GigE-APC-HV has different wiring than a 430-APC-HV. One of them is going to short out the POE.
From: Forrest Christian (List Account) Sent: Thursday, October 29, 2015 1:21 PM To: af Subject: Re: [AFMUG] PMP450i lack of gigabit Which injector are you using? On Oct 29, 2015 11:05 AM, "Matt" <matt.mailingli...@gmail.com> wrote: > > I have mine set on 1000base and it will only do 100base. It tries to do > 1000base at first, you can see the dlink managed switch light blink green at > first, then it gives up and goes too 100base. It passes through 200 foot of > shielded cat-5 then a GigE-APC-HV. I have also tried a 430APC-HV with same > result. > > > On Thu, Oct 29, 2015 at 11:28 AM, Josh Luthman <j...@imaginenetworksllc.com> > wrote: >> >> Not a stupid question, George. That was it. >> >> Factory default is actually the second to last option - auto 100/10/f/h. I >> mean config from the factory - not what happens if you push factory default >> in software. I did take this radio from 14.0 (factory) to 14.1b6. >> >> >> Josh Luthman >> Office: 937-552-2340 >> Direct: 937-552-2343 >> 1100 Wayne St >> Suite 1337 >> Troy, OH 45373 >> >> On Thu, Oct 29, 2015 at 7:20 AM, Forrest Christian (List Account) >> <li...@packetflux.com> wrote: >>> >>> Good catch... My testing 450i seems to default to gigabit off (after a >>> factory default). >>> >>> Once I set it on (which I seem to remember doing previously as well), it >>> links right up at gigabit speeds. This is with a RB850Gx2 >>> >>> -forrest >>> >>> >>> >>> >>> >>> >>> On Wed, Oct 28, 2015 at 5:32 PM, George Skorup <geo...@cbcast.com> wrote: >>>> >>>> Stupid question.... Does the 450i have this like 13.x on the regular 450? >>>> Default is auto 100f/100h/10f/10h. >>>> >>>> >>>> >>>> On 10/28/2015 4:37 PM, Josh Luthman wrote: >>>>> >>>>> I wonder if this unit is capable of doing gigabit with 450i? It does >>>>> gigabit on the ePMP. >>>>> >>>>> >>>>> Josh Luthman >>>>> Office: 937-552-2340 >>>>> Direct: 937-552-2343 >>>>> 1100 Wayne St >>>>> Suite 1337 >>>>> Troy, OH 45373 >>>>> >>>>> On Wed, Oct 28, 2015 at 5:36 PM, Matt <matt.mailingli...@gmail.com> wrote: >>>>>> >>>>>> > I have a PacketFlux SyncInjector Gigabit that goes to the 450i. It's >>>>>> > got a >>>>>> > 48v power supply. There is no syncpipe, nor would anything work in >>>>>> > the lab. >>>>>> > The test PC has two Intel gigabit NICs. >>>>>> > >>>>>> > My issue is that I can only get a 100 Mbit here. >>>>>> > >>>>>> > I have it set to generate sync right now and I can access it just >>>>>> > fine. If >>>>>> > I have it set for autosync + free run I get some problems accessing the >>>>>> > device (ping works for a few seconds on, then off, web interface is not >>>>>> > responsive at all, CNUT flat out doesn't work). The ethernet link >>>>>> > does not >>>>>> > go down/up with sync at all. >>>>>> > >>>>>> > Any other clues or things to look at? >>>>>> >>>>>> FYI, I am seeing same thing. It passes through a GigE-APC-HV on way >>>>>> to 450i AP. AP is getting sync from daisy chained syncpipe source >>>>>> hooked too Gigabit SyncInjector powered by 48 volt. AP is working >>>>>> fine just at 100mbps ethernet. >>>>> >>>>> >>>> >>> >>> >>> >>> -- >>> Forrest Christian CEO, PacketFlux Technologies, Inc. >>> Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 >>> forre...@imach.com | http://www.packetflux.com >>> >>> >> >
