Re: [Flexradio] WSPR CAT Config Question

@flex-radio.biz Subject: [Flexradio] WSPR CAT Config Question I'm configuring WSPR's CAT commands. The "Rig Number" only shows the Flex 1000. Not sure what other radio to choose? -- *Best 73 de WA2SQQ Elmwood Park, NJ "The only dumb questio

Re: [Flexradio] WSPR CAT Config Question

Also be sure to use a com port less than 10 and set Power SDR to id as a TS-2000 -Original Message- From: Bob Kay Sent: Tuesday, February 26, 2013 13:11 To: FlexRadio@flex-radio.biz Subject: [Flexradio] WSPR CAT Config Question I'm configuring WSPR's CAT commands. The &

Re: [Flexradio] WSPR CAT Config Question

Try using the Kenwood TS-2000 -Original Message- From: Bob Kay Sent: Tuesday, February 26, 2013 13:11 To: FlexRadio@flex-radio.biz Subject: [Flexradio] WSPR CAT Config Question I'm configuring WSPR's CAT commands. The "Rig Number" only shows the Flex 1000. Not sure

Re: [Flexradio] WSPR CAT Config Question

@flex-radio.biz Subject: [Flexradio] WSPR CAT Config Question I'm configuring WSPR's CAT commands. The "Rig Number" only shows the Flex 1000. Not sure what other radio to choose? -- *Best 73 de WA2SQQ Elmwood Park, NJ "The only dumb questio

[Flexradio] WSPR and PSDr

Is anyone who is using WSPR having problems with it crashing after about 20 minutes? It works fine, then in a TX cycle it will just crash. This is on a Flex 5000 Win 7 64. I don't think that this is a Flex issue at all, but I thought I would through it out there. Mike va3mw

[Flexradio] WSPR

Can I get WSPR to work with my Flex 5000? Burt ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Bas

[Flexradio] WSPR CAT Control

: FlexRadio@flex-radio.biz Subject: [Flexradio] WSPR CAT Control - Flex 3000 and PSDR 2.3.5 Sorry if this is a repeat of earlier postings. I have searched the past emails I have and found some on this topic but did not find a clear resolution. May have deleted it at some time. But, my problem is with WSPR

Re: [Flexradio] WSPR CAT Control - Flex 3000 and PSDR 2.3.5

several other digital mode programs. Hope this helps? Emory WM3M -Original Message- From: TM Sent: Thursday, May 10, 2012 10:43 PM To: FlexRadio@flex-radio.biz Subject: [Flexradio] WSPR CAT Control - Flex 3000 and PSDR 2.3.5 Sorry if this is a repeat of earlier postings. I have

[Flexradio] WSPR CAT Control - Flex 3000 and PSDR 2.3.5

Sorry if this is a repeat of earlier postings. I have searched the past emails I have and found some on this topic but did not find a clear resolution. May have deleted it at some time. But, my problem is with WSPR. I had it working like a champ with my old computer and earlier PSDR. Just swit

Re: [Flexradio] WSPR and Cat Control - solved

On Fri, Mar 16, 2012 at 7:26 AM, Michael Walker wrote: > I also set Joe, the author, an email so that at some point might want to > add that limitation to the software so that you can't pick port 9 and > above. > I told Joe Taylor about this at least a year ago. -- Brian Lloyd, WB6RQN/J79BPL 31

Re: [Flexradio] WSPR and CAT and first time use

Hi Brian That is interesting. Note for other first time users that don't read the manual fully.. all the time, like me! If you are expecting the WSPR waterfall to start 'right away', it doesn't. WSPR does everything based on being at the top of every even minute. So, the first time you start u

[Flexradio] WSPR and Cat Control - solved

I also set Joe, the author, an email so that at some point might want to add that limitation to the software so that you can't pick port 9 and above. Nice collaboration. Thanks all. Mike va3mw On Fri, Mar 16, 2012 at 10:08 AM, Tony Estep wrote: > On Thu, Mar 15, 2012 at 9:50 PM, Brian Lloyd

Re: [Flexradio] WSPR and CAT

On Thu, Mar 15, 2012 at 12:06 PM, Tony Estep wrote: > On Thu, Mar 15, 2012 at 1:49 PM, Al K0VM wrote: > > ...Although WSPR shows all available COM ports, rigctl only supports > COM1 thru > > COM8... > In my tests it works with com1-com9. I suppose it could have changed but the version of WSPR I

