Yes the Software configuration does indeed say that. But A while back
I ran into a problem that indicated otherwise. I guess I just need to
run a test case in the lab to verify it. So for test questions go with
what the book says.
Brian
On 6/29/2011 8:12 PM, adam compton wrote:
Not accor
Hi All,
I have CUE in SRST mode and it works fine, but when i bring back CUCM i dont
see the CTI Route point and CTI ports getting registered at all unless i reboot
the CUE module.
Is this the way it normally behaves or am i unaware of some configuration to
fix this behaviour.
Also can you pl
Adam,
It sounds conflicting, but you have to understand what it's asking, it most
like doesn't mean to use priority queue out.
You have to make sure it's asking for priority queue out.
> From: ccie_voice-requ...@onlinestudylist.com
> Subject: CCIE_Voice Digest, Vol 64, Issue 232
> To: ccie
Not according to the 3750 QOS example guide. It says if you have
Priority-queue out on an interface, SRR is ignored for the priority queue,
and it is serviced until empty.
On Wed, Jun 29, 2011 at 8:05 PM, Brian Mahler wrote:
> **
> My understanding is the the SRR Shaped command still applies to
Did you check the blue print?
https://learningnetwork.cisco.com/docs/DOC-5292
On Wed, Jun 29, 2011 at 5:30 PM, Divin Mathew John wrote:
>
>
> ___
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
> A
This a lab so yes it is, I do don't remember why I did it , but
normally I would not do that.
Brian
On 6/29/2011 7:43 PM, Bill Lake wrote:
do you really have your voice and access vlan the same id of 201?
On Wed, Jun 29, 2011 at 6:56 PM, Brian Mahler wrote:
Here ia a command on the switch
The MQC commands (class-maps, policy-maps, etc) can only be applied on
ingress with switches. Although, you can also rate limit in the egress
direction as well, just not using the MQC . To rate limit in the egress
direction you can use the following commands:
Lets say you had a 1Gb/s link o
do you really have your voice and access vlan the same id of 201?
On Wed, Jun 29, 2011 at 6:56 PM, Brian Mahler wrote:
> Here ia a command on the switch that will show you packet counts for each
> DSCP/COS values ( for both inbound and outbound traffic (you wont need to
> use port spanning and a
3750
On Wed, Jun 29, 2011 at 4:30 PM, Divin Mathew John wrote:
>
>
> ___
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
> Are you a CCNP or CCIE and looking for a job? Check out
> www.PlatinumPlace
Neither. 3750 and ESW modules
On Wed, Jun 29, 2011 at 6:30 PM, Divin Mathew John wrote:
>
>
> ___
> For more information regarding industry leading CCIE Lab training, please
> visit www.ipexpert.com
>
> Are you a CCNP or CCIE and looking for a job? Che
My understanding is the the SRR Shaped command still applies to the
queue even though Priority Queue out is applied to the interface. It
prevents the Priority queue from starving out the other queues (that are
shared). Acts similiar to the Policy-map "Priority" command on the
routers. The S
Here ia a command on the switch that will show you packet counts for
each DSCP/COS values ( for both inbound and outbound traffic (you wont
need to use port spanning and a sniffer). This works on the 2960, 2970
, 3560, 3750 switches. This is a LOT faster. I've noticed I had to
modify the wi
Adam,
I have had the same exact question. As far as I know, you could
only assign bandwidth to inbound priority queue. If someone sheds a light on
this, it would be appreciated.
Thank,
Emin
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylis
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
Congratulationsss
Dual CCIE , woww
I like this :)
Best Regards ,
Moataz Mamdouh Tolba
CCIE # 26129 (Voice)
-Original Message-
From: George Goglidze
Sender: ccie_voice-boun...@onlinestudylist.com
Date: Wed, 29 Jun 2011 14:44:21
To: CCIE Voice online groupstudy
Subject: [O
Well done George and thanks for all your help!
On Wed, Jun 29, 2011 at 2:44 PM, George Goglidze wrote:
> Hi all,
>
> As the subject suggests, it's official, I'm dual CCIE #19926 R&S and Voice
> starting yesterday.
>
> Finally, it's a relief, no more studying late, spending weekends on a
> comput
I've had practice questions that state to guarantee traffic for the priority
queue, but it also says shape queue 1 to 30%. As I would normally
understand it, to enable the priority queue you need the following command
on a port:
priority-queue out
If you use this command SRR shaping and sharing
Thanks a lot guys,
Jeff, I'm not sure how much I can say regarding this, but it wasn't a
hardware failure, and I sat the whole exam, and got the free voucher only
after opening a ticket through certsupport community.
I don't know if I can say exactly what the problem was, so you have to
excuse me
Excellent George!!! Shall we celebrate with a Bacon & Maple Sundae?
Congratulations :-)
On Wed, Jun 29, 2011 at 1:14 PM, Ki Wi wrote:
> What kind of technical problem you faced and managed to get a voucher?
