Hi Guys
I've got 2 dual ethernet Cisco 1605 routers connected to each other via 2
cascaded hubs.Both sets of interfaces are set up for HSRP.(eth0 of both routers
are in one HSRP group & eth1 are in another HSRP group). Both routers have
also been set up to staically NAT a device(which will be
ch ?
Any thoughts will be appreciated.
Thanks
Simon Watson CCNP.Get Your Private, Free E-mail from MSN
Hotmail at http://www.hotmail.com">http://www.hotmail.com.
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Rep
Hi Guys can you help me
I've set up a static NAT entry on a remote dual ethernet router(name of router is
remote1), the global address that the local device will translate to is 10.10.10.100
this Global address is not in the subnet of the IP address on either interface, so I
have set up a lo
Hi Guys
I've got a customer who has a VSAT WAN network consisting of Cisco routers,
who has for a point to point connection between 2 routers used different
subnet masks i.e on the interface of one router the IP address is 172.16.8.1
Mask 255.255.240.0, on the interface of the router at the o
Hi Guys
Can someone tell me what are the minimum system spec(hardware & software) I need to install Ciscoworks 2000 for NT on a System.
Many Thanks
Simon WatsonGet more from the Web. FREE MSN Explorer download : http://explorer.msn.com
_
FAQ, list arch
Hi Guys I'm looking to take the CCDA & CID exams in the next six weeks to
become a CCDP.What are the best books to get to help me pass both exams,
I've got Pricilla's Top-Down Network Design and a CD-ROM of Designing
Cisco Networks (Version 2/1998). will these suffice. Than
I would say a,& d (assuming you meant to put "d" instead of the second
"c") As Store & forward stores the whole frame before forwarding it for
error checking .The last question is a trick as cut-through does not
forward on the layer 3 dest address but the layer 2.
Rgrds
Simon
>From: "Ar
Hi Guys I have just installed a 3660 and 7 2600's (the 2600's connected
to the 3660with 256k WAN links via 2 quad serial cards on 3660). ospf
configured(all routers on area 0), I have just changed the compression
from software to hardware to ultilize the AIM modules installed in both
the 3660 & 26
> > multicast (got to
> > know TAC people all across the world).. I'll try to dig up
> > the bug ID.
> >
> > What image are you using?
> >
> > Bob
> >
> >
> > > -Original Message-
> > > From: Simon Watson [mail
Hi Guys
I'm looking over a WAN network comprising of 7 2600's connected to a 3660
over 256k kilostream links.Software compression is set on all the WAN
links.I need to upgrade the IOS on all the routers from 12.0(7) to
12.2(x).My plan was to upgrade the remote routers first one by one, and th
Hi Guys
Talking about Cat 4006 & L3 Blades.
I've got 2 4006 with L3 blades, and I'm still trying to work out the
relationship between the Physical interfaces (gigabit interface 1 & 2), and
the logical interfaces (gigabit interface 3 & 4).
I know that the logical interfaces connects to the bac
Hi Guys I am setting up a Cisco 3660 with remote dialling access for ISDN
& PSTN users(30 Digital Modem Module & Pri Module installed), everything
seems ok, however when a ISDN User dials in to the 3660 after approx 160-
180 seconds the user gets kicked out of the 3660(The user is typing at
the ti
Dear Guys
Just Letting you know that I've just passed my CCNP.
The path I took was the FRS exam and then the CIT
got 900 out of 1000 on the FRS( 91% ACRC,91% CMTD,79% CLSC) & 778 out off
1000 for the CIT.
I found the CIT the hardest exam, make sure you know ISDN well as there was
a lot of IS
2.0 route.
Unfortunatley I can't help you much with recommeded reading, I had the
student course work for all the exams plus the cisco ACRC book from
ciscopress.
Rgrds
Simon
>From: "Phan H. Son" <[EMAIL PROTECTED]>
>To: "Simon Watson" <[EMAIL PROTECTED
Hi Guys
I have a catalyst 6509 with 2 * Gigabit ethernet ports on the supervisor
module(module1) & 3 further modules with 8 * Gigabit ethernet ports on each
module(modules 2,3 & 4).
