Hm..
My K3S set to 100W says it is putting out 80W on 6M.
An external power meter also reads ~80W.
I did a gain calibration and there was no change.
But, now you got me thinking.
My 50-Ohm load is +30 years old and I doubt is rated for 50MHz.
___
73,
Jim - N4ST
-Original
Did you check the specs? I don’t think it is supposed to put out full 110
Watts on 10 or 6 meters.
Sent from my iPhone
...nr4c. bill
> On Jul 10, 2018, at 8:03 PM, Gary Smith wrote:
>
> What is the expected output on 6 meters?
>
> The K3 shows 110W
> The P3 watt meter says 73.1W
> The LP-
Have you run a Transmitter Gain Calibration from the K3 Utility
Application? If you do, be sure to use a good dummy load connected
direct to the radio with a known good short coax jumper.
The fact you have 3 different power indicating devices which all
indicate different power values, I'd say
Thanks Fred,
Guess I have some issues with my K3s then.
I think it's past warranty at this point.
I'll break out the K3 and try to get it
working in place of the K3s, send the K3s
back for repair and figure how to get WSJT
going with the K3 while 6 is still open.
73,
Gary
KA1J
> My K3S sho
Skip,
If you need additional trials for tuning with the KAT2, set the ATU menu
to ALT.
73,
Don W3FPR
On 7/10/2018 9:53 PM, Fred Jensen wrote:
Does the K2 ATU maybe find a better match if you to TUNE again quickly,
or is the first match the bestest it can do?
__
Does the K2 ATU maybe find a better match if you to TUNE again quickly,
or is the first match the bestest it can do?
73,
Fred ["Skip"] K6DGW
Sparks NV DM09dn
Washoe County
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman
Hey Dave, thanks for the reply. I’m using the mic that came with the radio.
It does have the buttons.
Another thing that is happening is that the frequency is jumping sometimes
by 1 kHz, I thought I was bumping the dial but that’s not the case, I was
watching the screen and the frequency jumped a
What is the expected output on 6 meters?
The K3 shows 110W
The P3 watt meter says 73.1W
The LP-100A says 60.1W
When I use the internal tuner it never
breaks into the higher power range, it
only outputs at 7 watts tops.
On all the lower bands it puts out 100
reliably.
Thanks & 73,
Gary
KA1J
Folks -lets end the breakers for KPA1500thread to relieve list overload for our
other readers.
Thread closed.
73,
Eric
Moderator from time to time..
elecraft.com
_..._
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/lis
i am only three days back catching up . this thread was closed.sri
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
Thi
Ok... I can’t stand it any longer.
The breaker you install has nothing whatsoever to do with the equipment your
going to use on that circuit. The breaker is chosen for the size of the wire
you run in the walls. PERIOD!!!
The amp is protected by the fuses in the amp! Not the circuit breaker.
but for 18$,,, including the suspension
it looks scool.
i bought a similiar if not identical... from banggood
it plugs right into the mic jack on the back of the k3 kx3 so
much for 'studio'
Me thinks it is for computer video gamers and bloggers.
and it works just li
The cable is indeed not cat-5, but rather 8 individual wires that carry power
and ground one way (to the box) and analog sensor signals back. The twist
action in CAT-5 does not help here at all.
The things to watch for are signal loss due to resistance (shouldn’t be too
bad, depending on the wir
Ladies and Gentlemen,
As a *Recovering Regulator* and a person who contacted my insurance
company when I was contemplating finishing my basement, let me share a
couple thoughts/experiences.
A couple of years ago I called my home owners insurance company, USAA, and
told the nice young lady who an
Thanks. First real info I've gotten. I said Cat5 because the documentation
mentions it and I believe it says you can use a standard Ethernet cable.
I haven't taken a close look at the coupler circuitry. If it's like most remote
couplers I've seen, a too-long cable can cause a drop in the DC volt
Code generally says 12 amps max on a 15 amp circuit.
