For AM users, could we get the ability to invert the voice phase as a
feature of the K3? This would allow us to make sure that the audio phase
orientation is correct where the positive peaks are always greater than the
negative peaks. Even better, it would be cool if the rig could auto detect
an
Now that the K144XV is available and a lot of us are planning to use it to
drive microwave transverters, it would be really nice if there was some way to
easily adjust IF gain. I know there was a gain change after 3.97 so it appears
this is available in the firmware. Is there a way that along wi
Experience has shown me that I can more easily tune to a desired frequency
that is 'kHz.000' without the visual distraction of the 10Hz digit. Is it
possible to create a setting whereby the 10Hz digit can be shut off from
view as the 1Hz digit can be via the FINE button? E.g.. kHz.0 vs. kHz.00 o
Hi everyone,
As a recent purchaser of a factory built K3/100 with the lot (except for the
second receiver) I'd first of all like to thank the folk at Elecraft and in
particular Wayne and Eric for making this wonderful radio.
I have used it for a little bit on HF but it's mainly been on 6 & 2M her
If you happened to read W3IZ's review of the FTDX9000MP in the July QST you
will find an interesting comment on page 46. I don't know what it is but I
want it on my K3. Here's the quote:
"When activated, the contour acts like a super duper ninja CW filter that
makes the desired signal sound as if
The capability to operate CW while in the SSB mode is wonderful. However,
it does not work when in the Split mode. This would be a really valuable
feature when operating on 40M in the SSB DX contest (at least for me)
because I have to re-tune the antenna every few kilohertz. Is there another
way
Semon N7CW ; elecraft@mailman.qth.net
Sent: Saturday, 25 October, 2008 17:43
Subject: Re: [Elecraft] [K3] Feature Request
Hello All,
As a quick note, it would also be nice IF the frequency display would
display the TX freq, rather than the RX only.
73, Scott WA6LIE
K3 #1993
From: Bud Semon N7CW
Sent
The 'flashing TX' annunciator on the LCD (when TX is disabled) is not
catching enough for my aging eyes.
I'd like the red TX LED to also gate, at the same rate, when I attempt
to transmit with the TX disabled.
Seems minor, but, I wish I had a quarter for every time I cussed the
other guy out for
Hi folk,
i would like to have the key out connector switched during ³Tune². That
would be a
useful improvement for tuning linear amplifiers.
73 de Uli (DL4YCM), K3/10 #SN 2411
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a s
Arnie: I have to agree with you. In the "old" days we used to call
it "going Barefoot". Every AMP has a STBY switch. I just checked
ALS-600 and sure enough it HAS one. I'm not one to advocate making
something easy more complicated. From Wayne's tone about upcoming dual
receiver mo
Just preparing a station for the Centenary of Boy Scouts in a week or
two's time and remembered a real annoyance. The Kenwood HF rigs we use
(you don't think I'm gonna let the young 'uns play with my K2 do you!)
do not have any easy facility to allow both headphone and speaker
simultaneously. Abso
There will be great interest throughout the life of
the K3 product from users about which specific
features or fixes are on the "to be added list", the
relative priority, and when they might become
available. !!!
[Elecraft] K3 Feature Request
J. Edward (Ed) Muns w0yk at msn.com
Tue Ju
If you activate Noise Reduction (NR) on a mode (like CW), NR is on for
all modes on that band. Request NR to follow both mode and band. For
example, if you have NR selected for 40m CW, and change to LSB, NR is
OFF (unless previously activated for that mode).
Thanks,
- 73, John, N0TA
___
I use the internal K3 message memories when operating as DX in an ssb contest.
One of the biggest problem I face is the delay both in initiating the message
(from an external application) and the delay between the end of the message and
back in the receive mode. From experiments, both of these
Would it be possible to have an option that will either work the way it
does now, or will preserve the SPLIT setting if you make a quick QSY to
another band and then come back?
I'm officially on the "Didn't Get The 'UP' Memo" list as a result of a
quick check of 30 and return to 20. I did rea
Sticky Noise Blanker.through on/off cycle and band changes.
