I did only the one mod which was .
9.6v to a 10k resistor to the base, emitter went to ground, collector to the
controller. This mod was on the better duplexing for a micor station on
repeater builder site.
Nick
w7nik
775-626-7605
Web site-- http://geocities.com/w7...@sbcglobal.net/
When
I might have to add 12 volts into a 10k to the collector. Thanks to a friend in
our club , he suggested to use the NHRC cas inverter . I did not want to that
with out direction. I don't smoke anymore ::))
Nick
w7nik
775-626-7605
Web site-- http://geocities.com/w7...@sbcglobal.net/
When all
Thanks Kevin , That mobile note threw me off . I did see that mod. I will give
that a try thanks again. Your mods are very helpful.
Nick
w7nik
775-626-7605
Web site-- http://geocities.com/w7...@sbcglobal.net/
When all else fails . Amateur Radio.
From
I have a micor Station , I did the mod for the cos on the audio sq board . I
have 9.6v no signal , with signal 0 volts. I need o volts no signal and 5 volts
or more for signal. I did the invert logic mod , with the 10 k npn 2n
transiter not enough voltage less than 1 volt. Any Ideas ?
I have some micor repeaters with the Factory encode boards. I would like to
make them half duplex. I can not get the board to transmit pl encode on ptt/mic
or local. I see the pl on the scope on the exciter but not out the audio path.
Any ideas?? Good thing i have manual or i would be lost. I
--- In Repeater-Builder@yahoogroups.com, Nick w7...@... wrote:
I have some micor repeaters with the Factory encode boards. I would like to
make them half duplex. I can not get the board to transmit pl encode on
ptt/mic or local. I see the pl on the scope on the exciter but not out
I am looking for a completed manual for Micor UHF Station.
Would you have any with a price to shipped to reno
68p81025E50 service manual
68p81025E60 control and applications
I have a GE mstr II rack repeater. Uhf version. I am installing an
rc210 controller. I have all the cards out accept the 10 v regulator
card plus I have the guard tone board and the encode board installed.
These are original boards. I have found receive flat audio, transmit
audio, PTT, and cos.
-Builder@yahoogroups.com, Nick [EMAIL PROTECTED] wrote:
I have a GE mstr II rack repeater. Uhf version. I am installing an
rc210 controller. I have all the cards out accept the 10 v regulator
card plus I have the guard tone board and the encode board
installed.
These are original boards. I have
upgrade mode and use the input/output for a
short lived packet
session.
Let me know if you find a solution.
Nick
Tom wrote:
Anyone have any experience using one to remotely
program or do
software changes on controllers via an RF link of
some kind?
What type was successful?
Thanks
NB2A
upgrade mode and use the input/output for a
short lived packet
session.
Let me know if you find a solution.
Nick
Tom wrote:
Anyone have any experience using one to remotely
program or do
software changes on controllers via an RF link of
some kind?
What type was successful?
Thanks
NB2A
. . Any helpful suggestions on common failure modes or anctidotes on ones
you have repaired would be welcome! I've got a lot of things to use this on to
get my 900 Mhz repeater up and going.
Thanks, Nick
WB7PEK
on this. I
am willing to pay for copying and mail charges, just buy outright, or easier
yet, any pdf scans to save a tree.
Thanks in advance,
Nick
WB7PEK
Finding fabulous fares is fun.
Let Yahoo
to the repeater and digitally controlled rotator. This
is also an interesting concept.
Nick
- Original Message
From: Jack Taylor [EMAIL PROTECTED]
To: Repeater-Builder@yahoogroups.com
Sent: Thursday, February 22, 2007 3:46:48 PM
Subject: Re: [Repeater-Builder] OT- Activity Level On Ham
;
Message: 2
Date: Fri, 18 Nov 2005 9:17:54 -0500
From: [EMAIL PROTECTED]
Subject: Re: wiring a link radio
Nick,
This is one option that works for any radio.
http://www.repeater-builder.com
I'm also looking for a UHF Micor. Anyone?
forfun wrote:
Hello group...
I am looking for a 100watt uhf mobile micor in good working order.
Please reply off list to my e-mail
va3kmc Keith
Yahoo! Groups Links
Yahoo! Groups Links
* To visit your
Rich Garcia wrote:
Jan has been very troublesome in the 25+ years I have been a ham, you hear
of a lot of complaints.
Yup. They indicated my crystal was shipped, however I never received.
Next time I'm not using USPS Parcel!
Yahoo! Groups Links
* To visit your group on the web, go to:
Hi Folks,
I'm considering purchasing a 45A IOTA Switched Power
supply to power a UHF Micor and am concerned about
switch PS noise.
Has anyone tried these supplies with UHF radios? Is
noise experienced?
Insight greatly appreciated. Thanks.
--
Nick KB1GZN Boston, MA
Yahoo! Groups Links
I'm looking for two pairs for low band channel elements. Does anyone
have any or know where to find?
Thanks
Nick, KB1GZN Boston, MA
Yahoo! Groups Links
* To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
* To unsubscribe from this group, send
boards available on Ebay, however I haven't
seen encode boards.
Thanks,
Nick KB1GZN Boston, MA
Yahoo! Groups Links
* To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
* To unsubscribe from this group, send an email to:
[EMAIL PROTECTED]
* Your use
Does anyone have this in PDF format? I need to retune a UHF Micor
Mobile so it can be used as a repeater.
Thanks
Yahoo! Groups Links
* To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
* To unsubscribe from this group, send an email to:
Mike Morris WA6ILQ wrote:
--- Nick Papadonis [EMAIL PROTECTED] wrote:
Is anyone aware of either hardware or software
components to decode PL
tone, DTMF and CTCSS? Open source software is
preferred.
There was a program called WinTone that would do this.
Not sure where to find a copy
and xcat interface).
Insight appreciated.
Thanks,
Nick KB1GZN Boston, MA
Yahoo! Groups Links
* To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
* To unsubscribe from this group, send an email to:
[EMAIL PROTECTED]
* Your use of Yahoo! Groups
Do you have any recommendations on 70cm duplexers capable of 100W?
Thanks
Kevin Custer wrote:
Dr. Ron Johnson wrote:
We just got approved for a repeater on 2 meters. I need a duplexer.
Anybody got one laying around? Also, what do you all think about the
mobile duplexers and low power
24 matches
Mail list logo
