Re: Stus-List Fw: HELP aluminum bolt

2013-07-26 Thread Don Wagner
My pedestal bolts are SS without a problem. Aluminum bolts are easily corroded in the salt environment, and are as strong as SS. Use SS, but be sure to properly isolate it with Tef-Gel, Silicone, or other SS/Al isolation materials. Don Wagner C&C 41 CB Der Baron Hull # 93---

Re: Stus-List Yanmar 3GMF Starting Problem

2013-09-20 Thread Don Wagner
I had a similar problem, but discovered the the battery (~ about 5 yrs old) was getting weak, and always started on the 2nd or 3rd try. How old is your starting battery? My mechanic suggested that this was typical of an aging battery. Don Wagner C&C 41 CB Der Baron - Original Mes

Re: Stus-List Annapolis Boat Show

2013-10-13 Thread Don Wagner
ep, since he seemed busy, and I wasn't prepared to wait. Maybe next year they'll have better representation. Don Wagner C&C 41CB Der Baron - Original Message - From: Joel Aronson To: cnc-list@cnc-list.com Sent: Friday, October 11, 2013 2:38 PM Subject: Stus-List

Re: Stus-List Installing shaft zincs

2013-11-28 Thread Don Wagner
water pump grease, but he said most any grease would do. This all sounded like hokum to me, but considering the source, I tried it. He also tought me some thing about protecting my centerboard cable, and other parts of the CB system. Don Wagner C&C 41 CB Der Baron On Nov 27, 2013, at

Re: Stus-List Installing shaft zincs

2013-11-28 Thread Don Wagner
find this helpful. Don Wagner C&C 41 CB Der Baron On Nov 28, 2013, at 12:27 PM, "dwight" wrote: > Richard > > I would guess that a liberal application of waterproof grease and fitting > small sacrificial zinc anode(s) to the cable would help a lot > > From:

Re: Stus-List 30 MKI weather helm

2013-12-04 Thread Don Wagner
the center of effort forward. Typically the helm was well balanced over a wide range of wind speeds. Just some thoughts from and old 30 MK 1 owner. Don Wagner Red Baron C&C 30 MK1 1973 hull # 100 Now owner of: Der Baron C&C 41 CB 1986 hull # 93 From: Ronald B. Frerker Sen

Re: Stus-List Engine compartment ventilation

2012-09-28 Thread Don Wagner
nt. A 12 volt blower, switch activated, is installed in the exhaust vent line. I hope this helps you Don Wagner C&C 41 CB 1986, Hull # 93 Der Baron - Original Message - From: Pierre Tremblay To: C&C Mailing List Sent: Friday, September 28, 2012 9:22 AM Subject:

Re: Stus-List Main Masthead sheave

2012-09-29 Thread Don Wagner
to do with the mast unstepped, but I have done it from a bosuns chair. Be careful not to drop anything, down the mast or on the deck. I've not had any further problems, since I replaced the wire halyards and the Aluminum sheaves. I was unable to find stock direct replacement sheaves. Hope this

Re: Stus-List Outhaul

2012-12-30 Thread Don Wagner
, a clean boom will only give them a knot/ headache/ etc. A boom with cheek blocks, etc will probably draw lots of blood and more. Keep the boom clean, if you can Don Wagner C&C 41CB Der Baron West River MD - Original Message - From: Jake Brodersen To: cnc-list@cnc-list

Re: Stus-List Spinlock Clutches

2013-04-24 Thread Don Wagner
I would suspect the cams. You can easily inspect them for wear. I've had to replace the cams several times. When you buy the cam, the spring is included since it's part of the assembly. You might also inspect the bottom plate, but it seems to wear less, and it not as critical. Don

Re: Stus-List third battery

2013-04-27 Thread Don Wagner
t to prevent any metal objects from shorting to the terminals, but this cover is by no means gas tight. Never had a problem. Just my .02 $ Don Wagner C&C 41 CB Der Baron Hull # 93 1986 - Original Message - From: Richard H. Bernstein To: cnc-list@cnc-list.com Sent: Saturda

Re: Stus-List C&C30 MK1 Steamer light?