Re: [Flexradio] WSPR and CAT

And, I have updated the wiki http://flexradiowiki.com/frsradoiowiki/index.php?title=WSPR Mike va3mw On Thu, Mar 15, 2012 at 4:00 PM, Michael Walker wrote: > I just tested this and it worked. > > 2.3.5 Psdr > 1.03 VSP Manager > TS2000 emulation on PSDR > Com port 4 > > I have to test and see if

Re: [Flexradio] WSPR and CAT

I just tested this and it worked. 2.3.5 Psdr 1.03 VSP Manager TS2000 emulation on PSDR Com port 4 I have to test and see if I can get it to work with DDUTIL. It 'should'. This boils down to the fact that the PTT line can be up to 15, but the Rig Control can only go up to Com 8. The Wiki should

Re: [Flexradio] WSPR and CAT

Ah, that makes sense now. I just hand not had a chance to get to the source code. And, that is the reason for the IO error. Mike va3mw On Thu, Mar 15, 2012 at 3:06 PM, Tony Estep wrote: > On Thu, Mar 15, 2012 at 1:49 PM, Al K0VM wrote: > > ...Although WSPR shows all available COM ports, rig

[Flexradio] WSPR and CAT

On Thu, Mar 15, 2012 at 1:49 PM, Al K0VM wrote: > ...Although WSPR shows all available COM ports, rigctl only supports COM1 thru > COM8... Very helpful, Al. I gather that you must have dug this out of the source code -- great work! Like many others, I made my port combos COM3->COM13, etc

Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500

Here is the thing we need to determine the "Fiq" We know we have the direct conversion receiver required. Quoting the WSPR I/Q set up instructions" "Depending on how you have wired your SoftRock, you may or may not need to check Reverse Rx I,Q or Reverse Tx I,Q. Mine does not need these boxes ch

Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500

On Tue, Sep 13, 2011 at 1:13 PM, Al K0VM wrote: > FWIW I have been running WSPR with the F1500 in 17m for days at a time and > have never seen this problem with the 1500. Not with WSPR or any other > time.. ( I have seen it with the SDR1000 in the past, so I think I know > what the symptoms a

Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500

? ( PSDR 2.2.2, VAC 4.10(p) & WSPR 2.11 ) AL, K0VM On 9/13/2011 12:00 PM, flexradio-requ...@flex-radio.biz wrote: Date: Mon, 12 Sep 2011 22:46:45 -0700 From: Brian Lloyd To: Steven Hess Cc:FlexRadio@flex-radio.biz Subject: Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500 Messag

Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500

On Tue, Sep 13, 2011 at 12:30 AM, wrote: > Hello, > > i use my Flex1500 very often many hours with WSPR and have no problems. I > have the newest PSDR version in use. > Are you using the frequency-hopping version of WSPR or are you using the regular release version that just stays on one band?

Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500

Good to know .Thanks On Tue, Sep 13, 2011 at 2:20 AM, wrote: > I checked it an it is actual the latest PowerSDR_v2.2.2 . > > Regards > Mathias > > 2011/9/13 Steven Hess > >> Markru what version of PowerSDR are you using? >> >> On Tue, Sep 13, 2011 at 1:22 AM, Steven Hess wrote: >> >> > Seems t

Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500

I checked it an it is actual the latest PowerSDR_v2.2.2 . Regards Mathias 2011/9/13 Steven Hess > Markru what version of PowerSDR are you using? > > On Tue, Sep 13, 2011 at 1:22 AM, Steven Hess wrote: > > > Seems to not be an issue any more then. > > > > > > On Tue, Sep 13, 2011 at 12:30 AM,

Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500

Markru what version of PowerSDR are you using? On Tue, Sep 13, 2011 at 1:22 AM, Steven Hess wrote: > Seems to not be an issue any more then. > > > On Tue, Sep 13, 2011 at 12:30 AM, wrote: > >> Hello, >> >> i use my Flex1500 very often many hours with WSPR and have no problems. I >> have the ne

Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500

Hello, i use my Flex1500 very often many hours with WSPR and have no problems. I have the newest PSDR version in use. Regards Mathias 2011/9/13 Brian Lloyd > On Mon, Sep 12, 2011 at 9:25 PM, Steven Hess wrote: > > > Is there still an issue with the Flex-1500 losing WBIR after about 20 > > mi

Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500

On Mon, Sep 12, 2011 at 9:25 PM, Steven Hess wrote: > Is there still an issue with the Flex-1500 losing WBIR after about 20 > minutes of WSPR? > Yes. I am suffering with that right now. I recently asked Flex if there was progress on fixing this problem but have not yet heard back. -- Brian Llo

Re: [Flexradio] WSPR Setup on PowerSDR and FLEX-1500

Is there still an issue with the Flex-1500 losing WBIR after about 20 minutes of WSPR? On Mon, Sep 12, 2011 at 9:06 PM, Kabulldust wrote: > G'dday Steven, > > I've just resurrected my FLEX-1500 that I may take with me to Nairobi and > Mogadishu so that I have a suitable radio to do WSPR from Mog

Re: [Flexradio] WSPR or JT-65 with my 1500?

Michael: The FLEX-1500 won't be hurt by normal digital mode operation even at full output. It's been tested to support this duty cycle. FYI, I've run WSPR quite a bit with the FLEX-1500. I actually prefer going to the LOW end of the power range. I've run paths at 56mW (Power=1) and at +3dbm (F

Re: [Flexradio] WSPR or JT-65 with my 1500?

Michael Check out this page from the flexradiowiki.com http://www.flexradiowiki.com/frsradoiowiki/index.php?title=WSPR 73 Neal On Sun, May 29, 2011 at 7:29 PM, Michael Tondee wrote: > Sorry for the slight off topic post but today

[Flexradio] WSPR or JT-65 with my 1500?

Sorry for the slight off topic post but today I've been a little bored so I decided to start looking into these modes that I've been meaning to get around to. Which is the best for unattended or semi unattended operation while I'm puttering around the shack doing other things? Is there a handy

Re: [Flexradio] wspr

On Thu, Mar 10, 2011 at 1:48 AM, Nick Pugh K5QXJ wrote: > Hi all > > I am new to flex. I am trying to get my 5000 working with WSPR via VAC. I > have the tx working . I see waterfall display on the rx but can not decode > it. I have set the rx from +10 to -10 with no joy. Suggestions?? > I'm ass

Re: [Flexradio] wspr

Nick What OS are you running on your computer ? Dave -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Nick Pugh K5QXJ Sent: Thursday, March 10, 2011 2:49 AM To: flexradio@flex-radio.biz Subject: [Flexradio] wspr Hi all I

[Flexradio] wspr

Hi all I am new to flex. I am trying to get my 5000 working with WSPR via VAC. I have the tx working . I see waterfall display on the rx but can not decode it. I have set the rx from +10 to -10 with no joy. Suggestions?? Thanks Nickk5qxj Office 337 593 8700 Cell 337 258 25

Re: [Flexradio] WSPR

On Mon, Jan 17, 2011 at 9:50 AM, Richard Lawn wrote: > Anyone out there using WSPR with their 5K? Any suggestions on setup or is > it > obvious, although nothing is obvious on a Windows PC to the long-time Mac > user :)? I noticed that in the list of radios supported by WSPR only > includes the F

Re: [Flexradio] WSPR

Original Message Subject:Re: [Flexradio] WSPR Date: Mon, 17 Jan 2011 20:41:28 -0500 From: Bill Bordy, NJ1H To: Richard Lawn I have used my Flex 5K on WSPR without any problems running it several times from before dusk to after sunrise on 80M without any

Re: [Flexradio] WSPR

On 1/17/2011 10:50 AM, Richard Lawn wrote: Anyone out there using WSPR with their 5K? Any suggestions on setup or is it obvious, although nothing is obvious on a Windows PC to the long-time Mac user :)? I noticed that in the list of radios supported by WSPR only includes the Flex 1K. I don't have

Re: [Flexradio] WSPR

FYI, I've run WSPR several times overnight with no blue-screens. OTOH, my PC was running PSDR today and the screen froze, and now it won't boot anymore, so maybe I used up all the karma. Sigh. /Jack On Mon, 2011-01-17 at 11:11 -0800, Jerry Gardner wrote: > On Mon, Jan 17, 2011 at 9:50 AM, Richa

