I think it's also important here that the original poster should be figuring out WHY it's not working and HOW to make it work without just turning to the list and asking for an answer!
Is the prefix present in the originating router's LSDB? Is the prefix being advertised to neighbors? Is the prefix being received by neighbors? Is the prefix being accepted into the LSDBs of the neighbors? Is the prefix making it into the RIBs of the neighbors? There are shows and debugs to examine these things! Follow the path! This is CCIE lab preparation. If you can't figure out why a prefix isn't making it into your IGP, you are going to have some real trouble on lab day! If you're really stuck, consult the DSG. Make it work with the DSG's solution. If the DSG solution doesn't work for you (after checking all your config along the way), or you really don't understand why the DSG solution does work after researching the commands and protocol behaviors, then ask the list as a post-mortem. Sorry for the rant, but that's my 2 cents on the matter... There will be no help on Lab Day. Learn to help yourself with the tools you have. On Tue, Feb 14, 2012 at 9:12 AM, Oluwagbenga Oyebande < [email protected]> wrote: > I love exploring different methods when I have the time. It enhances the > learning process. But if I where you I would make it work according to the > instructions before exploring other methods. > > Remember CCIE lab must be done according to instructions. So maybe you > should get that first. You could then explore other shortcuts > > On 14 February 2012 14:07, Debra Taylor <[email protected]> wrote: > > > One more time: Take the third network statement (150.100.81.0) off of > > router ospf 1, on R8. You will have reachability from R1. > > > > This is contrary to the instructions, Vol 1, Task 10.12. > > On Feb 14, 2012 5:54 AM, "khaled al-ajeman" <[email protected]> > > wrote: > > > > > Hi there, > > > > > > finally it is working, but from R1 I am not being able to ping to > > > 150.100.81.0 network, although I have configured the 150.100.81.0 > > network on > > > ospf 1 process on both routers R8 AND CAT1, however, the good news I am > > > being able to ping the lo0 interface 200.0.0.11 at cat1 from R1 > > > successfully. Below are my configurations for R8 AND CAT1 > > > > > > R8 > > > > > > router ospf 1 > > > log-adjacency-changes > > > area 78 stub > > > redistribute ospf 2 subnets > > > passive-interface default > > > no passive-interface FastEthernet0/0 > > > no passive-interface Serial0/0 > > > no passive-interface FastEthernet0/1 > > > no passive-interface Tunnel78 > > > network 100.100.200.0 0.0.0.255 area 200 > > > network 150.100.78.0 0.0.0.255 area 78 > > > network 150.100.81.0 0.0.0.255 area 78 > > > network 150.100.178.0 0.0.0.255 area 0 > > > router ospf 2 > > > log-adjacency-changes > > > redistribute ospf 1 subnets > > > passive-interface default > > > no passive-interface FastEthernet0/1 > > > network 150.100.81.0 0.0.0.255 area 0 > > > cat1 > > > > > > router ospf 2 > > > log-adjacency-changes > > > passive-interface default > > > no passive-interface FastEthernet0/1 > > > network 150.100.81.0 0.0.0.255 area 0 --------> this network not > > > available at R1's routing table, Why? > > > network 200.0.0.11 0.0.0.0 area 0 -------> this network is > visible > > > from R1 > > > > > > thanks for you all, > > > > > > best regards, > > > khaled > > > > > > > > > > > > On Mon, Feb 13, 2012 at 4:09 PM, Debra Taylor <[email protected] > > >wrote: > > > > > >> Correction, the 150.100.81.0; not the 78 network off of router ospf 1 > > >> Apologies. > > >> On Feb 13, 2012 8:06 AM, "Debra Taylor" <[email protected]> > > wrote: > > >> > > >>> Hello Khaled, > > >>> > > >>> Vol 1, 10 is an interesting lab. In order to gain full > reachability, I > > >>> took the 150.100.78.0 0.0.0.255 area 78 off of the router ospf 1 > > process on > > >>> R8. I left the router ospf 2; 150.100.78.0 0.0.0.255 area 0 on R8. > > Hope > > >>> this helps. > > >>> > > >>> Deb > > >>> On Feb 13, 2012 1:49 AM, "khaled al-ajeman" < > [email protected] > > > > > >>> wrote: > > >>> > > >>>> Hi There, > > >>>> > > >>>> According to the ipexpert workbook volume # 1 lab 10 question # > > 10.12-- > > >>>> we > > >>>> have to configure