2013-05-09 Thread Don Wagner
hull # 100, "Red Baron" Bought her new in Nov 1972. Sold her in 1986 When I bought my present C&C 41 CB, Der Baron. Don Wagner - Original Message - From: "Curtis" To: Sent: Thursday, May 09, 2013 3:09 PM Subject: Stus-List C&C30 MK1 Steamer light? Where mi

Re: Stus-List Starting a Universal

2013-05-16 Thread Don Wagner
depressed as suggested by the manual, but should not have it depressed when starting. The reason given was that the extra stress on the red hot glow plug during start up will reduce the lifetime of the glow plug. Does anyone have any experience with that?? Don Wagner C&C 41 CB Yanmar 3HM35F-

Re: Stus-List Centerboard issue

2013-05-20 Thread Don Wagner
any other details, I'd be interested . Please let me know if/when you learn any further details. Don Wagner - Original Message - From: Tony Wroblewski To: cnc-list@cnc-list.com Sent: Monday, May 20, 2013 8:34 PM Subject: Stus-List Centerboard issue Does anyone on the

Re: Stus-List Stopping a diesel

2013-05-24 Thread Don Wagner
the engine if the engine room is flooded with Halon or other similar HFCs. The fire will be extinguished (no oxygen) but a diesel will run with the Halon environment West Marine sells devices for this purpose--- see page 187 of their 2013 catalog. Don Wagner Der Baron C&C 4

Re: Stus-List Winches Needed

2013-06-11 Thread Don Wagner
On my Barient winches, the part that holds the pawls in place is made of bronze. When it failed, I found a welder to build up the material, and a machine shop that did some machining to finish it. Total cost < $50 It's been more than 15 years ago, and it's just fine. Don Wagner

Re: Stus-List Open House--Now boat names

2014-03-05 Thread Don Wagner
In Annapolis, a Wylie 30, owned by 2 Doctors, a psychiatrist and a proctologist was named “Heads and Tails” From: Rick Brass Sent: Wednesday, March 05, 2014 5:23 PM To: cnc-list@cnc-list.com Subject: Re: Stus-List Open House A local racer used to have a boat named after his wife. After the div

Re: Stus-List C&C 30 mk1 rudder design

2014-06-11 Thread Don Wagner via CnC-List
From: Della Barba, Joe via CnC-List Sent: Wednesday, June 11, 2014 3:10 PM To: cnc-list@cnc-list.com Subject: Re: Stus-List C&C 30 mk1 rudder design My boat is a big version of the old C&C 30. I have noticed no issues in reverse with my rudder. I rarely use my tiller, so I can’t really tell y

Re: Stus-List C&C 30 mk1 rudder design

2014-06-11 Thread Don Wagner via CnC-List
oat for racing or cruising with 4 – 5 crew. Don Wagner C&C 41 CB Der Baron From: Della Barba, Joe via CnC-List Sent: Wednesday, June 11, 2014 3:10 PM To: cnc-list@cnc-list.com Subject: Re: Stus-List C&C 30 mk1 rudder design My boat is a big version of the old C&C 30. I have noticed

Re: Stus-List binnacle light

2014-07-12 Thread Don Wagner via CnC-List
d. Good luck Don Wagner C&C 41 CB Der Baron West River , MD From: Joel Aronson via CnC-List Sent: Saturday, July 12, 2014 12:01 PM To: cnc-list@cnc-list.com Subject: Stus-List binnacle light There is no power to my binnacle light. I've tried every breaker and switch. No luck. I can

Re: Stus-List Alternator for Yanmar 3GM30

2014-08-14 Thread Don Wagner via CnC-List
Joel You might want to talk to “Mamock’s . They are on Legion Ave in Annapolis. I’ve used them several times and found them easy to work with. Don Wagner’' C&C 41 CB Der Baron From: Joel Aronson via CnC-List Sent: Thursday, August 14, 2014 9:49 AM To: cnc-list@cnc-list.com Subject:

Re: Stus-List Replacement fuel sender for Landfall 38

2014-09-15 Thread Don Wagner via CnC-List
ably rectangular, if you know the depth, and Moeller has a depth unit to match. As I recall, the screw holes for the Moeller also matched the pattern for the old model. Don Wagner C&C 41 CB Der Baron From: Della Barba, Joe via CnC-List Sent: Monday, September 15, 2014 11:27 AM To: cnc-