>
> My router rebooted halfway due to traceback consider technical problem ?
> Haha... I
On Wed, Jun 29, 2011 at 9:44 AM, George Goglidze wrote:
>
>
> By the way, I made it technically on my first attempt. Well, I payed once
> only, although I went to exam 3 times.
> 1st time, technical problems, Cisco gave me free retake voucher, 2nd time,
> again technical problems, again free vouch
Hi George,
Congrats... You're the MAN
Julien
2011/6/29 George Goglidze
> Hi all,
>
> As the subject suggests, it's official, I'm dual CCIE #19926 R&S and Voice
> starting yesterday.
>
> Finally, it's a relief, no more studying late, spending weekends on a
> computer, making calls, my neig
What kind of technical problem you faced and managed to get a voucher?
My router rebooted halfway due to traceback consider technical problem ?
Haha... I didn't get any extra time for it and even spend extra time to run
back and fore to inform the proctor =[ bad luck
Sent from my iPhone
Pls p
Congrats!
On Wed, Jun 29, 2011 at 9:44 AM, George Goglidze wrote:
> Hi all,
>
> As the subject suggests, it's official, I'm dual CCIE #19926 R&S and Voice
> starting yesterday.
>
> Finally, it's a relief, no more studying late, spending weekends on a
> computer, making calls, my neighbours t
LinkedIn
Fatai Adekunle requested to add you as a connection on LinkedIn:
--
Erwan,
I'd like to add you to my professional network on LinkedIn.
- Fatai
Accept invitation from Fatai Adekunle
http://www.linkedin.com/e/hej71y-gpijbrp5
Congrats my friend,
I have no word to explain how much you deserve it.
Way to go.
-Pablo Meneses.
On Wed, Jun 29, 2011 at 7:44 AM, George Goglidze wrote:
> Hi all,
>
> As the subject suggests, it's official, I'm dual CCIE #19926 R&S and Voice
> starting yesterday.
>
> Finally, it's a relief,
Dear voice Users,
I have created a group on Skype where we can communicate online with each
other to discuss our matters on urgent basis, you guys can add (
ccie.voice.group ) where you can be added to the group. Just copy paste this
request while adding "ccie.voice.group" ( I am a Cisco Voice Use
Hi George,
Big congratulation to you and you deserve it!
We appreciate your contribution to the list and hope to see you again.
Now go and get back your social life : )
Cheers,
Alex
On Wed, Jun 29, 2011 at 9:44 PM, George Goglidze wrote:
> Hi all,
>
> As the subject suggests, it's official,
Congratulation George you deserve it!
Sent from my iPhone
On Jun 29, 2011, at 9:44 AM, George Goglidze wrote:
> Hi all,
>
> As the subject suggests, it's official, I'm dual CCIE #19926 R&S and Voice
> starting yesterday.
>
> Finally, it's a relief, no more studying late, spending weekends o
Congratulations and enjoy being back in the land of the living :)
Earl Hough
CCIE #16508 (R&S/Security/Voice)
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of George Goglidze
Sent: Wednesday, June 29, 2011 9:44 AM
To: CCIE Voice online gro
Congrats, Where did you go in your 3 attempts? I wanna go there too :) LOL
Regards,
Mohamed Gazzaz
From: gogli...@gmail.com
Date: Wed, 29 Jun 2011 14:44:21 +0100
To: ccie_voice@onlinestudylist.com
Subject: [OSL | CCIE_Voice] Passed
Hi all,
As the subject suggests, it's official, I'm dual CC
congratulatins
and thank you for the posts and explanations that you gave to the voice
community
2011/6/29 George Goglidze
> Hi all,
>
> As the subject suggests, it's official, I'm dual CCIE #19926 R&S and Voice
> starting yesterday.
>
> Finally, it's a relief, no more studying late, spending we
Hi all,
As the subject suggests, it's official, I'm dual CCIE #19926 R&S and Voice
starting yesterday.
Finally, it's a relief, no more studying late, spending weekends on a
computer, making calls, my neighbours think I escaped a psychiatric, after
hearing voices at night "TEST VOICEMAIL FOR HQ PH
This is a 3560 running the newest code and its odd that it's not creating a
trunk. I'll try a 3750 see if it's different.
-Original Message-
From: Bill Lake [mailto:whl...@gmail.com]
Sent: Tuesday, June 28, 2011 9:08 PM
To: Mike
Cc: Jason Langenfeld; ccie_voice@onlinestudylist.com
Subject
The best way is to test on your rack to see what happens without and then
with those commands during srst and in normal operation having enabled your
voice and voip dialpeer debugs. Just my two cents towards being an expert.
Rogers
CCIE #28970 (Voice)
On 29 June 2011 09:01, donny f wrote:
> h
hi all,
In stst mode "none", do we still need this command ?
1) dial-peer hunt 2
2) add-preference 9 in the ephone-dns
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and loo
35 matches
Mail list logo