area 78 which is between R7 AND R8 > > >>>> as STUB area ( the question does not allow LSA 4 AND LSA 5. > > Therefore, > > >>>> I > > >>>> am no allowed to configure area 78 as NSSA area, I hope this > > >>>> is understood clearly. Secondly, I am being able to see route route > > >>>> 200.0.0.11 on R8 only but on the other routers. > > >>>> > > >>>> thanks so much, > > >>>> > > >>>> > > >>>> khaled > > >>>> > > >>>> On Mon, Feb 13, 2012 at 2:38 AM, Oluwagbenga Oyebande < > > >>>> [email protected]> wrote: > > >>>> > > >>>> > I think you are referring to the *re*distribution in Vol 1 Lab 9 > > >>>> > > > >>>> > Do you see see the route to 200.0.0.11 on R8, R7 and R2? > > >>>> > > > >>>> > > > >>>> > > > >>>> > > > >>>> > > > >>>> > > > >>>> > > > >>>> > On Sun, Feb 12, 2012 at 9:21 AM, khaled al-ajeman < > > >>>> > [email protected]> wrote: > > >>>> > > > >>>> >> Hi guys, > > >>>> >> > > >>>> >> I have configured the distribution between R8 AND cat1. R8 is > the > > >>>> ASBR > > >>>> >> that contained both ospf processes ( ospf 1 and ospf 2). > > >>>> >> > > >>>> >> However on R1 I do not see the route 150.100.81.0 NOR 200.0.0.11 > on > > >>>> the > > >>>> >> routing table of R1. CAN anyone tell me why ? below are my > > >>>> configurations. > > >>>> >> > > >>>> >> R8 -ASBR > > >>>> >> router ospf 1 > > >>>> >> area 78 stub > > >>>> >> redistribute ospf 2 subnets ----------------------> the > > >>>> distribution > > >>>> >> statement bet R8 OSPF and CAT OSPF process. > > >>>> >> passive-interface default > > >>>> >> no passive-interface FastEthernet0/0 > > >>>> >> no passive-interface Serial0/0 > > >>>> >> no passive-interface FastEthernet0/1 > > >>>> >> network 100.100.200.0 0.0.0.255 area 200 > > >>>> >> network 150.100.78.0 0.0.0.255 area 78 > > >>>> >> network 150.100.178.0 0.0.0.255 area 78 > > >>>> >> router ospf 2 > > >>>> >> log-adjacency-changes > > >>>> >> redistribute ospf 1 subnets > > >>>> >> passive-interface default > > >>>> >> no passive-interface FastEthernet0/1 > > >>>> >> network 150.100.81.0 0.0.0.255 area 0 > > >>>> >> > > >>>> >> > > >>>> >> CAT 1 > > >>>> >> > > >>>> >> > > >>>> >> router ospf 2 > > >>>> >> log-adjacency-changes > > >>>> >> passive-interface default > > >>>> >> no passive-interface FastEthernet0/1 > > >>>> >> network 150.100.81.0 0.0.0.255 area 0 > > >>>> >> network 200.0.0.11 0.0.0.0 area 0 > > >>>> >> Best regards, > > >>>> >> > > >>>> >> khaled > > >>>> >> > > >>>> > _______________________________________________ > > >>>> >> For more information regarding industry leading CCIE Lab > training, > > >>>> please > > >>>> >> visit www.ipexpert.com > > >>>> >> > > >>>> >> Are you a CCNP or CCIE and looking for a job? Check out > > >>>> >> www.PlatinumPlacement.com <http://www.platinumplacement.com/> < > > >>>> http://www.platinumplacement.com/> > > >>>> >> > > >>>> >> http://onlinestudylist.com/mailman/listinfo/ccie_rs > > >>>> >> > > >>>> > > > >>>> > > > >>>> > > > >>>> > -- > > >>>> > -- > > >>>> > Olugbenga Oyebande > > >>>> > MD, DAIT > > >>>> > 234-803-302-5287 > > >>>> > http://www.dait-ng.com > > >>>> > Cisco Networks, Network Security & Quality of Service > > >>>> > DAIT Linux Enterprise Network Servers, Web Portal Projects > > >>>> > Broadband Internet Deployment & ISP Consultancy > > >>>> > > > >>>> > > > >>>> _______________________________________________ > > >>>> For more information regarding industry leading CCIE Lab training, > > >>>> please visit www.ipexpert.com > > >>>> > > >>>> Are you a CCNP or CCIE and looking for a job? Check out > > >>>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> > > >>>> > > >>>> http://onlinestudylist.com/mailman/listinfo/ccie_rs > > >>>> > > >>> > > > > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, please > > visit www.ipexpert.com > > > > Are you a CCNP or CCIE and looking for a job? Check out > > www.PlatinumPlacement.com > > > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > > > > > > -- > -- > Olugbenga Oyebande > MD, DAIT > 234-803-302-5287 > http://www.dait-ng.com > Cisco Networks, Network Security & Quality of Service > DAIT Linux Enterprise Network Servers, Web Portal Projects > Broadband Internet Deployment & ISP Consultancy > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