Re: Stus-List Need help identifying a book

2015-01-25 Thread Don Wagner via CnC-List
/ Oxford Race. It was titled “Regatta” Muskrat was the funniest sailing book I’ve ever read. Hope you find it. Don Wagner C&C 41 CB Der Baron Shady Side MD From: Gary Nylander via CnC-List Sent: Sunday, January 25, 2015 3:10 PM To: Rick Brass ; cnc-list@cnc-list.com Subject: Re: Stus-List Need

Re: Stus-List C & C 35 Mk III CB Keel Bolts

2015-07-30 Thread Don Wagner via CnC-List
er have seen Aluminum anything used in the bolts on a C&C. Don Wagner Der Baron C&C 41 CB From: Jake Brodersen via CnC-List Sent: Thursday, July 30, 2015 8:57 PM To: cnc-list@cnc-list.com Cc: Jake Brodersen Subject: Re: Stus-List C & C 35 Mk III CB Keel Bolts Paul, I agree with you

Re: Stus-List Howling rigging

2015-08-01 Thread Don Wagner via CnC-List
phenomena with some pix. You might also search “ von Karmann vortex street” I’ve experienced it in my rigging, and occasionally from my centerboard at certain wind speeds or boat speeds Don Wagner C&C 41 CB Der Baron From: Joel Aronson via CnC-List Sent: Saturday, August 01, 2015 2:39 AM To:

Re: Stus-List Howling rigging

2015-08-02 Thread Don Wagner via CnC-List
Oops! Thanks for the correction Leslie. Being an EE, not a ME or fluids guy I should be more careful. I worked at APL and our auditorium is named after a not so famous scientist. Don Wagner C&C 41 CB Der Baron -Original Message- From: Leslie Paal via CnC-List Sent: Sunday, Augus

Re: Stus-List new topic mast height C&C 30 MKI

2015-08-10 Thread Don Wagner via CnC-List
that boat was a Hinkley Souwester 50?? Don Wagner C&C 41 CB Der Baron From: Rick Brass via CnC-List Sent: Monday, August 10, 2015 8:51 PM To: cnc-list@cnc-list.com Cc: Rick Brass Subject: Re: Stus-List new topic mast height C&C 30 MKI Three basic questions: Reducing 85 feet of air

Re: Stus-List 37+ Navteq hydraulic backstay hoses

2015-08-24 Thread Don Wagner via CnC-List
I’ve found that many Truck Repair centers have the capability to repair hydraulic lines and hydraulic cylinders. I believe I once used a place in Waldorf MD to do some work for me. It’s close to Solomon’s Island MD. You might check it out ! Don Wagner C&C 41 CB Der Baron From: Alan Bergen

Re: Stus-List 2015 Northeast @ Cedar Island

2015-09-04 Thread Don Wagner via CnC-List
Got itDon & Jean Wagner From: David via CnC-List Sent: Thursday, September 03, 2015 1:36 PM To: CNC CNC Cc: David Subject: Re: Stus-List 2015 Northeast @ Cedar Island Rob, Hey...I gets my pharms via mail. Smart fella eh? Corsair draft at 8' would eliminate most of those offerings. I

Re: Stus-List Boom Mainsheet Connections

2015-09-27 Thread Don Wagner via CnC-List
I found that the Harken Catalog contains lots of suggestions on how to rig your boat. They have a lot of mainsheet ideas, traveller configurations, spinnaker ideas, etc. Have you checked out their catalog? Or call their tech guys. They have been a big help to me!! Just my $ .02. Don Wagner

Re: Stus-List Winterizing -- Raw Water Intake

2015-09-28 Thread Don Wagner via CnC-List
the Spring. Winterizing the water tanks is another story. Don Wagner C&C 41 CB Der Baron West River MD I From: David Knecht via CnC-List Sent: Monday, September 28, 2015 1:56 PM To: CnC CnC discussion list Cc: David Knecht Subject: Re: Stus-List Winterizing -- Raw Water Intake My solution is si

Re: Stus-List Winterizing -- Raw Water Intake

2015-09-28 Thread Don Wagner via CnC-List
system, changing filters, changing oil, removing mast head instruments, cleaning out bilges, removing floor boards, etc. so I usually have someone (maybe 2 crew) available to assist. I would definitely not do most of this winterizing by my self any way. Don Wagner Der Baron C&C 41 West R

Re: Stus-List Galvanic isolator - Good idea?