Dick - KA5KKT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
It would be wonderful if there were a CONFIG option to have CWT SPOT
zero beat using RIT instead of VFO A. This would be very useful
during contests when CQing.
73,
Hank, W6SX
Mammoth Lakes, California
Elevation 8083 feet in John Muir's Range of Light
_
Override / Bypass for RX and TX EQ. One button macro or similar.
73,
Dick - KA5KKT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft
10 Minute Timer - Sound, 'Beep, Beep, Beep.' Alternate, Flash or Dim
Display and/or Panel Lights. Reset Timer. Countdown on clock display.
73,
Dick - KA5KKT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elec
On 10/5/2010 5:11 PM, Tim Tucker wrote:
> incorrect phase orientation
The correct word to say what you mean is POLARITY, NOT PHASE. Phase is
a continuously valued function, and has the units of degrees. Polarity
is the word that describes whether the waveform is inverted or not.
Changing the
OK, thanks for the education. I'm not an RF engineer, but every product on
the market I've come across (doesn't mean much) and discussion I've read
(start with http://www.nu9n.com/am.html) calls what I'm talking about as
phase inversion. They could all be using the wrong term for all I know.
I c
On 10/5/2010 5:58 PM, Tim Tucker wrote:
> OK, thanks for the education. I'm not an RF engineer, but every product on
> the market I've come across (doesn't mean much) and discussion I've read
> (start withhttp://www.nu9n.com/am.html) calls what I'm talking about as
> phase inversion. They could
Or, he could scour E-Bay for a Kahn Symetra-Peak!
-lu-w4lt-
Message: 37
Date: Tue, 05 Oct 2010 17:39:37 -0700
From: Jim Brown
Subject: Re: [Elecraft] K3 Feature Request
To: elecraft@mailman.qth.net
Message-ID: <4cabc549.6000...@audiosystemsgroup.com>
Content-Type: text/plain; charset=ISO-
> Message: 37
> Date: Tue, 05 Oct 2010 17:39:37 -0700
> From: Jim Brown
> Subject: Re: [Elecraft] K3 Feature Request
> To: elecraft@mailman.qth.net
> Message-ID:<4cabc549.6000...@audiosystemsgroup.com>
> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
>
>
> >
> > -lu-w4lt-
> >
> > Message: 37
> > Date: Tue, 05 Oct 2010 17:39:37 -0700
> > From: Jim Brown
> > Subject: Re: [Elecraft] K3 Feature Request
> > To: elecraft@mailman.qth.net
> > Message-ID:<4cabc549.6000...@audiosystemsgroup.com>
> &
using electrets
on AM.
If a phase scrambler were part of the K3's DSP, any thought as to how much
DSP resource utilization is required?
Paul, W9AC.
- Original Message -
From: "Tim Tucker"
To:
Sent: Wednesday, October 06, 2010 12:34 AM
Subject: Re: [Elecraft] K3 Feature Req
Years ago in a land far far away we discontinued using the Semetra-Peak
(sp??) on AM in favor of the then new CBS Labs audio processers (
Audimax/Volumax (sp??)) which did a much better job of increasing the
average modulation with far fewer artifacts.
We did retain the boom mic phase reversal s
Good information on the Symmetra-Peak and phase rotation/scrambling
can be found here: http://www.w3am.com/8poleapf.html and a discussion
of AM symmetry with info on the "all pass filter" (phase rotation)
here: http://www.tonnesoftware.com/appnotes/allpass/allpass.html.
I suspect the rotation wou
transmitter site in San
Antonio before Waterman sold the stations for a much higher
calling in Ham Radio!
I coudda been a contendah on 3.625 with that box! :)
-lu-w4lt-
Message: 25
Date: Wed, 6 Oct 2010 09:55:06 -0400
From: "George & Jan"
Subject: Re: [Elecraft] K3 Feature Reques
The only change in f/w was to the S-Meter calibration on 144 Mhz. there
was no change in sensitivity and the gain of the K144XV is fixed in h/w.
We are revisiting the cal level for the S-Meter on 144 MHz.
