Check your menu for this option
CAT control shows being able to change the rig config to select RTS or DTR for
DATA SEND too.
Mike W9MDB
On Monday, July 19, 2021, 05:25:13 PM CDT, Conrad PA5Y via wsjt-devel
<wsjt-devel@lists.sourceforge.net> wrote:
So why does the WSJT-x software work exactly as I want using the USB codec in
and out on the K3S? Is it because in the K3S CAT commands there is no
possibility to use transmit audio source and so therefore it does not matter?
I can key the K3S using the PTT or CAT and still have USB audio.
I have full CAT control and use RTS for PTT. This keys the rig and the TX audio
goes via the internal USB audio codec. Just like I want it to. It would be more
flexible to let the user choose what happens. However Kenwood have decided to
disable the USB input if the SS (PTT) is used. There is no way that I can see
to use non-CAT PTT and USB Audio in the TS-890S configuration. This is an
oversight by Kenwood. The rig has hundreds of options but using PTT via the
accessory socket while still using USB audio is not one of them.
Currently I am using audio from a UMC202HD soundcard via the ACC2 socket, I
really did not want to do that. I do not like to use CAT PTT to drive the
sequencer, but I may have to. It is far better to have the RF drive go over
last – always.
Anyway, it seems that WSJT-X is behaving correctly and that the TS-890S has
limitations. So wrong email reflector.
73
Conrad PA5Y
From: Bill Somerville via wsjt-devel <wsjt-devel@lists.sourceforge.net>
Sent: 19 July 2021 23:13
To: wsjt-devel@lists.sourceforge.net
Cc: Bill Somerville <g4...@classdesign.com>
Subject: Re: [wsjt-devel] very infuriating problem with Hamlib for TS-890S
On 19/07/2021 19:19, Conrad PA5Y via wsjt-devel wrote:
Probably best if I add a few snips. The first configuration works perfectly.
However, in this mode using USB you must select Rear/Data as the TX audio
source. I wish to use the REMOTE SOCKET PTT as the radio goes over last from a
sequencer as is often the case for VHF ops. I have always run this way. BUT the
Transmit audio source is disabled when you use RTS. The PTT works but I can no
longer access the USB input, this is a BIG problem for me. Why can I not select
the transmit audio source?
I think that this is a HAMLIB bug. How long does it take to fix these things
generally as I assume that this is a Hamlib problem?
Regards
Conrad PA5Y
Conrad,
it seems you have not understood the purpose of the transmit audio source
option in WSJT-X. It is available for rigs like the TS-890s which have a CAT
PTT command (TX) that has two variants to select the Tx audio source. If you
are not using CAT PTT then WSJT-X via Hamlib cannot use the TX CAT command,
because you have explicitly told it not to.
Regardless of the above, the pin you to key the rig also has the same function,
if you use the PTT pin then the audio source is the mic socket, if you use the
PKS pin on the ACC socket then the Tx audio source is the PKD pin on the same
socket.
So in summary, it is down to you to wire the PTT to the correct pin on the rig,
neither WSJT-X nor Hamlib can do that for you!
73
Bill
G4WJS.
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
