Not that I've seen. It still seems to be under NDA. On Tuesday, February 16, 2021 at 8:57:41 AM UTC-8 se...@bitkickers.us wrote:
> Is the API documented online somewhere? I've not been able to find is so > far. > > On Tuesday, February 16, 2021 at 7:41:36 AM UTC-8 se...@bitkickers.us > wrote: > >> If 'reset' does a factory reset, I think I agree with you - not too much >> value in that for me. OTOH, being able to reboot remotely, at least in my >> case, might be a benefit. >> >> While I understand the ability of Weewx and the GW1000 driver to attempt >> to reconnect to the gateway. Unfortunately, that doesn't solve the problem >> if it's alive but unresponsive. >> >> Thanks for the reply. >> >> Sean >> On Monday, February 15, 2021 at 8:51:52 PM UTC-8 gjr80 wrote: >> >>> Can't speak for Monit, haven't used it and only briefly skimmed an >>> article on it a year or two back. Whilst the GW1000API has commands to >>> reset and reboot the device I have not implemented them int he GW1000 >>> driver and I have been loathed to do so. I really don't see much point in >>> giving the driver the ability to factory reset the GW1000; if the device is >>> factory reset you need to use the WS View app to pair/configure the device >>> again so you might as well goto the device or use the WS View app to >>> factory reset if such action is warranted. I could see some utility in >>> being able to reboot the GW1000, but I suspect that in almost all >>> situations where you would want to take such action you have lost contact >>> with the GW1000 and I doubt you will be able to command the GW1000 to >>> reboot via the API. >>> >>> That being said WeeWX and the GW1000 driver have a couple of features >>> that attempt recovery if contact with the GW1000 is lost. Firstly, if a >>> driver cannot be loaded WeeWX has the ability to keep trying to load the >>> driver every 60 seconds rather than exiting (refer loop_on_init config >>> option <http://weewx.com/docs/usersguide.htm#General> in weewx.conf). >>> Secondly, if the GW1000 driver cannot contact the GW1000 on startup, or if >>> contact is lost during normal operation, the driver re-attempts contact a >>> number of times and if contact cannot be made the driver will attempt to >>> re-discover the GW1000 on the network. These may or may not work depending >>> on the issue, the log would be need to be checked to see what the symptoms >>> were and what WeeWX/the driver did. >>> >>> Ultimately if the GW1000 cannot be contacted and cannot be discovered >>> then there is not much that can be done short of notifying you to go and >>> hit the reset button. >>> >>> Gary >>> >>> On Tuesday, 16 February 2021 at 11:56:49 UTC+10 se...@bitkickers.us >>> wrote: >>> >>>> Not bothering to post logs, etc., because this isn't a "problem" with >>>> the software. >>>> >>>> Been using Weewx for a few years with Acurite 01525 but finally got fed >>>> up with the horribly flaky RF from sensors to console and recently >>>> transitioned to Ecowitt and the GW1000 with temp, wind, and rain sensors. >>>> Loving it so far although the WS View app on Android apparently had a bug >>>> that initially prevented me from configuring the gateway properly. Kudos >>>> to >>>> the Ecowitt team who were very responsive (sup...@ecowitt.com). >>>> >>>> Browsing the weewx-user group I found >>>> https://github.com/gjr80/weewx-gw1000 and that's a delightful piece of >>>> code, every bit as good an useful as Weewx itself. >>>> >>>> The gateway has gone offline a couple of times in the past 48 hours for >>>> reasons unknown. Its leds are flashing as if it's online, and it can >>>> sometimes be pinged so it's on the wlan, but it doesn't respond to API >>>> requests for the driver. I'd like to monitor the gateway from a monit >>>> server that I have running on my network and while I can test for the host >>>> alive and send an alert, I'd really like to monitor the gateway function >>>> itself somehow. >>>> >>>> If it were a linux box under the covers and had access, I could script >>>> a solution on the gateway itself but I don't think that's possible. I note >>>> in the GW1000 driver that the command list has a "reset" and "reboot" >>>> command and wonder if the driver will allow me to send either one of those >>>> by itself? >>>> >>>> Any other suggestions? >>>> >>>> Thanks! >>>> >>>> Sean >>>> >>> -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/44928e81-b98e-48ca-a09c-ab9450c61c04n%40googlegroups.com.