73, Eric
www.elecraft.com
---
On 11/10/2010 5:36 AM, w...@comcast.net wrote:
> Now that th
Thanks Bill.
Under the 10Hz steps on the K3, I think the 1Hz digit is zeroed as soon as
the tuning knob is turned. You can check this by tuning to something other
than X.XX0, tapping the fine button, turning the knob and taping the fine
button again. Someone close to Elecraft may have a better u
The Smiths wrote:
> Actually Martin, I do use the RIT with the Split mode. Here's why:
>
> Some times when you're listening to the DX station, and other start
> transmitting on top of him,
> it's nice to RIT away from his beat Freq. up or down a little so that you
>can move the shift knob over
On Fri, 11 Jun 2010 11:16:31 +1000, "Jeff Cochrane - VK4BOF"
wrote:
Hi Jeff!
I also have the K144XV and find it to be a very good option. I'm
really glad I bought it and will probably put one in my other K3.
I too would like to see K70XV or K432XV.
If enough of us ask for one, perhaps Elecraf
I'll vote for a K222XV
73
K1NR
On Thu, 10 Jun 2010 22:29:14 -0500
Radio Amateur N5GE wrote:
> On Fri, 11 Jun 2010 11:16:31 +1000, "Jeff Cochrane -
> VK4BOF"
> wrote:
>
> Hi Jeff!
>
> I also have the K144XV and find it to be a very good
> option. I'm
> really glad I bought it and will probab
I'm not certain of this, but it seems to me that there is a difference,
in the settings for AGC THR and SLP that I need to be running,
for best weak signal reception on 160m compared to when I'm on 17m.
Is there something I'm missing as the operator,
or would it be possible to include those 2 sett
Er, try "xfil"? Or the "width" knob?
;)
73,
LS
W5QD
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-Feature-request-tp5204093p5204192.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft
On Mon, 21 Jun 2010 05:46:33 -0700 (PDT), Mike K2MK
wrote:
Even though it's a review, it sounds like marketing gibberish to me.
I get the same effect when using the .05 DSP CW filter in my 9 lb K3.
BT 73 ES GUD LUK
DE N5GE,
QCWA LIFE MEMBER 35102 AR SK
n...@n5ge.com
http://www.n5ge.com
>
>If
ady...
If you need further explaination please feel free to email me off the group...73
> Date: Mon, 21 Jun 2010 05:46:33 -0700
> From: k...@comcast.net
> To: elecraft@mailman.qth.net
> Subject: [Elecraft] K3 Feature request
>
>
> If you happened to read W3IZ'
> The contour...
>
> The reason I chose 400Hz is because unlike the contour which can variably
> move through the entire pass band area (600Hz - 900Khz) , with the K3 you
> only get a specific Freq. settings for each EQ setting.
In CW mode you also have DUAL PB which tracks your PITCH setting.
p...73
>
>
>
>
>
>
>> Date: Mon, 21 Jun 2010 05:46:33 -0700
>> From: k...@comcast.net
>> To: elecraft@mailman.qth.net
>> Subject: [Elecraft] K3 Feature request
>>
>>
>> If you happened to read W3IZ's review of the FTDX9000MP in the Ju
Hello All,
As a quick note, it would also be nice IF the frequency display would display
the TX freq, rather than the RX only.
73, Scott WA6LIE
K3 #1993
From: Bud Semon N7CW
Sent: Saturday, October 25, 2008 9:52 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] [K3] Feature Request
The
G'day Uli,
KEY OUT switches on tune on #345. That is how I tune my Acom 1000.