I initially wanted to set up a Gigabit Etherchannel with one of the ports on
the supervisor module with one o
study for the 2.0 versions and take the v2.0 exams
Thanks in advance
Simon Watson CCNA
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com
___
UPDATED Posting Guide
study for the 2.0 versions and take the v2.0 exams
Thanks in advance
Simon Watson CCNA
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com
___
UPDATED Posting Guide
Hi Guys I'm going to install a secondary router on a Token-Ring Source
Route Bridge Network, and use HSRP between the two routers for
redundancy. On the current router the SRB config on the Token Ring
Interface is: "source-bridge 101 2 300". On the secondary router's
Token-Ring interface is it ok t
Hi Madman
Are you recommending me to configure both Token-Ring HSRP interfaces with
the same SRB statement ? i.e "source-bridge 101 2 300".
Thanks
Simon.
>From: MADMAN >Reply-To: [EMAIL PROTECTED] >To: Simon Watson >CC:
[EMAIL PROTECTED] >Subject
Thanks Dave
>From: MADMAN >Reply-To: [EMAIL PROTECTED] >To: Simon Watson >CC:
[EMAIL PROTECTED], [EMAIL PROTECTED] >Subject: Re: SRB & HSRP
[7:62660] >Date: Fri, 07 Feb 2003 15:34:50 -0600 > > > Hi, > > I would
have to look at the DLSW redundancy configs
Hi Guys I am based in the UK and have aquired some 2501 DC routers,
I want to use the routers to set up a home lab but I only have AC power
supply is there some form of AC/DC adaptor I can buy to plug my AC supply
in and be converted to DC for the routers ??? Thanks Simon
Hi Guys I am based in the UK and have aquired some 2501 DC routers,
I want to use the routers to set up a home lab but I only have AC power
supply is there some form of AC/DC adaptor I can buy to plug my AC supply
in and be converted to DC for the routers ??? Thanks Simon
Hi Guys
I'm being offered 16MB DRAM Simms that were once in a Cat RSM module.
Can I install these into a 2500 Router ??
Thanks
Simon
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=64719&t=64719
--
FAQ, list archives, and sub
Hi All
I will soon get a 16MB DRAM that was in a Cisco 3600, can I install it in a
Cisco 1603.
Thanks
Simon
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=65323&t=65323
--
FAQ, list archives, and subscription info: http://www.
Hi Guys I hope you can help me. A client has a AS5300 with old Modem
cards in it, who are going to upgrade to the new CC2 Modem module.To
upgrade to the new module the Boot Rom, System Flash,DRAM SIMMS,IOS &
Modem Software will need to be upgraded. The client is asking me "in what
order shall I st
Hi Guys
As the above heading says I'm going to install a Cisco (formerly Arrowpoint)
CSS switch and I just wanted to know how to configure URL load balancing on
it as this is what the customer is requesting.
Many Thanks in advance
Simon W
Hi Guys
I've installed Ciscoworks 2000, at a clients site with 2 Cat 6509's & 12 Cat
3548's. In resource Manager I'm setting up syslog to report messages from
the switches to CW2000, when I check the syslog reports on where I should
expect to see the IP address of the switch that sent the mess
Hi All Long time no speak hope everyone is having a blessed Christmas I've
a Client who has a WAN network comprising of a Cisco 3660(centre) &
several 2600's (currently each WAN link is a 256k lease line, each line
will soon be upgraded to LES10 Circuits). The client has ISDN backup on
all their
Hi Guys I'm going to a client's site that has a 2513 router with
11.3(11a) IOS (image is c2500-ds-l_113-11a.bin). 2 things: I'm looking
to set up HSRP on the router, should I have any issues with that level of
software ?Also is there an issues I should be aware of when configuring
HSRP on token ri
Hi Guys I'm going to a client's site that has a 2513 router with
11.3(11a) IOS (image is c2500-ds-l_113-11a.bin). 2 things: I'm looking
to set up HSRP on the router, should I have any issues with that level of
software ?Also are there an issues I should be aware of when configuring
HSRP on token r
* Hi
I'm going to be installing PA-E3 modules in 7200 routers at 2 sites,
I
haven't got all the details from the client,all I know is that they
intend
to use the full 34Mbps between the 2 sites(most likely hdlc).