Re: [Flexradio] WSPR

On Mon, Jan 17, 2011 at 9:50 AM, Richard Lawn wrote: > Anyone out there using WSPR with their 5K? Any suggestions on setup or is > it > obvious, although nothing is obvious on a Windows PC to the long-time Mac > user :)? I noticed that in the list of radios supported by WSPR only > includes the F

Re: [Flexradio] WSPR

I've used WSPR on my Flex-3K., should be the same on 5K. It's pretty much the same as using any other digital mode 3rd party software through VAC and VSPMgr. If you haven't done digital at all yet, I'd recommend setting up something else - PSK or RTTY first, since it will me much faster to see if

[Flexradio] WSPR

Anyone out there using WSPR with their 5K? Any suggestions on setup or is it obvious, although nothing is obvious on a Windows PC to the long-time Mac user :)? I noticed that in the list of radios supported by WSPR only includes the Flex 1K. Rick W2JAZ _

Re: [Flexradio] WSPR and 1500

On Tue, Sep 21, 2010 at 3:11 PM, Ted Leonard wrote: > Hi Folks, > > A couple of days ago I met with success getting Fldigi to work with my 1500 > thanks to a great article by Brian Lloyd WB6RQN on the Fldigi wiki site. > http://fedorahosted.org/fldigi/wiki/Documentation/HOWTO/PowerSDR > I used p

[Flexradio] WSPR and 1500

Hi Folks, A couple of days ago I met with success getting Fldigi to work with my 1500 thanks to a great article by Brian Lloyd WB6RQN on the Fldigi wiki site. http://fedorahosted.org/fldigi/wiki/Documentation/HOWTO/PowerSDR I used port 6 and 7 with 7 for Cat control in fldigi. He also shows t

[Flexradio] WSPR Experience

TNx to the flex reflector I just started WSPR with DDutil and PowerSDR on my Flex500a and in the first trasmission on 40 meters 1 watt I was captured fron Australia and States ... Like to share with you 73 de IK4GBU - Valerio ___ FlexRadio System

[Flexradio] WSPR experience

I wrote a week or so ago about problems I was having with WSPR and Mack, WB4MAK, replied with his settings. First, my original problem was that WSPR could not set the frequency and that PTT via CAT was somewhat unreliable. The main symptom was that every time WSPR tried to set the frequency, key,

[Flexradio] WSPR ver. 2.0 released

This software is amazing, you will be surprised on what you could hear. cheers Paul -- Me, Myself and I accepts no liability for the content of this E-Mail, or for the consequences of any actions taken on the basis of the information provided, unless that information is subsequently confirmed

Re: [Flexradio] WSPR ver. 2.0 released, improved set-up with PowerSDR now

> > WSPR is now much easier set up for use with PowerSDR, as it now > includes > direct PTT via CAT with PowerSDR, and also the audio set up now > recognizes > the VAC cables assignments. > I realize this is the WSPR support list, but... Your post intrigued me enough to get me to download and

[Flexradio] WSPR ver. 2.0 released, improved set-up with PowerSDR now

Just to let those interested in WSPR by K1JT know, a new version 2.0 was just released a few days ago. go to website www.wsprnet.org for full information and download information. WSPR is now much easier set up for use with PowerSDR, as it now includes direct PTT via CAT with PowerSDR, and a

Re: [Flexradio] WSPR

Scott, Yes, I've been running WSPR on the SDR-1000 all along. I'm using VAC at 48000 sample rate on the PowerSDR side. My PowerSDS Rx gain is set to -18dB; I determined that value by setting the level which generally gives about a "0dB" baseline in WSJT JT65A mode, and it has worked fine.

Re: [Flexradio] WSPR

Don't forget to keep your system clock synchronised to a time server. 73 Eddy ON5UQ. - Original Message - From: "KQ8RP" <[EMAIL PROTECTED]> To: Sent: Saturday, April 26, 2008 5:41 PM Subject: [Flexradio] WSPR > Does anyone have WSPR set up on the SDR1000 runni

Re: [Flexradio] WSPR

It is alpha software and it keeps blowing up on my PC. The configuration is the same for WSJT. -Tim -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of KQ8RP Sent: Saturday, April 26, 2008 11:42 AM To: flexradio@flex-radio.biz Subject: [Flexradio] WSPR

[Flexradio] WSPR

Does anyone have WSPR set up on the SDR1000 running? I can't seem to get it working. Any config on WSPR and VAC that you can share would be helpful. Thanks Scott KQ8RP ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.b