> > What model 6I24 do you have? > 6i24-25
El sáb., 7 mar. 2020 a las 13:20, Peter C. Wallace (<[email protected]>) escribió: > On Sat, 7 Mar 2020, Leonardo Marsaglia wrote: > > > Date: Sat, 7 Mar 2020 13:02:11 -0300 > > From: Leonardo Marsaglia <[email protected]> > > Reply-To: "Enhanced Machine Controller (EMC)" > > <[email protected]> > > To: "Enhanced Machine Controller (EMC)" <[email protected] > > > > Subject: Re: [Emc-users] 6i24 + 7i44 configuration > > > > Hello Peter, > > > > Thanks for the answer as always. I'll try to change P4 to P1 because in > the > > way I'm mounting the boards that's the simpler and less painful solution > to > > plug the 7i52s and 7i44. > > > What model 6I24 do you have? > > > > > > As you can see in the picture, the 7i52s is on the top plate, and the > 7i44 > > is placed on the bottom plate next to the motherboard. On the top plate > I'm > > mounting also the 7i70 and 7i71. So to reach the 7i52s the best for me is > > to use the P1 connector. I should have thought about this before > anyway... > > > > El sяяb., 7 mar. 2020 a las 12:48, Peter C. Wallace (<[email protected]>) > > escribiяя: > > > >> On Sat, 7 Mar 2020, Leonardo Marsaglia wrote: > >> > >>> Date: Sat, 7 Mar 2020 10:20:52 -0300 > >>> From: Leonardo Marsaglia <[email protected]> > >>> Reply-To: "Enhanced Machine Controller (EMC)" > >>> <[email protected]> > >>> To: "Enhanced Machine Controller (EMC)" < > [email protected] > >>> > >>> Subject: Re: [Emc-users] 6i24 + 7i44 configuration > >>> > >>> Hello again to all, > >> > >>> I'm reviving this discussion because I started attempting to configure > my > >>> setup to finally mount it on the machine (once it all works well off > >>> course). > >>> > >>> Basically I'm using the 6i24 connected to a 7i52s for step output and > to > >>> read 1 encoder. Here's where I have the first doubts, mostly because I > >>> don't do this too often. > >>> > >>> If I want to use the full 6 stepgens and 6 encoder inputs of the > bitfile > >>> Peter made for my 6i24 I see on the dmesg that the encoder and stepens > are > >>> distributed between P3 and P4 of the board. Is this ok? Because the > 7i52s > >>> as you know only has one 50 pin flat cable port. I'm not planning to > use > >>> that much encoders and steppers but this guides me to the next > question. > >> > >> Thats because you are using a SVSTSS12_12_8_7I52SX2 configuration setup > >> for > >> two 7I52S on P4 and P3 (if you just have 1 7I52S, only enable 6 stepgens > >> and 6 encoders and the P3 connector will revert to just GPIO) > >> > >> > >>> Is there an easy way to see the correspondence between the pins on the > >> 6i24 > >>> and the ones on the 7i52s ? Because if I use only 3 stepgens and 1 > encoder > >>> I can see they are all in the P4 connector and I have also some free > I/Os > >>> on that connector too but I don't know how to identify them on the > 7i52s > >>> other than start probing them one by one. > >> > >> You can look at the pinout file and the 7I52S manual but its simpler > than > >> that, the stepgens and encoders are simply in the 7I52S manual order, > that > >> is > >> encoders 0..5 match the manual exactly, and Step0 = TX0A, Dir0 =TX0B, > Step1 > >> =TX1A, Dir1=TX1B etc etc. > >> > >> > >> > >>> Besides that, I need to modify the PIN file since I need the 7i52s to > be > >>> plugged to P1 connector of the 6i24 (Notice that the 6i24 has three > ports > >>> labelled P1, P3, P4). I'm downloading Xilinx ISE 14.7 to try to modify > the > >>> original file that Peter made for me. > >> > >> You can do this but I'm not sure why you would care about the 6I24 > >> connector order. > >> > >>> Well, that's all for now, if you can help me a little bit I surely can > >> make > >>> all this work this weekend hopefully. I also need to try the 7i44 but I > >>> need to understand this first. > >>> > >>> Thanks as always for your help and patience! > >> > >> The 7I44 connects to P1, thats about it > >> > >>> > >> > >> _______________________________________________ > >> Emc-users mailing list > >> [email protected] > >> https://lists.sourceforge.net/lists/listinfo/emc-users > >> > >> Peter Wallace > >> Mesa Electronics > >> > >> (\__/) > >> (='.'=) This is Bunny. Copy and paste bunny into your > >> (")_(") signature to help him gain world domination. > >> > >> > >> > >> _______________________________________________ > >> Emc-users mailing list > >> [email protected] > >> https://lists.sourceforge.net/lists/listinfo/emc-users > >> > > > > Peter Wallace > Mesa Electronics > > (\__/) > (='.'=) This is Bunny. Copy and paste bunny into your > (")_(") signature to help him gain world domination. > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
