I've seen on a 1036-2S+ where the route table doesn't reflect changes for 10 
minutes (via the filter in IP Routes) and then where traffic doesn't actually 
change course for another 10 minutes after that. 

That's not good. 




----- 
Mike Hammett 
Intelligent Computing Solutions 

Midwest Internet Exchange 

The Brothers WISP 




----- Original Message -----

From: "Mike Hammett" <[email protected]> 
To: [email protected] 
Sent: Tuesday, May 9, 2017 6:36:26 AM 
Subject: Re: [AFMUG] rb1100ahx2 bgp load 


If it's eating the entire core (which it is), it isn't doing fine. You're not 
having timely route convergence. 


On the 1100AHx2 vs. 1100AHx4: 
https://www.facebook.com/thebrotherswisp/posts/1200772160048234 




----- 
Mike Hammett 
Intelligent Computing Solutions 

Midwest Internet Exchange 

The Brothers WISP 




----- Original Message -----

From: "Stefan Englhardt" <[email protected]> 
To: [email protected] 
Sent: Tuesday, May 9, 2017 6:29:56 AM 
Subject: Re: [AFMUG] rb1100ahx2 bgp load 

Works quite well and very stable on the bigger CCR models (memory). We use 
2x CCR1036-8G-2S+. 
Eating one of the cpus for the bgp process. 1100AHx2 cpu is a bit slow. 
There is a newer 1100AHx4 
which is twice as fast as 1100AHx2. 

Mikrotik BGP Routers are holy cows. There are no updates/config changes at 
normal times. 

On Tue, 9 May 2017 11:20:30 +0000 
Mike Hammett <[email protected]> wrote: 
> I hear there are some versions better than others in 
>terms of BGP performance, but Mikrotik BGP really belongs 
>on x86 boxes until v7 is out. 
> 
> 
> 
> 
> ----- 
> Mike Hammett 
> Intelligent Computing Solutions 
> 
> Midwest Internet Exchange 
> 
> The Brothers WISP 
> 
> 
> 
> 
> ----- Original Message ----- 
> 
>From: "[email protected]" 
><[email protected]> 
> To: [email protected] 
> Sent: Tuesday, May 9, 2017 5:59:50 AM 
> Subject: Re: [AFMUG] rb1100ahx2 bgp load 
> 
> 
> 
> Take a look at /tool profile (on in Winbox) to see where 
>the CPU load is going. It is 
> probably going to routing for BGP but you can verify it 
>here. 
> 
> 
> Is anything else running on the router? OSPF, VPN, 
>PPPoE, etc? 
> 
> 
> Where BGP really matters is when you lose one of your 
>peers and it goes through 
> and updates the tables. On lower powered boxes, this 
>will peg the CPU and can 
> cause OSPF flaps, dropped packets and other issues. 
> 
> 
> On Mon, May 8, 2017 at 11:42 PM, Steve Jones < 
>[email protected] > wrote: 
> 
> 
> 
> 
> We turned up BGP on one of our routers today, 2 peers, 
>full routes, this is just one upstream, we will be 
>turning up bgp with another provider shortly elsewhere on 
>the network, I assume those tables will make their way to 
>this router. 
> load averaged 4-12% prior to turning up BGP now its 
>running 60-90, even occasionally pegged 
> 
> 
> is this a matter of tuning BGP and ROS packages, or is 
>this just too much for the router? this is only at 
>150mbps, as we increase capacity I feel we have already 
>scaled out of this router if its not a misconfiguration 
>of something on my end 
> 
> 
> 
> 
> Inline image 1 
> 
> 
> 

----- GENIAS INTERNET -- www.genias.net ------ 
Stefan Englhardt Email: [email protected] 
Dr. Gesslerstr. 20 D-93051 Regensburg 
Tel: +49 941 942798-0 Fax: +49 941 942798-9 


Reply via email to