Yes... if I read the original post right, the radio is currently only
putting out 24dbm, and he wants to increase it to 27dbm - if you can have
26dbm conducted power at the antenna (which is what I've always assumed,
and I believe what the UBNT gui normally allows) you would only need 1db of
cable loss.

On Fri, Jul 29, 2016 at 4:15 PM, Ken Hohhof <[email protected]> wrote:

> I don’t follow your math.
>
> The most likely interpretation is that conducted power is at the antenna
> end of the cable, so if you have 1 dB of cable loss, you can increase radio
> xmt power 1 dB to compensate.
>
> The other interpretation would be that cable loss subtracts from antenna
> gain.  So if you have 1 dB of cable loss, then in effect you have 1 dB less
> antenna gain, and can increase xmt power by 1/3 of a dB.
>
> Oh, one more thing, make sure you aren’t getting caught in the difference
> between aggregate vs per stream power levels.  UBNT products are pretty
> clear about this in the GUI though.
>
>
> *From:* Mathew Howard <[email protected]>
> *Sent:* Friday, July 29, 2016 3:56 PM
> *To:* af <[email protected]>
> *Subject:* Re: [AFMUG] UBNT AF-2X Problems... Where Do You Go For Help?
>
> I'm pretty sure that you could increase transmit power to compensate for
> cable loss, which would mean you'd only need 1db of cable loss to be able
> to up the transmit power by 3db... and anything that's being called "long
> cables" is almost certainly going to be more than 1db.
>
> On Fri, Jul 29, 2016 at 2:27 PM, Ken Hohhof <[email protected]> wrote:
>
>> Is this in FCC area?  FCC rules for 2.4 GHz PTP are 30 dBm max
>> transmitter power with 6 dBi antenna, for a total +36 dBm EIRP.  Then for
>> antenna gain above 6 dBi, you have to reduce xmt power 1 dB for every
>> additional 3 dB of antenna gain.  Also this is independent of channel
>> width, it’s not dBm/MHz.
>>
>> So you have an 18 dBi dish, that’s 12 dBi of additional antenna gain, so
>> you would have to reduce xmt power by 1/3 of 12 dBi or 4 dB, to +26 dBm,
>> and max EIRP would be +42 dBm.
>>
>> How many dB do you figure you’re losing in the long cables?  I’m unclear
>> on whether cable loss counts against xmt power or antenna gain.  If you’re
>> losing several dB in the cable, I can see where you’d want the full +30 dBm
>> xmt power from the radio.
>>
>> *From:* Christopher Gray <[email protected]>
>> *Sent:* Friday, July 29, 2016 1:20 PM
>> *To:* [email protected]
>> *Subject:* [AFMUG] UBNT AF-2X Problems... Where Do You Go For Help?
>>
>> I've had an open ticket about the AF-2X for over a month. I have not been
>> able to actually work with anyone on the issue. It has been "escalated" but
>> without any positive results.
>>
>> Is there a better way to talk to someone about the airFiber?
>>
>> The spec sheet says a US AF-2X has a maximum Tx power of 30 dBm... but it
>> only goes up to 24 dBm. [I'm running an 18 dBi dish on one end with long
>> cables, and I need the additional 3 dB Tx power). When changing channel
>> width, the Rx power does not change (Rx power is usually measured in
>> dBm/20Hz on most UBNT hardware, so power usually goes up 3 dB when halving
>> the bandwidth, but I can't get a straight answer as to whether they use the
>> same units on the AF line).
>>
>> Long story short, I'm going to have to get rid of this AF-2X hardware and
>> switch back to ePMP. The AF-2X would be the better choice if I could get
>> the power levels I need to make this link work. I would much rather solve
>> the AF problems..
>>
>> -Chris
>>
>>
>
>

Reply via email to