Sorry, I meant P99SE, not P98SE. ----- Original Message ----- From: "Robert Gillatt" <[EMAIL PROTECTED]> To: "'Jeff Condit'" <[EMAIL PROTECTED]>; "'Protel EDA Discussion List'" <[email protected]> Sent: Monday, September 10, 2007 2:23 PM Subject: RE: [PEDA] DXP PCB -> 99SE
> > I thought P99SE was just P98SE with a few patches, you are saying that > they > are different beasts and that DXP is closer to 98 than it is to 99. > Our DXP, I think, is something like 6.3. The "about" menu tells me it is > DXP2004. I'll have to check with the systems guy to be sure. > > Thanks again, > Rob > > > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > On > Behalf Of Jeff Condit > Sent: 10 September 2007 21:57 > To: Protel EDA Discussion List > Subject: Re: [PEDA] DXP PCB -> 99SE > > > Bob, > > I have Altium Designer 6.7 up and running. In a pinch I could try loading > your DXP design into AD6.7 and than save it as file version 4. However, I > haven't done this a lot and so cannot vouch that everything would make it > through intact. You'd still have to look it over in P99SE. I think it > would be better if you could go directly from DXP to P98SE as they are > much > more closely related. > > ----- Original Message ----- > From: "Steve Smith" <[EMAIL PROTECTED]> > To: "Jeff Condit" <[EMAIL PROTECTED]>; "Protel EDA Discussion List" > <[email protected]> > Sent: Monday, September 10, 2007 9:43 AM > Subject: RE: [PEDA] DXP PCB -> 99SE > > >> Good luck with that. The primary reason we upgraded to DXP from 99SE >> was that we had an outside source do a design for us in DXP and when >> we brought them back into 99SE we had major problems with the file >> being readable by 99SE. It literally took many multiple attempts to >> open the file in 99SE, if it would open at all. >> >> >> Regards, >> Steve Smith >> Product Engineer >> Staco Energy Products Co. >> Web Site: www.stacoenergy.com >> & www.stacopower.com >> >> DISCLAIMER AND/OR CONFIDENTIALITY NOTICE: >> This message, including any attached materials, is intended solely for >> the use of the individual or entity to whom it is addressed and may >> contain information that is privileged, confidential, and exempt from >> disclosure under applicable law. If the reader of this electronic mail >> transmission is not the intended recipient, you are hereby notified >> that any dissemination, distribution, or copying of this communication >> is strictly prohibited. If you have received this communication in >> error, please e-mail or call Staco Energy Products Co. at (937) >> 253-1191. Thank you for your cooperation. >> >> >> >> -----Original Message----- >> From: [EMAIL PROTECTED] >> [mailto:[EMAIL PROTECTED] >> On Behalf Of Jeff Condit >> Sent: Monday, September 10, 2007 11:11 AM >> To: [EMAIL PROTECTED]; Protel EDA Discussion List >> Subject: Re: [PEDA] DXP PCB -> 99SE >> >> Robert, >> >> I don't have DXP up right now but believe P99SE files are version 4. >> Can you try doing a Save-As to version 4? >> >> ----- Original Message ----- >> From: "Robert Gillatt" <[EMAIL PROTECTED]> >> To: "'Protel EDA Discussion List'" <[email protected]> >> Sent: Monday, September 10, 2007 7:40 AM >> Subject: [PEDA] DXP PCB -> 99SE >> >> >>> Hi, >>> Does anyone know if I can save DXP .pcbdoc files in a format that >> 99SE >>> will >>> recognize. I know, I am a lazy man, but it might save me trying out >> all >>> the >>> variations on the Save As menu. >>> >>> Thanks >>> Rob >>> >>> R`theta Electronics >>> >>> <mailto:[EMAIL PROTECTED]> >>> >> >> >> >> -- >> No virus found in this incoming message. >> Checked by AVG. >> Version: 7.5.485 / Virus Database: 269.13.13/998 - Release Date: >> 9/10/2007 > >> 8:48 AM >> >> > > > > ____________________________________________________________ > You are subscribed to the PEDA discussion forum > > To Post messages: > mailto:[email protected] > > Unsubscribe and Other Options: > http://techservinc.com/mailman/listinfo/peda_techservinc.com > > Browse or Search Old Archives (2001-2004): > http://www.mail-archive.com/[EMAIL PROTECTED] > > Browse or Search Current Archives (2004-Current): > http://www.mail-archive.com/[email protected] > > > > > -- > No virus found in this incoming message. > Checked by AVG. > Version: 7.5.485 / Virus Database: 269.13.13/998 - Release Date: 9/10/2007 > 8:48 AM > > ____________________________________________________________ You are subscribed to the PEDA discussion forum To Post messages: mailto:[email protected] Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[EMAIL PROTECTED] Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected]