Regards,
Mike VP8NO
- Original Message -
From: "Ulrich Quandt"
To:
Sent: Thursday, January 08, 2009 6:47 PM
Subject: [Elecraft] K3 feature request
Hi folk,
i would like to have the ke
> - Original Message -
> From: "Ulrich Quandt"
> To:
> Sent: Thursday, January 08, 2009 6:47 PM
> Subject: [Elecraft] K3 feature request
>
>
> Hi folk,
>
> i would like to have the key out connector switched during ³Tune². That
> would be a
To:
> Sent: Thursday, January 08, 2009 6:47 PM
> Subject: [Elecraft] K3 feature request
>
>
> Hi folk,
>
> i would like to have the key out connector switched during ³Tune². That
> would be a
> use
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Ulrich Quandt
Sent: Thursday, January 08, 2009 4:16 PM
To: Mike Harris; elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 feature request
Hi Mike,
How is your firmware version ? I
Ouch.. that could blow the pin diodes or protection circuits in my
internal Ameritron PIN5 QSK switch if the amp were in the "Operate" mode
and RF were applied from the rig without the KEY line activated. It is
imperative that the KEY line be actuated before RF hits the amplifier
input to avoid
08, 2009 9:47 PM
To: 'Ulrich Quandt'; 'Mike Harris'; elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 feature request
I would like the key out not to switch on the amp when tuning the antenna
with a remote tuner without turning on the amp. That way when I operate the
amp i
The user would select via menu and front key use.
Bill
-Original Message-
From: Robert Naumann [mailto:w...@w5ov.com]
Sent: Friday, January 09, 2009 6:02 AM
To: 'Bill Johnson'; Elecraft@mailman.qth.net
Subject: RE: [Elecraft] K3 feature request
Just curious - how is the K3 s
A properly connected and adjusted ALC system that responds to
amp/antenna anomalies by signalling the rig to cut back on drive
might be useful. Don't know how it would respond to keying weirdness.
Jerry W4UK
At 05:57 1/9/2009, Mike Cox wrote:
>Ouch.. that could blow the pin diodes or protection
No PTT when tuning so it won't key the amp. Put it in the menu to switch
the PTT on or off?
Come on guys, why put this in the K3 or in any transceiver?
I really really don't understand why. If you are using an amp, set the
amp to standby. The K3 signal will go straight through. That's what it's
f
On Fri, 9 Jan 2009 18:07:26 +0100, you wrote:
>
>No PTT when tuning so it won't key the amp. Put it in the menu to switch
>the PTT on or off?
>
>Come on guys, why put this in the K3 or in any transceiver?
>I really really don't understand why. If you are using an amp, set the
>amp to standby. The
an.qth.net
Subject: [Elecraft] K3 feature request
Arnie: I have to agree with you. In the "old" days we used to call
it "going Barefoot". Every AMP has a STBY switch. I just checked
ALS-600 and sure enough it HAS one. I'm not one to advocate making
som
> "...Every AMP has a STBY switch. I just checked..."
Well...not every amp. My Alpha 70V has no standby switch. From the off
position, the amp either goes right into active CW or SSB operating mode --
with no warm-up time (the PA tube uses a directly-heated filament).
If I want to bypass
ensen
Sent: Friday, January 09, 2009 12:08 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 feature request
> "...Every AMP has a STBY switch. I just checked..."
Well...not every amp. My Alpha 70V has no standby switch. From the off
position, the amp either goes righ
#35; KX1 #35; K3 #1744; mini mods
>
>
> -Original Message-
> From: elecraft-boun...@mailman.qth.net
> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of K2ZLS
> Sent: Friday, January 09, 2009 11:45 AM
> To: ELECRAFT@mailman.qth.net
> Subject: [Elecraft] K3 fe
t; K9YEQ
> K2 #35; KX1 #35; K3 #1744; mini mods
>
>
> -Original Message-
> From: elecraft-boun...@mailman.qth.net
> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of K2ZLS
> Sent: Friday, January 09, 2009 11:45 AM
> To: ELECRAFT@mailman.qth.net
> Subject: [Elecraft]
On Fri, 9 Jan 2009 11:57:11 -0600
"Bill Johnson" wrote:
> Tony,
>
> Yes, the 600 has a standby switch. When changing bands and freqs frequently
> it would be useful not to go through a bunch of manual switching. Also
> consider that some of us may not have the amp in close proximity to opera
craft@mailman.qth.net
Subject: Re:Re: [Elecraft] K3 feature request
On Fri, 9 Jan 2009 11:57:11 -0600
"Bill Johnson" wrote:
> Tony,
>
> Yes, the 600 has a standby switch. When changing bands and freqs
frequently
> it would be useful not to go through a bunch of manual switching
On Fri, 09 Jan 2009 14:58:52 -0700
David Gilbert wrote:
>
>
> Did you get a reduced rate on exclamation marks or something? No need to
> shout every
>sentence
>
> Dave AB7E
>
>
>
> JIM DAVIS wrote:
>> HMMM!
