Do you get the calculated rx-power?
Von: Af [mailto:af-boun...@afmug.com] Im Auftrag von Faisal Imtiaz Gesendet: Donnerstag, 21. Juli 2016 20:33 An: af@afmug.com Betreff: Re: [AFMUG] Metrolinq It would be appropriate to point out that there are two versions or Metrolinq 60ghz Radios one smaller lower power and other larger higher power. We have been using the larger units (Circular cones) for links 250m to 450m successfully.. aiming them with the shipping brackets is a whole another challenge.. I am very happy to the the LR brackets available and those should go long ways is aligning longer links. . Faisal Imtiaz Snappy Internet & Telecom 7266 SW 48 Street Miami, FL 33155 Tel: 305 663 5518 x 232 Help-desk: (305)663-5518 Option 2 or Email: supp...@snappytelecom.net <mailto:supp...@snappytelecom.net> _____ From: "Carl Peterson" <cpeter...@portnetworks.com <mailto:cpeter...@portnetworks.com> > To: af@afmug.com <mailto:af@afmug.com> Sent: Thursday, July 21, 2016 11:57:41 AM Subject: Re: [AFMUG] Metrolinq We haven't had any issues with 5GHz but the 60GHz side underwhelms. We tried a 900' link and couldn't get the 60Ghz side to work. We were able to move one end and get it down to 600' and have a 60GHz link at -55 but that is 10-15db below where it should be. It's working, but at this point I wouldn't use it for anything over 500' or so. On Thu, Jul 21, 2016 at 10:40 AM, Stefan Englhardt <s...@genias.net <mailto:s...@genias.net> > wrote: We’ve only dfs bands in 5 GHz. Metrolinq supports only the lower band with lower allowed power (1W EiRP). I’ve installed the newest FW before doing anything so I might be lucky to avoid the biggest problems (hopefully). Von: Af [mailto:af-boun...@afmug.com <mailto:af-boun...@afmug.com> ] Im Auftrag von Faisal Imtiaz Gesendet: Donnerstag, 21. Juli 2016 16:30 An: af@afmug.com <mailto:af@afmug.com> Betreff: Re: [AFMUG] Metrolinq Interesting.. most folks have the opposite issue. FWIW, there is no dfs support on 5ghz (not sure about non-american rules). If you are bench testing... you need to turn down the power on 5ghz .. way down.... Regards Faisal Imtiaz Snappy Internet & Telecom 7266 SW 48 Street Miami, FL 33155 Tel: 305 663 5518 x 232 <tel:305%20663%205518%20x%20232> Help-desk: (305)663-5518 <tel:%28305%29663-5518> Option 2 or Email: supp...@snappytelecom.net <mailto:supp...@snappytelecom.net> _____ From: "Stefan Englhardt" <s...@genias.net <mailto:s...@genias.net> > To: af@afmug.com <mailto:af@afmug.com> Sent: Thursday, July 21, 2016 8:13:34 AM Subject: [AFMUG] Metrolinq Got my first links. 60GHz work fine in lab. The 5GHz Part does strange things. Does not initialze or does not connect. Syslog gives dfs or cant initialize messages. 60GHz is up immediately und runs stable in lab. Latency is low. Feels like a 1G cable connection. Powered by Netonix 24V. Takes only 6 Watts. Good build quality. Webinterface is easy and fast. So a cheap option for fast short hops where you dont want to dig. -- Carl Peterson PORT NETWORKS 401 E Pratt St, Ste 2553 Baltimore, MD 21202 (410) 637-3707