2015-10-28 Thread Don Wagner via CnC-List
this yourself, unless you can design the proper size diodes and capacitors and heat sink the box Just my$.02 Don Wagner C&C 41 CB Der Baron From: Josh Muckley via CnC-List Sent: Wednesday, October 28, 2015 12:48 PM To: C&C List Cc: Josh Muckley Subject: Re: Stus-List Galvanic iso

Re: Stus-List 33ii mainsail reefing

2015-11-29 Thread Don Wagner via CnC-List
ooted main. I not, have your sailmaker sew a slot in the foot to accommodate the bowline. Works great for me. Don Wagner C&C 41CB Der Baron West River MD -Original Message- From: Dave via CnC-List Sent: Sunday, November 29, 2015 7:58 PM To: cnc-list@cnc-list.com Cc: Dave Subject:

Re: Stus-List Engine Room Original Paint (Damian Greene)

2016-01-11 Thread Don Wagner via CnC-List
C&C would have used lead based paint. If not gel coat, maybe it could be epoxy. I do know that it sure doesn’t seem to be a latex, or oil based lead paint. Intellux sells a gray or white Bilge coat that is epoxy or polyester based I believe. Just my .02 $ Don Wagner Der Baron C&C

Re: Stus-List DC distribution panels

2016-01-24 Thread Don Wagner via CnC-List
When I needed a panel for my C&C 41 I went to a local sign maker. They matched the material and engraved the lettering I needed. They were familiar with making that style panel, and had a CNC machine that did it all. I don’t recall the cost but it didn’t seem to be excessive. Don Wagner

Re: Stus-List Nav Station Panel and Volt Meter Recommendations

2016-02-15 Thread Don Wagner via CnC-List
ving machine and did a great professional job. Don Wagner C&C 41 CB Der Baron From: Dennis C. via CnC-List Sent: Monday, February 15, 2016 2:03 PM To: CnClist Cc: Dennis C. Subject: Re: Stus-List Nav Station Panel and Volt Meter Recommendations http://www.ebay.com/itm/Blue-Sea-Systems-8051

Re: Stus-List Stern Ladder Hull Guard-Feet

2018-07-16 Thread Don Wagner via CnC-List
trick. Don Wagner Der Baron C&C 41 CB -Original Message- From: Danny Haughey via CnC-List Sent: Monday, July 16, 2018 8:51 AM To: cnc-list@cnc-list.com Cc: Danny Haughey Subject: Stus-List Stern Ladder Hull Guard-Feet Hello again, are there any clever ways to protect the transom

Re: Stus-List mystery item

2018-08-01 Thread Don Wagner via CnC-List
1 hull # 100 “Red Baron” from 1973 through 1985 and raced and cruised her a lot on the Chesapeake Bay. In 1986 I replaced her with a C&C 41 CB hull #93, “Der Baron”, and raced and cruised her a lot on the Bay too. By 2016 following some serious surgery. I gave up racing and but still do some

Re: Stus-List Mast Rake for C&C 41

2018-08-04 Thread Don Wagner via CnC-List
pre-bend. We did it in 1986,some I'm not sure what else we may have done. Since then, we mostly use the hydraulic backstay , the baby stay, or the runners to adjust the mast bend and the sail shape. Don Wagner C&C 41 CB Der Baron -Original Message- From: Matthew L. Wolford

Re: Stus-List Cutlass bearing

2018-09-24 Thread Don Wagner via CnC-List
ring. Don Wagner C&C 41 CB Der Baron___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray

Re: Stus-List C&C ownership

2018-09-28 Thread Don Wagner via CnC-List
en wonderful family boats and I’ve never regretted our choice. Don Wagner C&C 41 CB Der Baron hull # 93 Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https

Re: Stus-List [EXTERNAL] Re: Annapolis-Mid Atlantic Rendezvous Next Year

2018-11-01 Thread Don Wagner via CnC-List
I’ll second St Michaels. It has better accommodations for tourists, more shops, more restaurants, the best museum, a nice hotel, better choice of marinas, etc Don Wagner Der Baron C&C 41CB From: Della Barba, Joe via CnC-List Sent: Thursday, November 01, 2018 2:51 PM To: cnc-list@cnc-list