On 7/10/2018 11:42 AM, Don Wilhelm wrote:
Think about what you normally plug into a 120 volt 15 amp receptacle -
does it always draw 15 amps? Certainly a hair dryer might, but your
cellphone charger does not.
___
You can get "null modems" that are just two back to back connectors.
Amazon, search on "null modem". They're small, cheap, and last a long
time. [:-)
73,
Fred ["Skip"] K6DGW
Sparks NV DM09dn
Washoe County
On 7/10/2018 11:32 AM, Don Wilhelm wrote:
Kent,
You should be able to plug the Palst
John,
Just because the Specification says 20 amps, that is the maximum current
draw for the amp - it does not say that the breaker must be 20 amps,
only that it must be 20 amps or higher.
A 30 amp breaker is fine if the wire is #10 or larger.
Think about what you normally plug into a 120 volt
Kent,
You should be able to plug the Palstar cable into the cable from the K3
RJ-45 to RS-232 dongle. A gender changer may be needed.
Worth a try anyway.
Or you could purchase a short RS-232 Crossover cable to replace the one
to the tuner.
73,
Don W3FPR
On 7/10/2018 12:10 PM, KENT TRIMBL
Are you using the Elecraft KX2 mic with the buttons? If not, try
disabling the buttons in the menu.
Otherwise, maybe a poor connection?
Hope that helps,
-- 73, Dave, N8SBE
Hey guys,
Anyone know why I keep seeing Ext. Mic Displayed on the screen of the
KX2
every once in a while when
Wayne,
You duplicated the line about the ATU:
ATU* matching range @ 100 W 10:1 (typ) 3:1 Allows monoband antennas to
be used on other bands
It's in the General and Transmitter sections.
Also, I would REALLY like to be able to plug a mouse into the P3, and
click my way around the SVGA screen
Per the manual 50% efficiency. So at 1500 watts output the. input would be abt
3Kw. A 20 amp ckt at 240 V would supply 4.8 Kw. Seems reasonable to have
adequate power for other equipment.
Bob, K4TAX
Sent from my iPhone
> On Jul 10, 2018, at 12:34 PM, "j...@kk9a.com" wrote:
>
> I based tha
Curt,
Elecraft is no longer able to procure the parts for the EC2 enclosure,
and it has been discontinued.
If you can find someone who previously added the KAT100 and KPA100 to an
EC2 enclosure, they might have the leftover front and rear and top
panels. You can supplement those parts with K2
Either plug the two cables together or with a “GenderChanger”.
Sent from my iPhone
...nr4c. bill
> On Jul 10, 2018, at 12:10 PM, KENT TRIMBLE wrote:
>
> The RS-232 thread comes coincidentally at a time when I have just experienced
> an RS-232 "gotcha."
>
> If you own a Palstar AT-AUTO you n
First thought is to download and read the assembly manual for the kit. I think
it’s a plug in device.
Sent from my iPhone
...nr4c. bill
> On Jul 10, 2018, at 11:57 AM, Scott Manthe wrote:
>
> Hi all-
>
> I picked up a used KX3 for a pretty good price. However, the VFO B encoder is
> defect
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: ht
I based that statement on the 20amp KPA1500 rating shown on page 28 of
their manual. Obviously this is incorrect or it is very inefficient, but
still a station can have multiple heavy duty rotators, computers, multiple
transceivers, etc.
http://www.elecraft.com/manual/E740301%20KPA1500%20Owners%20
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: ht
On 7/10/2018 9:13 AM, j...@kk9a.com wrote:
Yes you can run three conductor
Romex and have a 120v and 240v outlet but I do not see this as a good plan
as it could easily exceed 20 amps on one leg. Upgrading to higher amperage
circuit and you'll exceed the amperage rating for a standard 120v outlet
On 7/10/2018 7:10 AM, N2TK, Tony wrote:
> I did not in any way suggest using the ground wire for current. But
> many appliances such as the KPA1500, air compressors, water heater,
> etc. are 220VAC devices that only require 2 wires plus ground. If
> you look at the plugs on many of these type de
the standard cable is not Cat5, it's just a ribbon cable with RJ45's (I
think?) at each end.