>>
>> For some of the features that are not well apparent while us
> Be a really nice touch in the K3 if I can choose whether or
> not headphone insertion mutes the internal (or external) speaker.
This was discussed at length among the Field Testers a week or so back. As
you suggest, the capability will probably be available via a menu setting
since many people
J. Edward (Ed) Muns wrote:
Be a really nice touch in the K3 if I can choose whether or
not headphone insertion mutes the internal (or external) speaker.
OOH, yes please, this would be great :-)
Ian
--
Ian J Maude G0VGS
SysOp GB7MBC DX Cluster
Member of RSGB, ARRL, GQRP
K2 #4044 | K3 #?
__
On Tue, 17 Jul 2007, Don Rasmussen wrote:
There will be great interest throughout the life of
the K3 product from users about which specific
features or fixes are on the "to be added list", the
relative priority, and when they might become
available. !!!
Once the developers get over the shell-
> Be a really nice touch in the K3 if I can choose whether or not
> headphone insertion mutes the internal (or external) speaker.
This is functionality that is useful to me! If it is menu selectable its
even better.
73 de Björn /SM0MDG
___
Elecraft
Once the developers get over the shell-shock, they might want to
setup an application on the web page that lets them, and the users
keep track of it.
That's a good idea. I've always been a strong believer in the maxim
that "if it ain't broke, don't fix it" (one reason why K2 #392 is
largely unmo
On Wed, 18 Jul 2007, Julian G4ILO wrote:
Once the developers get over the shell-shock, they might want to
setup an application on the web page that lets them, and the users
keep track of it.
That's a good idea. I've always been a strong believer in the maxim
that "if it ain't broke, don't fix
- N6KR, Elecraft
Subject: [Elecraft] [K3] Feature Request
If you activate Noise Reduction (NR) on a mode (like CW), NR is on for all
modes on that band. Request NR to follow both mode and band. For example,
if you have NR selected for 40m CW, and change to LSB, NR is OFF (unless
previously
I am curious what you are you using the memories for? I really never
noticed any delay but during 300/hour rates I think it is way easier to
just to speak.
John KK9A
charlie carroll k1xx at k1xx.com
Fri Mar 11 13:12:02 EST 2016
I use the internal K3 message memories when operating as DX in an
Did you try turning the VOX Delay down to zero?
Worked for me when running remotely!
73 Dwight NS9I
On 3/11/2016 1:12 PM, charlie carroll wrote:
I use the internal K3 message memories when operating as DX in an ssb contest.
One of the biggest problem I face is the delay both in initiating the
I think SPLIT SV does this. It should preserve your RIT and XIT
settings on a per-band basis. You'll find the setting at
CONFIG:SPLT SV.
73,
matt
W6NIA
On Wed, 04 Feb 2015 16:00:17 -0800, you wrote:
>Would it be possible to have an option that will either work the way it
>does now, or wil
QTA my "feature request." Thanks Matt, exactly what I was looking for.
73,
Fred K6DGW
- Northern California Contest Club
- CU in the 50th Running of the Cal QSO Party 3-4 Oct 2015
- www.cqp.org
On 2/4/2015 4:31 PM, Matt Zilmer wrote:
I think SPLIT SV does this. It should preserve your RIT an
Sticky timer; turn the K3 on at a set time each day.
Rick WA6NHC
Smell Czech correction happens
> On Apr 6, 2019, at 2:12 PM, Dick Dickinson wrote:
>
> Sticky Noise Blanker.through on/off cycle and band changes.
>
>
>
>
>
> Dick - KA5KKT
>
> _
Neat idea, Hank!
On Fri, Jul 1, 2011 at 4:23 PM, W6SX Hank Garretson wrote:
>
> It would be wonderful if there were a CONFIG option to have CWT SPOT
> zero beat using RIT instead of VFO A. This would be very useful
> during contests when CQing.