Re: Stus-List Winch grease

2018-11-04 Thread Don Wagner via CnC-List
I also prefer a teflon or silicone based grease. I avoid lithium based grease since they seem to dry out and get hard after a while. Don Wagner Der Baron C&C 41 CB From: Chris Graham via CnC-List Sent: Sunday, November 04, 2018 8:49 AM To: cnc-list@cnc-list.com Cc: Chris Graham Subject

Re: Stus-List Mooring Rights -- Any "Sea Lawyers" on the List?

2017-11-10 Thread Don Wagner via CnC-List
buoy, I suppose. Don Wagner C&C 41 CB Der Baron From: Jack Brennan via CnC-List Sent: Friday, November 10, 2017 9:35 AM To: cnc-list@cnc-list.com Cc: Jack Brennan Subject: Re: Stus-List Mooring Rights -- Any "Sea Lawyers" on the List? Sounds like an abandoned vessel to me. I

Re: Stus-List 2018 Mid-Atlantic C&C Rendezvous UPDATE Oct 26, 27, 28

2018-02-21 Thread Don Wagner via CnC-List
aval Academy events The Pirates Cove Inn and restaurant and marina in Galesville also has a few motel room the also are on the West River, where you could also berth your boat Just a thought if you’d rather not stay in Annapolis Don Wagner C&C 41 CB Der Baron West River, MD From: Joel Aro

Re: Stus-List Who made our masts?

2018-03-08 Thread Don Wagner via CnC-List
s at the time, but Jim? still had parts in a garage My steering, system, wheel, etc was produced by Edson I think Rob McLaughlin of South Shore facilitated part of my purchase. Don Wagner C&C 41 CB Der Baron From: Matthew L. Wolford via CnC-List Sent: Thursday, March 08, 2018 2:07 PM To:

Re: Stus-List How many shaft zincs?

2018-04-27 Thread Don Wagner via CnC-List
rked for me, and you might want to investigate. Don Wagner previously C&C 30 owner, now, C&C 41CB DerBaron West River MD From: kelly petew via CnC-List Sent: Friday, April 27, 2018 6:00 PM To: cnc-list Cc: kelly petew Subject: Stus-List How many shaft zincs? I have always installed t

Re: Stus-List Mast boot

2016-05-05 Thread Don Wagner via CnC-List
hite vinyl. They also make those piling caps that you see at many marinas Check them out ssicustomplastics.com/products/piling-caps Don Wagner C&C 41 CB Der Baron i From: Jean-Francois J Rivard via CnC-List Sent: Thursday, May 05, 2016 10:39 AM To: cnc-list@cnc-list.com

Re: Stus-List Singing Rigging

2016-07-25 Thread Don Wagner via CnC-List
s of their wings. I believe this reduces energy loss, reduces the vibration, and improves their fuel mileage. Don Wagner C&C 41 CB Der Baron West River MD -Original Message- From: Christian Tirtirau via CnC-List Sent: Monday, July 25, 2016 11:04 AM To: cnc-list@cnc-list.co

Stus-List PVC Insert for Cinkel Mast or Boom

2016-07-26 Thread Don Wagner via CnC-List
sail. Don Wagner C&C 41 CB Der Baron West River MD ___ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated!

Re: Stus-List Keel bolt weeping

2016-09-19 Thread Don Wagner via CnC-List
em was a manufacturing problem with C&C. Maybe yours is a simple thing like that Don Wagner C&C 41 CB Der Baron West River MD From: Barbara L. Hickson via CnC-List Sent: Monday, September 19, 2016 12:48 PM To: C&C List Cc: Barbara L. Hickson Subject: Stus-List Keel bolt weeping Hi L

Re: Stus-List Main sheet chafes

2016-10-08 Thread Don Wagner via CnC-List
! Don Wagner C&C 41CB Der Baron West River MD From: Joel Aronson via CnC-List Sent: Saturday, October 08, 2016 10:26 AM To: cnc-list@cnc-list.com Cc: Joel Aronson Subject: Re: Stus-List Main sheet chafes Brian, How old and large is that line? Is it too big for the sheave? If it is origina