why... in one case (maybe both... I don't remember off hand), I was getting sync to an ePMP, but not to a PMP450i 900mhz AP that were both plugged into the same sync injector... I didn't really need sync on the 900mhz at the time, so I just switched it to generate it's own timing, and I haven't gotten around to trying to figure it out yet, but now I'm wondering if it would eventually come up if I left it alone. On Mon, Nov 21, 2016 at 12:45 PM, Seth Mattinen <se...@rollernet.us> wrote: On 11/21/16 10:39, ch...@wbmfg.com wrote: I had all the packet flux gear running for days, plugged in the 450i and started trying to figure out why it was not receiving sync. Half hour or more later it said it was OK, so the delay had to be Cambium, not Packetflux. Check if the packetflux says it has fix and 1PPS is active on the binary tab and that the used pulse count is increasing on the analog tab. ~Seth -- Forrest Christian CEO, PacketFlux Technologies, Inc. Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 forre...@imach.com | http://www.packetflux.com -- If you only see yourself as part of the team but you don't see your team as part of yourself you have already failed as part of the team. -- Forrest Christian CEO, PacketFlux Technologies, Inc. Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 forre...@imach.com | http://www.packetflux.com