Cat5 should work, though, and I'd be surprised if anything less than ~50ft+
would be an issue.
--
Jeff KC9WSJ
On Mon, 2018-07-09 at 23:51 -0400, Dick Green wrote:
> The W2 wattmeter comes with a 5-foot
Let's put this in monetary terms. 100 ft of 12/2 with ground is $56 at Home
Depot. 100 ft of 10/3 with ground is $138.
If you pay an electrician to do the work, the difference won't be 10% of
the bill.
If you do it yourself, following code and getting it signed off by an
electrician and inspected
For a few years my KX3 travels in a Pelican case that is about 9 x 6.5 x 4.
Aside from KX3, inside there is space for a log, 2 spools of wire, KX3
keyer, binding post, and 4S2P Li-Ion battery. The battery lasts a few 2 hr
outings.
Ignacy, NO9E
--
Sent from: http://elecraft.365791.n2.nabble.co
Don,
Yes, good point.
73,
Erik K7TV
-Original Message-
From: Don Wilhelm
Sent: Tuesday, July 10, 2018 8:56 AM
To: Erik Basilier ; Elecraft@mailman.qth.net
Subject: Re: [Elecraft] Breakers for KPA1500?
Erik,
One of the benefits of using a new and direct line to the breaker box to power
And to answer your question , yes the PAE-KX33 runs the KX3 at full power.
:)
On Tue, Jul 10, 2018 at 12:03 Walter Underwood
wrote:
> I expect he’s talking about the Powerwerx SS-30DV, which is resold by
> Elecraft.
>
> The smallest, lightest 22 A PS I know of is the Gamma Research HPS-1A. It
Neither Tony or I suggested making a 120v circuit from the two wire 240v
line using the ground as the neutral. Yes you can run three conductor
Romex and have a 120v and 240v outlet but I do not see this as a good plan
as it could easily exceed 20 amps on one leg. Upgrading to higher amperage
circu
The RS-232 thread comes coincidentally at a time when I have just
experienced an RS-232 "gotcha."
If you own a Palstar AT-AUTO you need to remember that the RS-232 cable
(null modem) originally supplied with the tuner is cross-wired (pin 2 to
pin 3, and pin 3 to pin 2). This is the correct wi
Good Morning All:
Does anyone know if the EC-2 project cabinet is still available? I see
info on it on the site but no info as to ordering one. Want to put a
Panadapter into one.
Thanks,
Curt
KU8L
__
Elecraft mailing list
Home: ht
I expect he’s talking about the Powerwerx SS-30DV, which is resold by Elecraft.
The smallest, lightest 22 A PS I know of is the Gamma Research HPS-1A. It
weighs 1.25 pounds and costs $130. It uses a super capacitor to provide 22 A
for transmit, then recharges it while you are listening.
http://
Hi all-
I picked up a used KX3 for a pretty good price. However, the VFO B
encoder is defective. It has lost the push-in switch functionality. So,
I need to replace it. If you've replaced one of the encoders, how harry
is the process? I built my KPA500 and am relatively competent with a
solde
Erik,
One of the benefits of using a new and direct line to the breaker box to
power both 240 and 120 in the shack is that the 120 volt (and the 240
volt) green wire ground is a straight run to the breaker box instead of
being run willy-nilly from receptacle to receptacle through the house.
T
If you're talking about an Astron SS30, that's a lot of beef to run a KX3.
Are you running the KXPA100 also? Do you want to house that in your case
as well?
I have my KX3, PX3 and a LiFePO4 battery (and mic/key/etc) in a Harbor
Freight case, the Apache 3800. The power supplies come along in a
It is abundantly clear that 3 conductors plus protective ground are needed
if there will be any load, on the same circuit, that requires 120V as
opposed to 240V only. I certainly agree 100%. It is also clear that the
person who installs 240V for the PA only could get away with one conductor
less. I
Howdy men
I’m thinking of getting a hard shell case to put my KX3 kit in. I want it to
hold not only the KX3 but one of the SS30 power supplies and accessories.
