Just tried 14.1.2 and same thing, tomorrow I am going to feed this injector from a different sync pipe instead of pulling sync over the daisy chain and see if that helps. Also if that doesn't I have another NIB powerinjector I can try here.
On Thu, Nov 24, 2016 at 10:33 PM, Ken Hohhof <af...@kwisp.com> wrote: > Hmmmm, I haven’t had any problems with power port sync from a CTM-2 and > 450i. 300 ft cables though. Some of them had 14.2 Build 15 on them and I > downgraded to 14.1.2, power port sync worked both ways. > > > > *From:* Af [mailto:af-boun...@afmug.com] *On Behalf Of *Kurt Fankhauser > *Sent:* Thursday, November 24, 2016 9:09 PM > *To:* af@afmug.com > *Subject:* Re: [AFMUG] Gigabit power injector + sync > > > > I just tried the "debouncepowerport off" command and no change. I may > try downgrading to firmware 14.1.2. > > > > On Thu, Nov 24, 2016 at 10:06 PM, Chuck McCown <ch...@wbmfg.com> wrote: > > OK, I did get a report from one customer that my new surge protector > design actually fixed this problem with a 450i. > > Not yet confident enough to state it will fix the problem. > > > > I was testing with my new surge suppressor when I got it to go. > > > > *From:* Forrest Christian (List Account) > > *Sent:* Thursday, November 24, 2016 4:31 PM > > *To:* af > > *Subject:* Re: [AFMUG] Gigabit power injector + sync > > > > The 450i is extremely sensitive to any transition noise on the pulse. > There's a hidden command in the cambium radios which you may want to try. > I'm sending you a email off-list with it in caseyou want to try it. > > > > > > On Thu, Nov 24, 2016 at 3:14 PM, Kurt Fankhauser <lists.wavel...@gmail.com> > wrote: > > Ok, I just put a new PMP450i on a tower and am running into the exact same > problem the Original Poster had here. I have the Gigabit Power Injector > plus Sync and it is blinking for receiving sync from another Sync Injector > in the same enclosure via the included jumper cable and the AP is running > in Autosync+ Freerun and it is not showing receiving any sync at all and it > is decided to Generate its own Sync. Has been running for a couple hours > now. Will keep checking back here. > > > > On Tue, Nov 22, 2016 at 1:51 PM, That One Guy /sarcasm < > thatoneguyst...@gmail.com> wrote: > > all this talk of the new units i opened our box of them, is there a guide > for the 10/100 and gigabit powerinjector jumper settings per brand? > > is it just the same as http://tickets.packetflux.com/ > downloads/poeinjectorjumpers.pdf only with the pin order backward? > > and if a guy put a 3pin connector on the A/B selector, would that > effectively put the two inputs in parallel? > > > > On Tue, Nov 22, 2016 at 11:57 AM, Forrest Christian (List Account) < > li...@packetflux.com> wrote: > > Depends on the power circuitry on the airfiber. My guess is it would be > ok. > > > > If you have a base unit, you can actually turn off the sync on that port > and the injector will remember it, so you don't have to put a base unit in > the field with it, just for the programming. (You'd set the poweron > column for the sync row for that port to '0'). > > > > On Tue, Nov 22, 2016 at 8:37 AM, Kurt Fankhauser <lists.wavel...@gmail.com> > wrote: > > I just received my first powerinjector + sync today. If I want to power > some Airfibers with these do I need to turn the sync off for those ports? I > don't see a jumper to turn off sync, is it ok to provider sync on a port > with an Airfiber? Does it hurt anything? It looks to me like the only way > to turn off sync is buy the additional site monitor base thing to hookup to > it and turn it off through the web interface? > > > > On Mon, Nov 21, 2016 at 2:39 PM, George Skorup <geo...@cbcast.com> wrote: > > I have four 5GHz 450i's running on our office tower fed from a GigE > PowerInjector+Sync. They're running 14.1.2. They received sync shortly > after boot, DFS, etc. BTW, no GigE-APC's in line on these yet. I'm like two > short at the moment. But we know that 1000Base-T and sync over power + the > older APC's don't play nice anyway. > > On 11/21/2016 1:23 PM, Mathew Howard wrote: > > I've had a couple of them where I wasn't getting sync and couldn't figure > out why... in one case (maybe both... I don't remember off hand), I was > getting sync to an ePMP, but not to a PMP450i 900mhz AP that were both > plugged into the same sync injector... I didn't really need sync on the > 900mhz at the time, so I just switched it to generate it's own timing, and > I haven't gotten around to trying to figure it out yet, but now I'm > wondering if it would eventually come up if I left it alone. > > > > On Mon, Nov 21, 2016 at 12:45 PM, Seth Mattinen <se...@rollernet.us> > wrote: > > On 11/21/16 10:39, ch...@wbmfg.com wrote: > > I had all the packet flux gear running for days, plugged in the 450i and > started trying to figure out why it was not receiving sync. Half hour > or more later it said it was OK, so the delay had to be Cambium, not > Packetflux. > > > > Check if the packetflux says it has fix and 1PPS is active on the binary > tab and that the used pulse count is increasing on the analog tab. > > ~Seth > > > > > > > > > > > > -- > > *Forrest Christian* *CEO, PacketFlux Technologies, Inc.* > > Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 > > forre...@imach.com | http://www.packetflux.com > > <http://www.linkedin.com/in/fwchristian> <http://facebook.com/packetflux> > <http://twitter.com/@packetflux> > > > > > > -- > > If you only see yourself as part of the team but you don't see your team > as part of yourself you have already failed as part of the team. > > > > > > > > -- > > *Forrest Christian* *CEO, PacketFlux Technologies, Inc.* > > Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 > > forre...@imach.com | http://www.packetflux.com > > <http://www.linkedin.com/in/fwchristian> <http://facebook.com/packetflux> > <http://twitter.com/@packetflux> > > >