Hello Khaled, Vol 1, 10 is an interesting lab. In order to gain full reachability, I took the 150.100.78.0 0.0.0.255 area 78 off of the router ospf 1 process on R8. I left the router ospf 2; 150.100.78.0 0.0.0.255 area 0 on R8. Hope this helps.
Deb On Feb 13, 2012 1:49 AM, "khaled al-ajeman" <[email protected]> wrote: > Hi There, > > According to the ipexpert workbook volume # 1 lab 10 question # 10.12-- we > have to configure area 78 which is between R7 AND R8 > as STUB area ( the question does not allow LSA 4 AND LSA 5. Therefore, I > am no allowed to configure area 78 as NSSA area, I hope this > is understood clearly. Secondly, I am being able to see route route > 200.0.0.11 on R8 only but on the other routers. > > thanks so much, > > > khaled > > On Mon, Feb 13, 2012 at 2:38 AM, Oluwagbenga Oyebande < > [email protected]> wrote: > > > I think you are referring to the *re*distribution in Vol 1 Lab 9 > > > > Do you see see the route to 200.0.0.11 on R8, R7 and R2? > > > > > > > > > > > > > > > > On Sun, Feb 12, 2012 at 9:21 AM, khaled al-ajeman < > > [email protected]> wrote: > > > >> Hi guys, > >> > >> I have configured the distribution between R8 AND cat1. R8 is the ASBR > >> that contained both ospf processes ( ospf 1 and ospf 2). > >> > >> However on R1 I do not see the route 150.100.81.0 NOR 200.0.0.11 on the > >> routing table of R1. CAN anyone tell me why ? below are my > configurations. > >> > >> R8 -ASBR > >> router ospf 1 > >> area 78 stub > >> redistribute ospf 2 subnets ----------------------> the > distribution > >> statement bet R8 OSPF and CAT OSPF process. > >> passive-interface default > >> no passive-interface FastEthernet0/0 > >> no passive-interface Serial0/0 > >> no passive-interface FastEthernet0/1 > >> network 100.100.200.0 0.0.0.255 area 200 > >> network 150.100.78.0 0.0.0.255 area 78 > >> network 150.100.178.0 0.0.0.255 area 78 > >> router ospf 2 > >> log-adjacency-changes > >> redistribute ospf 1 subnets > >> passive-interface default > >> no passive-interface FastEthernet0/1 > >> network 150.100.81.0 0.0.0.255 area 0 > >> > >> > >> CAT 1 > >> > >> > >> router ospf 2 > >> log-adjacency-changes > >> passive-interface default > >> no passive-interface FastEthernet0/1 > >> network 150.100.81.0 0.0.0.255 area 0 > >> network 200.0.0.11 0.0.0.0 area 0 > >> Best regards, > >> > >> khaled > >> > > _______________________________________________ > >> For more information regarding industry leading CCIE Lab training, > please > >> visit www.ipexpert.com > >> > >> Are you a CCNP or CCIE and looking for a job? Check out > >> www.PlatinumPlacement.com <http://www.platinumplacement.com/> > >> > >> http://onlinestudylist.com/mailman/listinfo/ccie_rs > >> > > > > > > > > -- > > -- > > Olugbenga Oyebande > > MD, DAIT > > 234-803-302-5287 > > http://www.dait-ng.com > > Cisco Networks, Network Security & Quality of Service > > DAIT Linux Enterprise Network Servers, Web Portal Projects > > Broadband Internet Deployment & ISP Consultancy > > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