Is there any questions I should be asking the Circuit Provid
Hi Guys
A client wants a Cat 3550 configured for VLAN tagging, I have not done
one
of these before so how do I configure the switch, also there is a Cisco
2600
router also connected to the switch.Do I need to configure the router to
accomodate VLAN tagging (and any router that packets of the VLAN
Hi Guys
A client wants a Cat 3550 configured for VLAN tagging, I have not done one
of these before so how do I configure the switch, also there is a Cisco 2600
router also connected to the switch.Do I need to configure the router to
accomodate VLAN tagging (and any router that packets of the VLAN
n occur.Also would it be best to enable the layer 3 capabilities of
the switches, or to let the routers do the work.
I'm looking forward to your answers
Thanks in advance
Simon.
----- Original Message -
From: "Henrique Issamu Terada"
To: "simon watson"
- Original Message -
From: "simon watson"
To: ; "Henrique Issamu Terada"
Sent: Wednesday, July 02, 2003 11:08 PM
Subject: VLAN Tagging on Cat 3550 Another question [7:71703]
> Hi
>
> Some how I was thinking VLAN tagging was something more than just
"Tr
- Original Message -
From: "simon watson"
To: ; "Henrique Issamu Terada"
Sent: Wednesday, July 02, 2003 11:08 PM
Subject: VLAN Tagging on Cat 3550 Another question [7:71703]
> Hi
>
> Some how I was thinking VLAN tagging was something more than just
"Tr
n occur.Also would it be best to enable the layer 3 capabilities of
the switches, or to let the routers do the work.
I'm looking forward to your answers
Thanks in advance
Simon.
----- Original Message -
From: "Henrique Issamu Terada"
To: "simon watson"
Hi All
My CCNP expires on the 20th July.Are there deadlines set to re-certify in a
certain time frame that if you do not you have to take the whole 4 exams
again.
Also are there any good books to brush up on things that were not in the CCNP
three years ago ??
Thanks
Simon.
Message Posted a
Hi PriscillaI'm in the same position as John (Cert expires on the 21st).
But I'm going to give the re-cert a go I've printed out the the MPLS
supplement you suggested to look on, will this be sufficent for the MPLS
portion of the test.Also the Catalyst 5K was the principle switch in the
switching p
Sorry
I meant MLS.
Thanks Karen.
- Original Message -
From: "Karen E Young"
To: "Simon Watson"
Cc:
Sent: Monday, July 14, 2003 4:45 PM
Subject: Re[2]: CCNP ReCert Questions [7:72071]
Simon,
Careful there! Don't mistake MLS for MPLS. Two different anima
Hi Guys
Just a quick question on the Cisco Certification Challenge questions found on
downloaded from Cisco.com.Im taking my CCNP recert in a few days and just
wanted to know if these challenge questions on each CCNP segment is of a
comparable level as in the actual exam.
Thanks
Simon.
Messa
Hi John
At the moment I'm just going through my old ACRC,CLSC,CMTD & CIT stuff
coupled with "Doyles" Routing TCP/IP & Cisco's Network Design & Case Studies
for IS-IS & BGP, an MLS supplement Priscilla O recommended & I'm going to go
through test questions from CCxx Productions.
What about you Joh
Good Review
However one correction, you've mentioned that EIGRP is a link state routing
protocol, when it is a "hybrid" distance vector protocol.
Take Care
Simon.
- Original Message -
From: "Andy Barkl"
To:
Sent: Wednesday, August 13, 2003 2:18 AM
Subject: Cisco CCNA 640-801 exam revie
43 matches
Mail list logo
