That's a pretty old document that covers old hardware platforms. I'd refer you to the doc cd 12.4T ios. I've included an excerpt.
http://www.cisco.com/en/US/docs/ios/wan/configuration/guide/wan_mqc_fr_tfshp_ps6441_TSD_Products_Configuration_Guide_Chapter.html#wp1056693 Configuring Class-Based Weighted Fair Queueing Example The following example provides a sample configuration for CBWFQ with FRTS: class-map voice match ip dscp ef policy-map llq class voice priority 32 policy-map shape-policy-map class class-default shape average 64000 shape adaptive 32000 service-policy llq map-class frame-relay shape-map-class service-policy output shape-policy-map interface serial 0/0 encapsulation frame-relay interface serial 0/0.1 point-to-point ip address 192.168.1.1 255.255.255.0 frame-relay interface-dlci 100 class shape-map-class ________________________________ From: Imran Ali <[email protected]> To: Rob Pool <[email protected]> Cc: "[email protected]" <[email protected]> Sent: Tuesday, September 4, 2012 6:07 PM Subject: Re: [OSL | CCIE_RS] wrong solution ?? Cisco 7500 Series Cisco 7200, 2600/3600 Series, and Other Platforms Main Interface Configure a service policy on the main interface Supported only if Frame Relay TS is not enabled and the queueing mechanisms apply to a single interface pipe. Subinterface Configure a servicepolicy on the subinterface. Configure a service policy within a Frame Relay map-class and enable per-VC queueing with the frame-relay traffic-shaping command. You can apply the map-class to the subinterface. VC Level Configure a service-policy within a Frame Relay map-class and enable per-VC queueing with the frame-relay traffic-shaping command. You can apply the map-class to the VC. w.r.t VC Level .. it does requires FRTS . check the link in previous mail. i guess ONLY under main interface we can apply CBWFQ . But not on a PVC or a sub-interface. thanks On Wed, Sep 5, 2012 at 12:49 AM, Rob Pool <[email protected]> wrote: I believe you may be mistaken. I don't believe there is any requirement to configure FRTS on the interface to use CBWFQ under a map-class. > >Sent from my iPhone > > >On Sep 4, 2012, at 5:27 PM, Imran Ali <[email protected]> wrote: > >> guys either my understanding is wrong ..or could be task. >> >> i hope you all understood my query . >> >> On Tue, Sep 4, 2012 at 8:53 AM, Imran Ali <[email protected]> wrote: >> >>> Hi all, >>> >>> i am in VOL 2 LAB 15 . below is the task. >>> >>> configure CBWFQ on R5 interface S0/1/0.2 and PVC between R5 and R6 . >>> The following packets routerd to MPLS core must be allocated a bandwidth . >>> >>> IPP 5 should be allocated 30 % of bandwidth >>> IPP 4 should be allocated 20 % of bandwidth >>> >>> Ensure the policy map is applied to pvc and not to subinterface. >>> >>> >>> Question : in soluiton we have CBWFQ policy map applied under a map-class >>> for that pvc . >>> >>> however we know that when enabling CBWFQ on a pvc we MUST have FRTS >>> enabled first . their is no FRTS in solution . >>> >>> from cco : >>> Configure a service-policy within a Frame Relay map-class and enable >>> per-VC queueing with the *frame-relay traffic-shaping* command. You can > >>> apply the map-class to the VC. >>> >>> >>> http://www.cisco.com/en/US/tech/tk543/tk545/technologies_tech_note09186a008009489a.shtml >>> >>> >>> Any ideas guys ? >>> >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> Are you a CCNP or CCIE and looking for a job? Check out >> www.PlatinumPlacement.com >> >> http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