Anyone done this? Recommendations?
Ronnie W5SUM
__
Elecraft mailing list
Ho
Yes Tony,
I added that bit in case someone wanted to get 120 volts from the 2 wire
plus ground receptacle.
While it will work if you use the ground wire as the neutral conductor,
it is a severe violation of code to do so, and it is highly dangerous
from a safety standpoint.
The KPA1500 is a
Don,
I did not in any way suggest using the ground wire for current. But many
appliances such as the KPA1500, air compressors, water heater, etc. are 220VAC
devices that only require 2 wires plus ground. If you look at the plugs on
many of these type devices there are only three prongs - each
Tony,
While it is possible and safe to use only two wires plug safety ground
(Green Wire Ground) for a 240 volt receptacle or 240 volt only device
(in-home air conditioner, dryer, etc), it is quite unsafe to split off
for a 120 volt supply using one hot and ground - in that case (such as a
ra
I split off with a 120 volt duplex outlet from L1 and another from L2
and I have a 240 volt outlet for the amp. Thus both neutral and ground
are needed for the 120 volt duplex outlets. The configuration is very
adequate, legal, and safe for the entire station.
73
Bob, K4TAZ
On 7/10/2018 6
Hi,
yes guys, it is exactly that "LPF T/R Switch Rework" mod...
Official and approved document is: Elecraft modification manual for LPF T/R
Switch Rework Rev. E
The necessary parts are achievable at DigiKey, Mouser etc. (see my article
on blog)
The ordering number if you want to ask for the kit a
Get an inexpensive RS-232 breakout box. The LEDs and jumpers will help you
see what is happening on the data and control lines and enable you to
make/verify any cable you need. Compact gender changers address the
male/female connector issue as well as the 25 pin/9 pin conversion. I
still have a
In broadcasting - we learned very quickly interfacing equipment with RS232,
that if it worked once it would continue to work.
Back in the beginning of using RS232 interfaces (cira. 70s) one of our the
engineers made a box with input/output pigtails in both male and female with
a rotary switch
Perhaps he was speaking of the 12 meter lowpass filter mod.
Some earlier KPA500s had a problem on 12 meters. Elecraft came out with a
mod you could perform yourself or send the amp in and they would do it for
you for free except you had to pay the shipping.
You didn't have to send the whole amp bac
The nice thing about the PDF manual is you can have it on your phone or
tablet and it is always with you. Also you can search it.
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net
I concur, I used Romex which had 2 conductors plus a ground. Perhaps he
meant that the ground wire should be the same size as the two conductors
but I am not sure how much control you have over this using standard
cable. While adding this circuit I also ran a dedicated 120v outlet for
the radio and
Sorry I missed it, but what is this mod for? Is it Elecraft approved?
Thanks & 73 de W5SV - Dave
> On Jul 10, 2018, at 06:02, Petr, OK1RP/M0SIS wrote:
>
> Hi,
>
> upon some emails regarding this modification procedure steps I am sharing
> this note also over here on the reflector. (I am sorr
I do not understand the need for three wires plus ground. For a clothes dryer
outlet a neutral is required to get 110VAC from one of the phases to the
neutral. But for amps you only need both phases and a ground. The plugs are
three wire, not four.
73,
N2TK, Tony
-Original Message-
Fro
Hi,
upon some emails regarding this modification procedure steps I am sharing
this note also over here on the reflector. (I am sorry if its bothering for
someone...)
I am recommending after several mods done - when Q5 is removed > do not
install new BU931T back to its place for now. Go to another
Yep. When you're trying to get 50-60 dB down, EVERYTHING has to be done
very well. Several years ago, I was not achieving the harmonic
suppression I thought I should, so I bought a spool of BuryFlex (RG8
with a robust copper braid shield) and replaced every piece of coax
inside my shack. I did
58 matches
Mail list logo