>
>
--
Rick Tavan N6XI
Truckee, CA
__
Sent: Saturday, July 02, 2011 11:54 AM
To: W6SX Hank Garretson
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 Feature Request
Neat idea, Hank!
On Fri, Jul 1, 2011 at 4:23 PM, W6SX Hank Garretson wrote:
>
> It would be wonderful if there were a CONFIG option to have CWT SPOT
>
Why would you want this?
On Thu, 2011-01-27 at 21:30 -0500, Edward Dickinson, III wrote:
> 10 Minute Timer - Sound, 'Beep, Beep, Beep.' Alternate, Flash or Dim
> Display and/or Panel Lights. Reset Timer. Countdown on clock display.
>
> 73,
--
73
Brendan EI6IZ
___
-Original Message-
From: Edward Dickinson, III [mailto:edd...@windstream.net]
Sent: Thursday, January 27, 2011 9:50 PM
To: 'elecraft@mailman.qth.net'
Subject: Re: [Elecraft] K3 Feature Request
...as a reminder for requisite station identification.
73,
Dic
You're kidding, right?
On 1/27/2011 7:30 PM, Edward Dickinson, III wrote:
> 10 Minute Timer - Sound, 'Beep, Beep, Beep.' Alternate, Flash or Dim
> Display and/or Panel Lights. Reset Timer. Countdown on clock display.
>
>
> 73,
> Dick - KA5KKT
>
>
> ___
I sure hope so!
Gary
On Fri, Jan 28, 2011 at 5:34 PM, David Gilbert wrote:
>
> You're kidding, right?
>
>
>
> On 1/27/2011 7:30 PM, Edward Dickinson, III wrote:
>> 10 Minute Timer - Sound, 'Beep, Beep, Beep.' Alternate, Flash or Dim
>> Display and/or Panel Lights. Reset Timer. Countdown on cl
No.
73,
Dick - KA5KKT
-
David Gilbert wrote:
You're kidding, right?
On 1/27/2011 7:30 PM, Edward Dickinson, III wrote:
> 10 Minute Timer - Sound, 'Beep, Beep, Beep.' Alternate, Flash or Dim
Behalf Of Edward Dickinson, III
Sent: Friday, January 28, 2011 8:22 AM
To: Elecraft Reflector
Subject: Re: [Elecraft] K3 Feature Request
No.
73,
Dick - KA5KKT
-
David Gilbert wrote:
You&#x
I like the CW text decode feature, but only use it on my transmissions
(TX ONLY) to see how my sending is doing. I like that when using TX
ONLY the AGC doesn't go to AGC-S. I don't like that the display keeps
switching back to VFO B between words. Very distracting.
If set to CW 5--40, the di
Hi Sam,
I often thought about this as well.
Since the noisefloor is generally much higher on the lower bands, it would
be nice if AGC threshold or RX IF gain could be scaled in relation to
bandnoise levels.
To do this you would need to use a table with a few setting points across HF
and have ga
Then one starts getting into trouble with using RX antennas with low
gain, where the RX gain and pre usage IS appropriate. The FT1000MP
*DID* have the de-emphasis you speak about. Over about a decade of
usage, I wound up turning the de-emphasis off more than not, for use
on RX antennas.
The Orio
Guy,
I can't follow the comparison with the Querty keyboard, sorry.
>>Some things better left
alone.
Or given the option "enable/disable" .
73'
Paul
PD0PSB
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-feature-request-query-tp5186033p5186952.html
Sent from t
Ah, okay Mike, I missed that this was already "universally rejected" by
everybody...
I assumed TenTec and Yeasu tried to implement this for a good reason, but
weren't succesfull, and I had the illusion Elecraft could be the first to
come up with a good solution.
But ofcourse I won't stand up to
On Thu, 17 Jun 2010 02:27:39 -0700 (PDT), pd0psb wrote:
In line...
>
>Ah, okay Mike, I missed that this was already "universally rejected" by
>everybody...
