I am using a Flex 3000 radio with PSDR 2.0.22. I am also trying to use
JT65-HF version 1.07. I can answer a CQ by double-clicking on the
green message, but at the end of the transmission, the MOX button in
PSDR stays lit, and I cannot get it to go off, except by closing
PSDR.I am using
We need more info. What operating system and virtual com port software are you
using?
I'd remove any ancillary layers of software by eliminating the HRD component
and just use JT65-HF with PowerSDR. HRD keeps coming up repeatedly and has
such for a very long time as a key commonality with
Hello Graham,
Looking on the specs of my Isotemp 134-10 oscillator showed that spurious
attenuation should be 60 dB. Looking at the 10 MHz signal on the 1500
showed a lot of spurii about 60 dB down. In my scrapbox I found a 10 MHz
8-pole quarzfilter. Putting this filter in line with the 10 MHz
Tim,
I am using Windows 7 and VSP Manager, version 1.0.1.017.I was trying
to use the same COM port as PSDR has listed for the PTT port, and I
guess one of these days I will remember to use the opposite number in
the pair. I can now make the PTT work, but even with or without
Kjeld:
Any sidebands or trash on your 10 MHz reference, that are within the
bandwidth of
the Phase Lock Loop reference multiplier in the DDS will appear on the local
oscillator
in the 1500. Which means that they will appear on both transmitted and
received signals.
Analog devices does not
Hello,
I have one new Syba Fireware card (PCI) which I don't need. It is recommended
for the FLEX-5000A/3000 - uses the Lucent AGERE FW323 chipset
More info:
http://kc.flexradio.com/KnowledgebaseArticle50179.aspx
Please contact me of the list if you need one... EU desirable
SRI for the
Got MixW on and recieves great but no transmit . VAC is good and input
,output seems right ... Flex 1500 here
Thanks !!!
George , N2JNZ
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
Hi
What version of VAC and MixW?
What is TX audio level set to.
Are you in Digu or USB?
Answers will help diagnosis.
Keith
Sent wirelessly from my BlackBerry device on the Bell network.
ke...@goobie.org
-Original Message-
From: gos...@twcny.rr.com
Sender:
Another question. What is your com port setup. Are you using com0com or VSP?
Are you trying to use CAT control?
Keith
Sent wirelessly from my BlackBerry device on the Bell network.
ke...@goobie.org
-Original Message-
From: Keith Goobie ke...@goobie.org
Sender:
I have been using PSK 31 with no problems using FLEX versions 19 through 22
I installed the virtual audio ports and the serial port as shown in the manual
with no problems
In using PSK with digipan I set my VAC , my Didgu and set my transmit and
receive sliders to half way.
Also be sure to set
Gary
I struggled with this also, and eventually just removed everything from the
chain except JT65-HF:
1. I set the PSDR COM port to PTT and selected on COM3
2. I set JT65HF to control the rig on COM13
3. I set VSPMgr to pair COM3 with COM13
4. I turned off HRD, disabled all other COM inputs
Mark,
That is exactly where I am at right now. I will keep poking around and
see if I can get the two programs to recognize each other sufficient to
synchronize the frequencies.
Gary
WG1I
On 4/13/2011 12:38 PM, Mark Lunday wrote:
Gary
I struggled with this also, and eventually just
I've not posted in a while since I've had no recent problems since the
upgrade to v. 2.0.19, but I've just suddenly discovered terribly distorted
audio with an echo as well back in SSB mode. I had this problem months ago
with an earlier version and got help solving it. I checked levels and only
PowerSDR v2.0.22
Flex-3000
Windows 7 64
3.0ghz Athlon Phenom II X4
4 gigs memory
Running WSPR at 2 watts my Power/SWR Meter shows 2 watts out PowerSDR
shows Fwd Pwr 0 watts.
TX gain is set to -7 Drive is set to 7 to give 2 watts output on my
meter. MODE is DIGU
Steven
--
Sent from my Linux
If you make the upgrade to the latest version (2.0.22) you will enjoy
the sweet fruit of better CW assuming you have a FLEX-xx00 SDR (the CW
changes are not applicable to the SDR-1000)
Also feedback and echo are usually indicative of RF in the Firewire
cable or the mic cable.
-Tim
---
W4TME
I am not sure exactly what you are asking, but when working split, VFO-B
displays the transmit frequency and it will be red (along with the TX
button in the VFO display) indicating that it is the transmitting only
VFO. No mater what the width of the split.
See pages 60-61 and 78 of the
Dave,
You wrote, Is that because the split is so big or ???
Yes, that is correct. Apparently, you had MultiRX turned on. Turn it off
you can do it.
The problem is that in order for MultiRX to work, both frequencies must be
visible in the Panadapter at the same time. So, if you have a wide
As the owner of an SDR-1000 this makes me sad. But I do understand.
Edwin Marzan AB2VW
Date: Wed, 13 Apr 2011 22:05:54 -0400
From: t...@flex-radio.com
To: rjl...@gmail.com; flexradio@flex-radio.biz
Subject: Re: [Flexradio] Audio Distortion
If you make the upgrade to the latest version
IIRC, the recent CW changes were made to the firmware inside the FLEX
radios. The SDR-1000 has no firmware inside (which is actually a
benefit when you want to switch around among the various editions of PowerSDR).
Jerry W4UK
At 10:23 PM 4/13/2011, you wrote:
As the owner of an SDR-1000
19 matches
Mail list logo