One more time: Take the third network statement (150.100.81.0) off of router ospf 1, on R8. You will have reachability from R1.
This is contrary to the instructions, Vol 1, Task 10.12. On Feb 14, 2012 5:54 AM, "khaled al-ajeman" <[email protected]> wrote: > Hi there, > > finally it is working, but from R1 I am not being able to ping to > 150.100.81.0 network, although I have configured the 150.100.81.0 network on > ospf 1 process on both routers R8 AND CAT1, however, the good news I am > being able to ping the lo0 interface 200.0.0.11 at cat1 from R1 > successfully. Below are my configurations for R8 AND CAT1 > > R8 > > router ospf 1 > log-adjacency-changes > area 78 stub > redistribute ospf 2 subnets > passive-interface default > no passive-interface FastEthernet0/0 > no passive-interface Serial0/0 > no passive-interface FastEthernet0/1 > no passive-interface Tunnel78 > network 100.100.200.0 0.0.0.255 area 200 > network 150.100.78.0 0.0.0.255 area 78 > network 150.100.81.0 0.0.0.255 area 78 > network 150.100.178.0 0.0.0.255 area 0 > router ospf 2 > log-adjacency-changes > redistribute ospf 1 subnets > passive-interface default > no passive-interface FastEthernet0/1 > network 150.100.81.0 0.0.0.255 area 0 > cat1 > > router ospf 2 > log-adjacency-changes > passive-interface default > no passive-interface FastEthernet0/1 > network 150.100.81.0 0.0.0.255 area 0 --------> this network not > available at R1's routing table, Why? > network 200.0.0.11 0.0.0.0 area 0 -------> this network is visible > from R1 > > thanks for you all, > > best regards, > khaled > > > > On Mon, Feb 13, 2012 at 4:09 PM, Debra Taylor <[email protected]>wrote: > >> Correction, the 150.100.81.0; not the 78 network off of router ospf 1 >> Apologies. >> On Feb 13, 2012 8:06 AM, "Debra Taylor" <[email protected]> wrote: >> >>> Hello Khaled, >>> >>> Vol 1, 10 is an interesting lab. In order to gain full reachability, I >>> took the 150.100.78.0 0.0.0.255 area 78 off of the router ospf 1 process on >>> R8. I left the router ospf 2; 150.100.78.0 0.0.0.255 area 0 on R8. Hope >>> this helps. >>> >>> Deb >>> On Feb 13, 2012 1:49 AM, "khaled al-ajeman" <[email protected]> >>> wrote: >>> >>>> Hi There, >>>> >>>> According to the ipexpert workbook volume # 1 lab 10 question # 10.12-- >>>> we >>>> have to configure area 78 which is between R7 AND R8 >>>> as STUB area ( the question does not allow LSA 4 AND LSA 5. Therefore, >>>> I >>>> am no allowed to configure area 78 as NSSA area, I hope this >>>> is understood clearly. Secondly, I am being able to see route route >>>> 200.0.0.11 on R8 only but on the other routers. >>>> >>>> thanks so much, >>>> >>>> >>>> khaled >>>> >>>> On Mon, Feb 13, 2012 at 2:38 AM, Oluwagbenga Oyebande < >>>> [email protected]> wrote: >>>> >>>> > I think you are referring to the *re*distribution in Vol 1 Lab 9 >>>> > >>>> > Do you see see the route to 200.0.0.11 on R8, R7 and R2? >>>> > >>>> > >>>> > >>>> > >>>> > >>>> > >>>> > >>>> > On Sun, Feb 12, 2012 at 9:21 AM, khaled al-ajeman < >>>> > [email protected]> wrote: >>>> > >>>> >> Hi guys, >>>> >> >>>> >> I have configured the distribution between R8 AND cat1. R8 is the >>>> ASBR >>>> >> that contained both ospf processes ( ospf 1 and ospf 2). >>>> >> >>>> >> However on R1 I do not see the route 150.100.81.0 NOR 200.0.0.11 on >>>> the >>>> >> routing table of R1. CAN anyone tell me why ? below are my >>>> configurations. >>>> >> >>>> >> R8 -ASBR >>>> >> router ospf 1 >>>> >> area 78 stub >>>> >> redistribute ospf 2 subnets ----------------------> the >>>> distribution >>>> >> statement bet R8 OSPF and CAT OSPF process. >>>> >> passive-interface default >>>> >> no passive-interface FastEthernet0/0 >>>> >> no passive-interface Serial0/0 >>>> >> no passive-interface FastEthernet0/1 >>>> >> network 100.100.200.0 0.0.0.255 area 200 >>>> >> network 150.100.78.0 0.0.0.255 area 78 >>>> >> network 150.100.178.0 0.0.0.255 area 78 >>>> >> router ospf 2 >>>> >> log-adjacency-changes >>>> >> redistribute ospf 1 subnets >>>> >> passive-interface default >>>> >> no passive-interface FastEthernet0/1 >>>> >> network 150.100.81.0 0.0.0.255 area 0 >>>> >> >>>> >> >>>> >> CAT 1 >>>> >> >>>> >> >>>> >> router ospf 2 >>>> >> log-adjacency-changes >>>> >> passive-interface default >>>> >> no passive-interface FastEthernet0/1 >>>> >> network 150.100.81.0 0.0.0.255 area 0 >>>> >> network 200.0.0.11 0.0.0.0 area 0 >>>> >> Best regards, >>>> >> >>>> >> khaled >>>> >> >>>> > _______________________________________________ >>>> >> For more information regarding industry leading CCIE Lab training, >>>> please >>>> >> visit www.ipexpert.com >>>> >> >>>> >> Are you a CCNP or CCIE and looking for a job? Check out >>>> >> www.PlatinumPlacement.com <http://www.platinumplacement.com/> < >>>> http://www.platinumplacement.com/> >>>> >> >>>> >> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>>> >> >>>> > >>>> > >>>> > >>>> > -- >>>> > -- >>>> > Olugbenga Oyebande >>>> > MD, DAIT >>>> > 234-803-302-5287 >>>> > http://www.dait-ng.com >>>> > Cisco Networks, Network Security & Quality of Service >>>> > DAIT Linux Enterprise Network Servers, Web Portal Projects >>>> > Broadband Internet Deployment & ISP Consultancy >>>> > >>>> > >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, >>>> please visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>>> >>>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>>> >>> > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