>
>I assumed TenTec and Yeasu tried to implement this for a good reason, but
>weren't succesfull, and I had the illusion Elecraft could be t
Could the state of the Menu's be left at last position when turning the rig
on and off? Right now it appears they revert back to the beginning. I
would like to resume where I left off when I turn the rig on.
73,
Bill
K9YEQ
___
Elecraft mailing list
Hey troops,
I had an idea last night while in CW QSO with my K3. I've noticed that
I always turn the AF gain down when I send CW. I have the side tone
volume set to just the right level for the Spot function to work, but
when I send CW I want to greatly reduce the distraction from the
receiver.
I use 0 through 9 on the K2 and K3 as permanent "jump to band;
configure appropriately" memories. This normally works great, but I have a
frustrating habit of accidentally pressing STORE or V->M when I mean to
press RCL or M->V, and there go my settings. I'm not expecting a K2
update :)
While we're talking about feature requests for the K3,
I'd like to have the possibility to have the text decode in the vfoB
area stay there, and not quickly return to displaying frequency as soon
as the other station stops transmitting. An additional entry for the
DISP menu should be ok. If this f
We originally did this, Bill, but here's the problem. Those new to the
K3 sometimes forget that VFO B scrolls the menu entry and VFO A
modifies the parameters. If the last-selected menu entry is in effect
on power-up, you can inadvertently change something important by
spinning VFO A. We initia
Wayne,
Thank you for the info.
Makes sense to leave it where it is. There is so much to learn with rigs
these days it can be difficult to remember it all. I cannot tell you how
much I appreciate the quality of the radio. I haven't turned on my other HF
equipment because of the K3. (I do use t
dward Dickinson, III
Sent: Monday, June 15, 2009 12:51 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 Feature Request
Experience has shown me that I can more easily tune to a desired frequency
that is 'kHz.000' without the visual distraction of the 10Hz digit. Is it
possible to c
Hi Bill and thanks for the reply.
I'd like tuning as usual in 10 kHz steps, but would like to able to shut off
the display of the 10Hz digit.
Best regards,
Dick - KA5KKT
-
-Original Message-
I tune to Khz.zero's and then use the Fine/
Edward Dickinson III wrote:
>
> Hi Bill and thanks for the reply.
>
> I'd like tuning as usual in 10 kHz steps, but would like to able to shut
> off
> the display of the 10Hz digit.
>
>
But if the 10Hz (and 1Hz for that matter) digits are actually not zero then
the radio would be displaying
I like that idea.
73,
Bill
K9YEQ
K2 #35; KX1 #35; K3 #1744; mini mods
ATS-3B
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Julian, G4ILO
Edward Dickinson III wrote:
>
> Hi Bill and thanks for the reply.
>
> I'd like t
Hi Bill,
Me too!
73 QRO de Rudolf, HB9ARI
K3#1212
Bill K9YEQ wrote:
> I like that idea.
>
> 73,
>
> Bill
> K9YEQ
> K2 #35; KX1 #35; K3 #1744; mini mods
> ATS-3B
>
> -Original Message-
> From: elecraft-boun...@mailman.qth.net
> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Julia
andwidth and open up
the bandwidth to 500 Hz or so after a delay set by the semi-QSK delay?
73,
Erik K7TV
- Original Message -
From: Darwin, Keith
To: elecraft@mailman.qth.net
Sent: Tuesday, January 20, 2009 5:47 AM
Subject: [Elecraft] K3 feature request - I want Ducking!
Hey
What is "ducking", as you call it here?
73! Ken Kopp - K0PP
elecraftcov...@rfwave.net
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
Ducking is a commercial radio / sound industry technique of attenuating
the music when the DJ talks. In the old days, the DJ at the radio
station would just pan down the music volume whenever he spoke into the
mic. These days, recording studios will use a compressor with a
separate trigger (side
I still don't understand this notion. For CW, don't you obtain this
effect simply by turning down the sidetone volume? On transmit,
receive is already muted.
Peter
On 1/20/09, Darwin, Keith wrote:
> Ducking is a commercial radio / sound industry technique of attenuating
> the music when t
1 - 100 of 182 matches
Mail list logo
